Instrukcja obsługi Dri Eaz HEPA 700

Dri Eaz oczyszczacz powietrza HEPA 700

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Dri Eaz HEPA 700 (11 stron) w kategorii oczyszczacz powietrza. Ta instrukcja była pomocna dla 4 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/11

124775B HEPA 700 1 Legend Brands, Inc.

Owner s ’

Manual

HEPA 700 Air Scrubber

The HEPA 700 draws air in from the surrounding environment and passes it through an advanced ltration

system. The unit removes airborne particles such as dust, mold spores, pollen, pet dander and other debris, and

odors, and can be congured for negative or positive-pressure ltration setups.

R E A D A N D U N D E R S T A N D B E F O R E O P E R A T I N G

ELECTRIC SHOCK HAZARD

The unit must be electrically grounded. Use only on

GFCI protected receptacles.

Connect to a properly grounded outlet only. Do not cut

o the grounding prong. Do not use with an adapter.

Do not use with extension cords.

Do not use with damaged cord or plug. If unit is not working as

it should, has been dropped, damaged, left outdoors, or

exposed to water, return it to an authorized service center for

repair.

Unplug cord from outlet when not in use or when servicing unit.

ELECTRIC SHOCK HAZARD

Keep motor and electrical parts dry.

Do not use outdoors. For indoor use only.

Do not handle plug or unit with wet hands.

Do not operate unit in standing water.

BREATHING HAZARD

When using the HEPA 700 in a containment area, turn

o all sources of power to open combustion

appliances such as replaces, boilers, furnaces, water

heaters and HVAC systems to avoid the risk of backdrafting

deadly carbon monoxide fumes.

This equipment has been tested and found to comply

with the limits for a Class B digital device, pursuant to

part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a

residential installation. This equipment generates, uses and

can radiate radio frequency energy, and if not installed and

used in accordance with the instructions, may cause harmful

interference to radio communications. However, there is no

guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference

to radio or television reception, which can be determined by

turning the equipment o and on, the user is encouraged to try

to correct the interference by one or more of the following

measures:

• Reorient or relocate the receiving antenna

• Increase the separation between the equipment and receiver

• Connect the equipment into an outlet on a circuit different

from that to which the receiver is connected

• Consult the dealer or an experienced radio/TV technician for

help

ATWINC3400-MR210CA module approvals:

• United States/FCC ID: 2ADHKWINC3400

• Canada/ISED:

o IC: 20266-ATWINC3400

o HVIN: ATWINC3400-MR210CA

o PMN: Wi-Fi and Bluetooth Module

Parts Identication

Inlet and

inlet cover.

Remove

cover

before

operating.

Air intake

ring. Attach

14 in. semi-

rigid ducting.

Feet for

horizontal

operation &

stacking.

Carry handle.

Folds down when

not in use.

Filter cover buckle

(×4). Release to

replace lter

elements.

Use the hook- d-pile an

fasteners to attach the inlet

cover here while unit is use.

115V outlets

(×2) and

breaker reset

switch.

Filtered air

outlet. Filter

retainer ring may

be used to

attach in. 14

diam. layat

ducting.

Control panel.

124775B HEPA 700 2 Legend Brands, Inc.

HEPA 700 APPLICATIONS

• Water Damage

• Construction Dust Control

• Mold Remediation

• Odor control

• The HEPA 700 can be used for dust Other uses:

abatement, re damage remediation, jobsite ventilation,

and positive or negative air setups for contamination

cleanup and cleanroom environments. Use in homes,

businesses, institutions, schools, hospitals, long term care

facilities, construction and remodel job sites.

NOTICE! Many of these applications can present

signicant health risks and require professional training.

Because federal, state/provincial, and local laws

and regulations have varying requirements for the

application, testing and general use of equipment on

asbestos abatement projects, Legend Brands cannot

warrant products for asbestos abatement. Contractors

performing abatement work should evaluate tools,

equipment and procedures in light of their local regulatory

requirements, and comply with those requirements.

WARRANTY REGISTRATION

Warranty.LegendBrandsRestoration.com

determine service is required, have your equipment model,

serial number and original proof of purchase available and call

your distributor to obtain a return material authorization (RMA)

or email service@legendbrandsrestoration.com.

SPECIAL FEATURES

Command Hub Technology

Integrated Command Hub technology with the free Command

Center mobile app enables rmware updates and 24/7

monitoring and control to ensure optimal air ltration. (App

available soon in Apple and Google Play stores.)

Ducting options

Inlet: in. wire reinforced ducting (purchased separately). 14

Outlet: (diameter) layat or wire reinforced ducting 14 in.

(purchased separately) using the provided duct attachment

ring. Take care not to bend or otherwise damage the

attachment ring when installing the ducting. Do not exceed a

maximum ducting length of 7.6 m. 25 ft. /

Negative Pressure Setup

The HEPA 700 can be set up for a negative pressure

containment area. Only professionals with the appropriate

training should set up negative pressure containment areas.

Stacking for Storage and Operation

Stack the HEPA 700 up to three high for storage or transport.

Secure the units when stacked for transport.

The unit can also be operated on its back, with the outlet

facing upward.

CONTROLS AND OPERATING

INSTRUCTIONS

Setup

1. Unwrap the cord completely.

2. Place the HEPA 700 with the handle up. Ensure that neither

the inlet nor the outlet are obstructed.

3. 115V Plug a standard in to GFCI-protected outlet.

Electrical Outlets

You can connect up to eight (8 HEPA 700s on a 15-amp )

circuit on the lowest speed; four (4) on the highest speed .

Command Hub - Home

On/Off. Swit unit on or o ches .

Use + / - to adjust blower speed.

Menu. Select to view system info, service, error

messages, wireless setup, settings, and other information. Go

to HEPA700.legendbrandsrestoration.com for more info.

GFCI Outlet Reset and Test

MAINTENANCE

ELECTRIC SHOCK HAZARD. Disconnect from

electrical supply prior to servicing or cleaning.

BREATHING HAZARD. Always wear an

appropriate NIOSH-approved respirator and

personal protective equipment when removing or

replacing lters, or when cleaning the HEPA . 700

About the lters

IMPORTANT: Use Legend Brands HEPA 700 lters only

(see Filter Options below). Use of other lters will

reduce filtration effectiveness.

Regularly check and replace the prefilter(s) and HEPA

primary lter as needed. The control panel will indicate

when the HEPA primary filter needs to be replaced.

Filters are not reusable. Do not attempt to clean and reuse.

NOTICE: When using the HEPA 700 on remediation

projects, change BOTH lters after every job. Dispose of

contaminated lters properly.

Replacing the Prefilter

The prefilter should be replaced more frequently to help

preserve the life of the HEPA lter.

1. Lay unit on its back and release the four (4) buckles. Lift o

the lter door.

WARNING

WARNINGWARNING

124775B HEPA 700 3 Legend Brands, Inc.

2. Remove the prelter from the lter door and discard.

3. Insert new prelter into lter door. Ensure that the prelter is

seated properly on the retention tabs.

4. To replace the HEPA Primary lter, proceed to the next step.

Otherwise, replace lter assembly on to unit and reattach the

four buckles.

Replacing the HEPA Primary Filter

IMPORTANT: Performance is reduced when a non-Legend

Brands primary lter is installed. For maximum ltration

performance, use only Legend Brands lters. Do not clean

and reuse the HEPA lter. Always replace the prelter when

replacing the HEPA lter.

1. Lay unit on its back and release the four (4) buckles. Lift

o the lter door.

2. Remove the prelter from the lter door and discard.

3. Release the two locking tabs and lift out primary lter

element. Discard used lter.

4. Replace HEPA primary lter, handling it with care, as lter

is easily damaged. Do not use a lter that is damaged.

5. Place new prelter(s) in lter door. Replace lter cover and

lock the four buckles securely.

Before each use

Inspect the electrical cord for damage, and do not e the unit us

if you nd any fraying, cuts, etc. Contact your local distributor

for service.

As Needed

Clean exterior of housing and inside the lter compartment.

Ensure housing is completely dry before reassembling. Do not

apply liquids to control panel or to any electrical components.

When using the HEPA 700 for remediation or in

sensitive environments:

• Wear NIOSH-approved protective gear when changing

lters.

• Change both lters after every remediation job.

• Dispose of used lters according to local regulations.

• Replace both the prelter and HEPA filter to prevent

cross-contamination.

• Clean the unit thoroughly (vacuum and damp wipe per

IICRC S520, 10.11) before removing it from the

containment area to avoid cross-contamination. Let the

unit dry before installing clean lters.

For parts and service contact your local distributor or Legend Brands: Live Chat - Info.legendbrands.com | Email:

Service@legendbrandsrestoration.com

Filter Options

Air Filtration Applications:

Prelter(s)

Removes larger

particulates protects –

primary lter

Specialty Prelter

Carbon removes

VOCs and odors

Primary lter (HEPA)

Removes ne particulate

down to .3 microns

• Water loss air ltration and mold

remediation*

• For high particle Standard air scrubbing.

loads, such as construction or remodeling sites.

2-in. MERV 8 Pleated

Paper Filter

#125026 (6 pk.)

HEPA Filter

#124966 (1 pk.)

#125028 (8 pk.)

• For removing Odor control and air ltration.

volatile organic compounds (VOCs), fumes from

paint and paint thinners, and many other

noxious odors, eg, from food, sewage, etc.

• Paper Smoke particulate and odor removal.

prelter and HEPA lter remove particulates

and carbon lter adsorbs odors.

1-in. MERV 8 Pleated

Paper Filter

#125029 (12 pk.)

1-in. Activated

Carbon Filter

#125027 (4 pk.)

HEPA Filter

#124966 (1 pk.)

#125028 (8 pk.)

SPECIFICATIONS

Model

HEPA 700 (#125105)

Airow

Variable to 700 CFM | CMH 1189

Static pressure

3.0 in. (H2O) | 747 Pa

Weight

42.0 lbs. | 19.1 kg

Dimensions

(H × D × W)

22.8 × 17.0 × 25.9 in.

57.9 × 43.3 × 65.9 cm

Amps/Power

1.5 - 3.0 amps, 115v, 60 Hz, 350w

Power cord

25 ft. | 7.6 m

Duct size

14 in. | 35.6 cm

Construction

Injection-molded plastic housing

Xactimate

WTRNAFAN>

Safety

ETL listed to UL 507 and CSA C22.2 No. 113

Specications are subject to change without notice. Some values

may be approximate.

Specyfikacje produktu

Marka:	Dri Eaz
Kategoria:	oczyszczacz powietrza
Model:	HEPA 700

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Dri Eaz HEPA 700, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje oczyszczacz powietrza Dri Eaz

Dri Eaz HEPA 700 Instrukcja

28 Grudnia 2024

Dri Eaz F530 Instrukcja

25 Września 2024

Dri Eaz LGR 7000XLi Instrukcja

20 Września 2024

Dri Eaz LGR 2800i Instrukcja

17 Września 2024

Instrukcje oczyszczacz powietrza

Najnowsze instrukcje dla oczyszczacz powietrza

Uniprodo UNI_AIR PURIFIER_03 Instrukcja

4 Stycznia 2025

Haier QDHR20 Instrukcja

4 Stycznia 2025

Sunbeam Fresh Protect SAP1000WH Instrukcja

30 Grudnia 2025

Honeywell HPA250B Instrukcja

29 Grudnia 2024

Honeywell HPA300COM Instrukcja

29 Grudnia 2024

Winix AUS-0850AAPU Instrukcja

29 Grudnia 2024

TruSens Z-2000 Instrukcja

28 Grudnia 2024

Levoit Core 300S Plus Smart Instrukcja

28 Grudnia 2024

Pingi Cascada CHD-W6000M Instrukcja

27 Grudnia 2024

Haus & Luft HL-OP-11/WiFi Instrukcja

27 Grudnia 2024