Instrukcja obsługi Dremel 400seriesXPR

Dremel szlifierka 400seriesXPR

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Dremel 400seriesXPR (72 stron) w kategorii szlifierka. Ta instrukcja była pomocna dla 6 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/72

Instructional Safety

Manual

400 Series XPR

High Performance Rotary Tool

1-800-437-3635

http://www.dremel.com

Dremel brand products are manufactured and sold by the

Dremel Division of Robert Bosch Tool Corporation

Read and understand all instructions. Failure to follow all instructions list-

ed below, may result in electric shock, fire and/or serious personal injury.

SAVE THESE INSTRUCTIONS

WORK AREA

Keep your work area clean and well lit.

Cluttered benches and dark areas invite acci-

dents.

Do not operate power tools in explosive

atmospheres, such as in the presence of

flammable liquids, gases, or dust. Power

tools create sparks which may ignite the dust

or fumes.

Keep bystanders, children, and visitors

away while operating a power tool.

Distractions can cause you to lose control.

Electrical Safety

Double Insulated tools are equipped with

a polarized plug (one blade is wider than

the other.) This plug will fit in a polarized

outlet only one way. If the plug does not

fit fully in the outlet, reverse the plug. If it

still does not fit, contact a qualified elec-

trician to install a polarized outlet. Do not

change the plug in any way. Double

Insulation eliminates the need for the three

wire grounded power cord and grounded

power supply system. Before plugging in the

tool, be certain the outlet voltage supplied is

within the voltage marked on the nameplate.

Do not use “AC only” rated tools with a DC

power supply.

Avoid body contact with grounded sur-

faces such as pipes, radiators, ranges

and refrigerators. There is an increased risk

of electric shock if your body is grounded. If

operating the power tool in damp locations is

unavoidable, a Ground Fault Circuit

Interrupter must be used to supply the power

to your tool. Electrician’s rubber gloves and

footwear will further enhance your personal

safety.

Don't expose power tools to rain or wet

conditions. Water entering a power tool will

increase the risk of electric shock.

Do not abuse the cord. Never use the cord

to carry the tools or pull the plug from an

outlet. Keep cord away from heat, oil,

sharp edges or moving parts. Replace

damaged cords immediately. Damaged

cords increase the risk of electric shock.

When operating a power tool outside, use

an outdoor extension cord marked "W-A"

or "W." These cords are rated for outdoor

use and reduce the risk of electric shock.

Personal Safety

Stay alert, watch what you are doing and

use common sense when operating a

power tool. Do not use tool while tired or

under the influence of drugs, alcohol, or

medication. A moment of inattention while

operating power tools may result in serious

personal injury.

Dress properly. Do not wear loose cloth-

ing or jewelry. Contain long hair. Keep

your hair, clothing, and gloves away from

moving parts. Loose clothes, jewelry, or

long hair can be caught in moving parts.

Keep handles dry, clean and free from oil and

grease.

Avoid accidental starting. Be sure switch

is “OFF” before plugging in. Carrying tools

with your finger on the switch or plugging in

tools that have the switch “ON” invites acci-

dents.

Remove adjusting keys or wrenches

before turning the tool ON. A wrench or a

key that is left attached to a rotating part of

the tool may result in personal injury.

Do not overreach. Keep proper footing

and balance at all times. Proper footing and

balance enables better control of the tool in

unexpected situations.

Use safety equipment. Always wear eye

protection. Dust mask, non-skid safety

shoes, hard hat, or hearing protection must

be used for appropriate conditions.

Tool Use and Care

Use clamps or other practical way to

secure and support the workpiece to a

stable platform. Holding the work by hand

or against your body is unstable and may

lead to loss of control.

Do not force tool. Use the correct tool for

your application. The correct tool will do the

job better and safer at the rate for which it is

designed.

Do not use tool if switch does not turn it

ON or OFF. Any tool that cannot be con-

trolled with the switch is dangerous and must

be repaired.

Disconnect the plug from the power

source before making any adjustments,

changing accessories, or storing the tool.

Such preventive safety measures reduce the

risk of starting the tool accidentally.

WARNING

POWER TOOL SAFETY RULES

Store idle tools out of reach of children

and other untrained persons. Tools are

dangerous in the hands of untrained users.

Maintain tools with care. Keep cutting

tools sharp and clean. Properly main-

tained tools, with sharp cutting edges are

less likely to bind and are easier to control.

Any alteration or modification is a misuse

and may result in a dangerous condition.

Check for misalignment or binding of

moving parts, breakage of parts, and any

other condition that may affect the tools

operation. If damaged, have the tool

serviced before using. Many accidents

are caused by poorly maintained tools.

Develop a periodic maintenance schedule

for your tool.

Use only accessories that are recom-

mended by the manufacturer for your

model. Accessories that may be suitable for

one tool, may become hazardous when

used on another tool.

Service

Tool service must be performed only by

qualified repair personnel. Service or

maintenance performed by unqualified per-

sonnel could result in a risk of injury. For

example: internal wires may be misplaced

or pinched, safety guard return springs may

be improperly mounted.

When servicing a tool, use only identical

replacement parts. Follow instructions in

the Maintenance section of this manual.

Use of unauthorized parts or failure to follow

Maintenance Instructions may create a risk

of electric shock or injury. Certain cleaning

agents such as gasoline, carbon tetrachlo-

ride, ammonia, etc. may damage plastic

parts.

SAFETY RULES FOR ROTARY TOOL

Accessories must be rated for at least the

speed recommended on the tool warning

label. Wheels and other accessories run-

ning over rated speed can fly apart and

cause injury.

Hold tool by insulated gripping surfaces

when performing an operation where the

cutting tool may contact hidden wiring or

its own cord. Contact with a "live" wire will

make exposed metal parts of the tool "live"

and shock the operator. If cutting into existing

walls or other blind areas where electrical

wiring may exist is unavoidable, disconnect

all fuses or circuit breakers feeding this work-

site.

Do not operate the flexible shaft with a

sharp bend. Over bending the shaft can

generate excessive heat on the jacket or

hand piece. The recommended minimum is

6" radius.

Always disconnect the power cord from

the power source before making any

adjustments or attaching any acces-

sories. You may unexpectedly cause the tool

to start leading to serious personal injury.

Be aware of the switch location, when

placing the tool down or when picking the

tool up. You may accidentally activate the

switch.

Always hold the hand piece firmly in your

hands during the start-up. The reaction

torque of the motor, as it accelerates to full

speed, can cause the shaft to twist.

Always wear safety goggles and dust

mask. Use only in well ventilated area.

Using personal safety devices and working in

safe environment reduces risk of injury.

After changing the bits or making any

adjustments, make sure the collet nut and

any other adjustment devices are secure-

ly tightened. Loose adjustment device can

unexpectedly shift, causing loss of control,

loose rotating components will be violently

thrown.

Do not reach in the area of the spinning

bit. The proximity of the spinning bit to your

hand may not always be obvious.

Allow brushes to run at operating speed

for at least one minute before using

wheel. During this time no one is to stand

in front or in line with the brush. Loose

bristles or wires will be discharged during the

run-in time.

Wire and bristle brushes must never be

operated at speeds greater than

15,000/min. Direct the discharge of the

spinning wire brush away from you.

Small particles and tiny wire fragments may

be discharged at high velocity during the

“cleaning” action with these brushes and may

become imbedded in your skin. Bristles or

wires will be discharged from the brush at

high speeds.

Carefully handle both the tool and individ-

ual grinding wheels to avoid chipping or

cracking. Install a new wheel if tool is

Specyfikacje produktu

Marka:	Dremel
Kategoria:	szlifierka
Model:	400seriesXPR

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Dremel 400seriesXPR, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje szlifierka Dremel

Dremel 200 Instrukcja

23 Września 2024

Dremel 400seriesXPR Instrukcja

16 Września 2024

Dremel 780 Instrukcja

15 Września 2024

Dremel 300series Instrukcja

3 Września 2024

Instrukcje szlifierka

Najnowsze instrukcje dla szlifierka

HiKOKI GP2S2 Instrukcja

15 Października 2024

Makita GA9060R Instrukcja

14 Października 2024

Hitachi G 13SR Instrukcja

14 Października 2024

Makita DGA700Z Instrukcja

12 Października 2024

Einhell NBG 150 Instrukcja

9 Października 2024

Einhell TE-AG 18/100 Li-Solo Instrukcja

9 Października 2024

Einhell TC-AG 100 Instrukcja

9 Października 2024

Einhell MWS 115/2 Instrukcja

9 Października 2024

Einhell Professional TP-AG 2320 Instrukcja

9 Października 2024

Einhell RT-AG 230/180 Instrukcja

9 Października 2024