Instrukcja obsługi Dremel 300 Series

Dremel Maszyna do śrub 300 Series

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Dremel 300 Series (72 stron) w kategorii Maszyna do śrub. Ta instrukcja była pomocna dla 16 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/72

Instructional Safety

Manual

300 Series

High Speed Rotary Tool

1-800-437-3635

http://www.dremel.com

Dremel brand products are manufactured and sold by the

Dremel Division of Robert Bosch Tool Corporation

DM 2610925781 5-05.qxd 5/12/05 10:31 PM Page 1

Read all instructions. Failure to follow all instructions listed below

may result in electric shock, fire and/or serious injury. The term “power

tool” in all of the warnings listed below refers to your mains-operated (corded) power tool

or battery-operated (cordless) power tool.

SAVE THESE INSTRUCTIONS

Work area safety

Keep work area clean and well lit.

Cluttered or dark areas invite accidents.

Do not operate power tools in explosive

atmospheres, such as in the presence of

flammable liquids, gases or dust. Power

tools create sparks which may ignite the

dust or fumes.

Keep children and bystanders away

while operating a power tool. Distractions

can cause you to lose control.

Electrical safety

Power tool plugs must match the outlet.

Never modify the plug in any way. Do not

use any adapter plugs with earthed

(grounded) power tools. Unmodified plugs

and matching outlets will reduce risk of elec-

tric shock.

Avoid body contact with earthed or

grounded surfaces such as pipes, radia-

tors, ranges and refrigerators. There is an

increased risk of electric shock if your body

is earthed or grounded.

Do not expose power tools to rain or wet

conditions. Water entering a power tool will

increase the risk of electric shock.

Do not abuse the cord. Never use the

cord for carrying, pulling or unplugging

the power tool. Keep cord away from

heat, oil, sharp edges or moving parts.

Damaged or entangled cords increase the

risk of electric shock.

When operating a power tool outdoors,

use an extension cord suitable for out-

door use. Use of a cord suitable for outdoor

use reduces the risk of electric shock.

Do not use AC only rated tools with a DC

power supply. While the tool may appear

to work, the electrical components of the AC

rated tool are likely to fail and create a haz-

ard to the operator.

If operating the power tool in damp loca-

tions is unavoidable a Ground Fault

Circuit Interrupter (GFCI) must be used

to supply the power to your tool. GFCI

and personal protection devices like electri-

cian’s rubber gloves and footwear will fur-

ther enhance your personal safety.

Personal safety

Stay alert, watch what you are doing and

use common sense when operating a

power tool. Do not use a power tool

while you are tired or under the influence

of drugs, alcohol or medication. A

moment of inattention while operating

power tools may result in serious personal

injury.

Use safety equipment. Always wear eye

protection. Safety equipment such as dust

mask, non-skid safety shoes, hard hat, or

hearing protection used for appropriate con-

ditions will reduce personal injuries.

Avoid accidental starting. Ensure the

switch is in the off-position before plug-

ging in. Carrying power tools with your fin-

ger on the switch or plugging in power tools

that have the switch on invites accidents.

Remove any adjusting key or wrench

before turning the power tool on. A

wrench or a key left attached to a rotating

part of the power tool may result in person-

al injury.

Do not overreach. Keep proper footing

and balance at all times. This enables bet-

ter control of the power tool in unexpected

situations.

Dress properly. Do not wear loose cloth-

ing or jewelry. Keep your hair, clothing

and gloves away from moving parts.

Loose clothes, jewelry or long hair can be

caught in moving parts.

If devices are provided for the connec-

tion of dust extraction and collection

facilities, ensure these are connected

and properly used. Use of these devices

can reduce dust-related hazards.

WARNING

GENERAL SAFETY RULES

DM 2610925781 5-05.qxd 5/12/05 10:31 PM Page 2

Keep handles dry, clean and free from oil

and grease. Slippery hands cannot safely

control the power tool.

Power tool use and care

Do not force the power tool. Use the cor-

rect power tool for your application. The

correct power tool will do the job better and

safer at the rate for which it was designed.

Do not use the power tool if the switch

does not turn it on and off. Any power tool

that cannot be controlled with the switch is

dangerous and must be repaired.

Disconnect the plug from the power

source and/or the battery pack from the

power tool before making any adjust-

ments, changing accessories, or storing

power tools. Such preventive safety meas-

ures reduce the risk of starting the power

tool accidentally.

Store idle power tools out of the reach of

children and do not allow persons unfa-

miliar with the power tool or these

instructions to operate the power tool.

Power tools are dangerous in the hands of

untrained users.

Maintain power tools. Check for mis-

alignment or binding of moving parts,

breakage of parts and any other condi-

tion that may affect the power tools oper-

ation. If damaged, have the power tool

repaired before use. Many accidents are

caused by poorly maintained power tools.

Keep cutting tools sharp and clean.

Properly maintained cutting tools with sharp

cutting edges are less likely to bind and are

easier to control.

Use the power tool, accessories and tool

bits etc., in accordance with these

instructions and in the manner intended

for the particular type of power tool, tak-

ing into account the working conditions

and the work to be performed. Use of the

power tool for operations different from

those intended could result in a hazardous

situation.

Use clamps or other practical way to

secure and support the workpiece to a

stable platform. Holding the work by hand

or against your body is unstable and may

lead to loss of control.

Service

Have your power tool serviced by a quali-

fied repair person using only identical

replacement parts. This will ensure that the

safety of the power tool is maintained.

Develop a periodic maintenance sched-

ule for your tool. When cleaning a tool be

careful not to disassemble any portion of

the tool since internal wires may be mis-

placed or pinched or safety guard return

springs may be improperly mounted.

Certain cleaning agents such as gasoline,

carbon tetrachloride, ammonia, etc. may

damage plastic parts.

SAFETY RULES FOR ROTARY TOOL

Hold tool by insulated gripping surfaces

when performing an operation where the

cutting tool may contact hidden wiring or

its own cord. Contact with a "live" wire will

make exposed metal parts of the tool "live"

and shock the operator.

Use clamps or other practical way to

secure and support the workpiece to a

stable platform. Holding the work by hand

or against your body is unstable and may

lead to loss of control.

Accessories must be rated for at least the

speed recommended on the tool warning

label. Wheels and other accessories run-

ning over rated speed can fly apart and

cause injury.

If cutting into existing walls or other blind

areas where electrical wiring may exist is

unavoidable, disconnect all fuses or circuit

breakers feeding this worksite.

Do not operate the flexible shaft with a

sharp bend. Over bending the shaft can

generate excessive heat on the jacket or

hand piece. The recommended minimum is

6" radius.

Always disconnect the power cord from

the power source before making any

adjustments or attaching any acces-

SAVE THESE INSTRUCTIONS

DM 2610925781 5-05.qxd 5/12/05 10:31 PM Page 3

Specyfikacje produktu

Marka:	Dremel
Kategoria:	Maszyna do śrub
Model:	300 Series

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Dremel 300 Series, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje Maszyna do śrub Dremel

Dremel 400 XPR Instrukcja

15 Września 2024

Dremel 300 Series Instrukcja

13 Września 2024

Instrukcje Maszyna do śrub

Najnowsze instrukcje dla Maszyna do śrub

Makita DHP448 Instrukcja

12 Października 2024

Black & Decker HP9012 Instrukcja

10 Października 2024

Bosch GSB 18V-65 Professional Instrukcja

9 Października 2024

Bosch GDX 18V-285 Professional Instrukcja

9 Października 2024

Hazet 9013 LGTT Instrukcja

9 Października 2024

Cleco 19TTA05Q Instrukcja

9 Października 2024

Cleco 30EFN30F1 Instrukcja

9 Października 2024

Cleco 30EAN28FA3 Instrukcja

9 Października 2024

Cleco 30EAR12S131 Instrukcja

9 Października 2024

Cleco 19TTS03Q Instrukcja

9 Października 2024