Instrukcja obsługi Donexon varmo TZ eco

Donexon Niesklasyfikowane varmo TZ eco

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Donexon varmo TZ eco (8 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 7 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/8

DONEXON

varmo TZ eco

SKU: DONEVARMOTZECO

Quickstart

This is a

secure

HVAC-Thermostat Europefor . To run this device please insert fresh batteries. Please make sure the internal battery is fully2 * AA 1,5V

charged.

1. Start Inclusion mode of your primary Z-Wave Controller.

2. Press the Boost-Button.varmo TZ eco will show the assigned Node ID.

Important safety information

Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer,

distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this

equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.

What is Z-Wave?

Z-Wave is the international wireless protocol for communication in the Smart Home. This device is suited for use in the region mentioned in the Quickstart section.

Z-Wave ensures a reliable communication by reconfirming every message (

two-way communication

) and

every mains powered node can act as a repeater for other nodes (

meshed network

) in case the receiver is

not in direct wireless range of the transmitter.

This device and every other certified Z-Wave device can be used together with any other certified

Z-Wave device regardless of brand and origin as long as both are suited for the same frequency range.

If a device supports it will communicate with other devices secure as long as thissecure communication

device provides the same or a higher level of security. Otherwise it will automatically turn into a lower level

of security to maintain backward compatibility.

For more information about Z-Wave technology, devices, white papers etc. please refer to www.z-wave.info.

Product Description

The varmo TZ eco radiator valve regulates your radiator with energy-saving Z-Wave wireless standard. Thus, you can add a component to your Z-Wave Smart

Home network.Thanks to the FLiRS (Frequently Listening Receiver Slave), the heating valve responds to incoming commands without any major delays, for

example changing the temperature.Design covers are available in various colors, so you can change them according to your wishes and interior design.The varmo

TZ eco radiator valve is easy to operate, has an orange backlit display and an extra large temperature display. Heating periods are programmable, the daily and

weekly times are individually programmable and the valve detects when a window is open. The manual adjustment is of course possible at any time.In addition,

the valve has a child safety lock and various security levels, a frost and lime protection function and fits on many common radiator valves.The display can be

rotated 180 degrees.

Prepare for Installation / Reset

Please read the user manual before installing the product.

In order to include (add) a Z-Wave device to a network it Please make sure to reset the device into factory default. You can domust be in factory default state.

this by performing an Exclusion operation as described below in the manual. Every Z-Wave controller is able to perform this operation however it is recommended

to use the primary controller of the previous network to make sure the very device is excluded properly from this network.

Reset to factory default

This device also allows to be reset without any involvement of a Z-Wave controller. This procedure should only be used when the primary controller is inoperable.

Remove batteries. Press and hold boost button. While still holding boost button insert batteries. The LCD shows RES. Release boost button. To perform the

factory reset press boost button.

Safety Warning for Batteries

The product contains batteries. Please remove the batteries when the device is not used. Do not mix batteries of different charging level or different brands.

Installation

Mounting the Donexon TZ eco Thermostat

After adding the Donexon TZ eco Thermostat to a network, it is ready to be installed on the radiator. The LCD shows INS. Do not press the boost button yet.

Installation at the radiator without Adapter

Installation at the radiator with Adapter

Mechanical Installation

Press the boost button to start mechanical installation.

Unmounting the Donexon TZ eco Thermostat

Inclusion/Exclusion

On factory default the device does not belong to any Z-Wave network. The device needs to be

added to an existing wireless network

to communicate with the

devices of this network. This process is called .Inclusion

Devices can also be removed from a network. This process is called . Both processes are initiated by the primary controller of the Z-Wave network. ThisExclusion

controller is turned into exclusion respective inclusion mode. Inclusion and Exclusion is then performed doing a special manual action right on the device.

Inclusion

Press the Boost-Button.varmo TZ eco will show the assigned Node ID.

Exclusion

Press and hold the boost button of the varmo TZ eco for at least 5 seconds.

Product Usage

Buttons:

Boost-Taste Led‘s