Instrukcja obsługi DLS 224

DLS głośnik 224

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla DLS 224 (4 stron) w kategorii głośnik. Ta instrukcja była pomocna dla 11 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/4

PERFORMANCE SERIES

CAR AUDIO SPEAKERS

WELCOME

Thank you for buying a DLS Performance series spea-

ker.

This manual will show you how to do a correct installa-

tion. Please read the entire manual before beginning the

installation.

Install the speakers yourself if you feel confident with our

instructions and if you have the proper tools. However if

you feel unsure, turn over the installation job to someone

better suited to it.

INSTALLATION

Mount the speakers in the door or in the dashboard of

your car. Normally they will fit in the facory pre-made

mounting holes. If you want an improved sound reinforce

with a baffle of MDF-board or similar. An installation high

up on the door side is to be prefered. An alternative in-

stallation is in so called kick panels down on each side of

the floor with the speakers facing up- and inwards

towards the listener.

For two- or three way speaker systems with separate

tweeter an installation of the tweeter close to the bass/

mid element is to be prefered. The tweeter can also be

installed on the dash-board, or recessed in the door with

the accessories in the tweeter box.

It is important to fasten the speakers properly in order to

avoid bad sound or rattling.

For speakers with separate filters in boxes or similar it is

vital that they are attached properly to the interior of the

vehicle to avoid rattling. Don´t place them close to the

internal wiring of the car, this can cause interference.

Avoid to install filter boxes in the door sides because

they can easily be broken because of rattling or

moisture. Make sure the cables don´t get jammed

causing a short circuit to ground. This can damage the

output circuits of the head unit or amplifier.

All models except for 257 and 457 comes with grilles.

The tweeter installation for kits with separate tweeter is

described on last page, or in the instruction sheet

coming with the tweeters.

SPEAKER ENCLOSURES

If you want to install the speaker in an enclosure the nor-

mal size for a sealed type is:

4” (10 cm) speakers : 2-4 liters

5,25” (13 cm) speakers : 6-8 liters

6,5” (16,5 cm) speakers : 10-12 liters

8” (20 cm) speakers : 15-20 liters

6 x 9” speakers : 15-20 liters

These volumes are only a guideline, they can vary

between different speakers. Contact your local DLS

dealer for more exact information about your specific

speaker.

124, 125,126,1269

224, 225, 226, 257, 269

424, 425, 426, 457, 428

960, 962

B5A, B6A, C4, C5A, C6A, C36

SPEAKERS 124, 125, 126 & 1269

DLS 124, 125 & 126 & 1269 are coaxial speaker with

integrated filter.

COAXIAL SPEAKERS 224, 225, 226, 257, 269 &

960

The 224, 269 and 960 models have an integrated tweeter

filter. DLS 225, 226 and 257 have a separate cable filter

wrapped in plastic cover. Inside the cover there is both a

lowpass filter for the woofer and a highpass filter for the

tweeter. On next page you can see how to connect the

filter.

The filters must be used, if you connect without them

the sound becomes bad and you will destroy the

tweeter.

COAXIAL SPEAKERS 424, 425, 426, 457, 428 &

962.

These speakers have a separate filter box with lowpass

filter for the woofer and a highpass filter for the tweeter.

The tweeter level can be adjusted inside the filter box in

two steps, high and low. Install the filter box in a dry place.

On next page you can see how to connect the filter.

The filters must be used, if you connect without them

the sound becomes bad and you will destroy the

tweeter.

TWO-WAY SYSTEMS B5A & B6A

These systems have a separate tweeter. The filters are

separate lowpass and highpass in small plastic boxes with

selectable tweeter level in two steps. The bass/mid spea-

ker driver uses the new DLS EFR technology for improved

sound quality.

On next page you can see how to connect the filter.

The filters must be used, if you connect without them

the sound becomes bad and you will destroy the

tweeter.

TWO/THREE-WAY SYSTEMS C4, C5A, C6A & C36

The 2-way systems have a separate tweeter. The filters

are separate lowpass and highpass in small plastic boxes

with selectable tweeter level in three steps inside. C36 is

a 3-way system with a filter box where you can connect a

woofer, a midrange speaker and a tweeter. The tweeter

level can be adjusted in three steps inside the filter box.

On next page you can see how to connect the filter.

The filters must be used, if you connect without them

the sound becomes bad and you will destroy the

tweeter.

Model Woofer Mid Tweeter Nom. Max Sensi- Magnet Inst. Mounting Crossover

power power tivity size depth hole

125 10 cm / 4” 16 mm / 0,63” 50 W 80 W 93 dB 70 mm / 2,75” 45 mm / 1,7” 102 mm ” 4” Integrated

125 13 cm / 5,25” 16 mm / 0,63” 50 W 80 W 92 dB 70 mm / 2,75” 50 mm / 1,97” 120 mm / 4,72” Integrated

126 16,5 cm / 6,5” 16 mm / 0,63” 50 W 80 W 92 dB 80 mm / 3,15” 28 mm / 2,28” 145 mm / 5,7” Integrated

1269 6 x 9” 50 mm / 2” 60 W 120 W 92 dB 80 mm / 3,15” 75 mm / 3” 150x220 mm / 5,9x8,7” Integrated

224 10 cm / 4” 16 mm / 0,63” 50 W 80 W 93 dB 70 mm / 2,75” 50 mm /1,97” 102 mm / 4” Integrated

225 13 cm / 5,25” 16 mm / 0,63” 50 W 80 W 92 dB 80 mm / 3,15” 54 mm / 2,12” 120 mm / 4,72” Integrated

226 16,5 cm / 6,5” 16 mm / 0,63” 50 W 80 W 92 dB 80 mm / 3,15” 52 mm / 2” 145 mm / 5,7” Integrated

269 6 x 9” 50 mm 16 mm / 0,63” 80 W 120 W 92 dB 100 mm / 3,94” 80 mm / 3,15” 150x220 mm / 5,9x8,7” Integrated

257 5 x 7” 16 mm / 0,63” 50 W 80 W 92 dB 80 mm / 3,15” 60 mm / 2,36” 130 x 185 mm / 5,1x7,3” Integrated

424 10 cm / 4” 20 mm / 0,8” 50 W 80 W 94 dB 80 mm / 3,15” 58 mm / 2,28” 102 mm / 4” Separate box

425 13 cm / 5,25” 20 mm / 0,8” 60 W 90 W 93 dB 90 mm / 3,54” 61 mm / 2,4” 117 mm / 4,6” Separate box

426 16,5 cm / 6,5” 20 mm / 0,8” 60 W 90 W 94 dB 100 mm / 4” 62 mm / 2,44” 145 mm / 5,7” Separate box

428 20 cm / 8” 25 mm / 1” 80 W 120 w 94 dB 105 mm / 4,1” 87 mm / 3,43” 185 mm / 7,282 Separate box

457 5 x 7” 20 mm / 0,8” 60 W 90 W 93 dB 100 mm / 4” 58 mm / 2,28” 130 x 185 mm / 5,1x7,3” Separate box

960 6 x 9” 50 mm 20 mm / 0,8” 80 W 120 W 93 dB 100 mm / 4” 83 mm / 3,27” 150x220 mm / 5,9x8,7” Integrated

962 6 x 9” 25 mm / 0,8” 80 W 120 W 93 dB 100 mm / 4” 83 mm / 3,27” 150x220 mm / 5,9x8,7” Separate box

B5A* 13 cm / 5,25” 16 mm / 0,63” 50 W 80 W 91 dB 80 mm / 3,15” 63 mm / 2,48” 117 mm / 4,6” Separate LP/HP

B6A* 16,5 cm / 6,5” 16 mm / 0,63” 50 W 80 W 91 dB 80 mm / 3,15” 63 mm / 2,48” 146 mm / 5,75” Separate LP/HP

C4 10 cm / 4” 20 mm / 0,8” 50 W 80 W 92 dB 70 mm / 2,75” 58 mm / 2,28” 102 mm / 4” Cable filter

C5A 13 cm / 5,25” 20 mm / 0,8” 50 W 80 W 93 dB 80 mm / 3,15” 60 mm / 2,36” 120 mm / 4,72” Separate boxes

C6A 16,5 cm / 6,5” 20 mm / 0,8” 60 W 90 W 93 dB 80 mm / 3,15” 63 mm / 2,48” 156 mm / 5,75” Separate boxes

C36 16,5 cm / 6,5” 4” 20 mm / 0,8” 60 W 90 W 93 dB 80 / 70 mm 63 / 58 mm 146 / 102 mm Separate boxes

* Speakers using the DLS EFR technology for improved sound quality.

SPEAKER FACTS FOR DLS PERFORMANCE SERIES

RUNNING-IN PERIOD

Allow the speakers to play for at

least 15-20 hours. After this time the

performance is correct.

Speaker

connection and

tweeter level

select:

Use the red, blue and black

cables to connect between

the filter box and speaker

terminal. Note the speaker

terminal colour marking.

Select tweeter level by

moving the jumper inside

the filter box between high /

low. Make your own tests

for best result.

Filter installation and connection of coaxial

speakers 424, 425, 426 and 457

Red +

Blue +

Black -

INPUT WOOFER TW

+ - + - + -

coaxial

2-way crossover

Car stereo or

amplifier

coaxial

2-way crossover

Green

Red

Yellow

Tweeter level

Green to red=high

Green to yellow=low

Red +

Blue +

Black -

Car stereo or

amplifier

Filter installation and connection of coaxial

speakers 962 and 428

On the cable filter box

without screw terminals

the level select is made

on the outside by

connecting the green

cable to either the red

or yellow one coming

out from the box.

Tweeter level select:

High level: Connect

green and red wire.

Low level: Connect

green and yellow wire.

FILTER/CROSSOVER INSTALLATIONS

Car stereo or

amplifier

CONNECTION OF SPEAKERS

For speakers with integrated filters

you just connect like this. Make sure

the polarity is correct for both left

and right side.

SPEAKER PHASING

To be sure to have the correct speaker polarity (phase) you can

check this by using a 1,5 Volt battery.

Connect a cable from the battery plus-pole to the speaker plus,

and a cable from the battery minus to the speaker minus.

If the speakers are correctly connected the speaker cone should

move outwards on both right and left channel.

This check must be made on the cables going from the speakers,

to the output terminals of your car stereo or amplifier.

+--

FILTER/CROSSOVER INSTALLATIONS

Cable filter

High pass

(red)

Red + Black -

Yellow

Red

Cable filter

Low pass

(blue)

Black - Blue +

Car stereo or

amplifier

Filter installation B5A and B6A

Tweeter

level select:

For High level

connect yellow

and red wire.

Disconnect for

Low level

Tweeter

Cable filter

High pass

(yellow)

Transp - Red +

Yellow

Red

Blue

High pass

Cable filter

Low pass

(green)

Black - Red +

Low pass

Car stereo or

amplifier

Filter installation C5A

Black - Blue +

Black - Red +

Tweeter level select:

High level: Connect yellow

and red wire.

Mid level: Connect yellow

and blue wire.

Low level: All circuits open.

Black - Red + Black - Red +

Black - Red +

Cable filter

High pass

(yellow)

Transp - Red+

High pass

Cable filter

Low pass

(green)

Black - Red +

Low pass

Car stereo or

amplifier

Filter installation C4

Tweeter

Tweeter level

select:

High level: Connect

Red and yellow wire.

Low level:

Disconnect red and

yellow wire.

Black - Red +

Head unit / amp.

Mid-

bass

Red +

+ IN - + TW - + MID - + WF -

Midrange

Red +

Tweeter

Red +

+ IN - + TW - + MID - + WF -

OUT

-2 dB

-4 dB

CONNECT/DISCONNECT THE MIDBASS, JUMPER J1:

If you want to run the midbass driver with an active crossover

using a separate amplifier, and run the midrange and tweeter

through the passive filter box, you must move the jumper J1 to

position OUT. The normal position for this jumper is IN.

TWEETER LEVEL SELECT, JUMPER J2:

The tweeter level can be selected in three step by moving jum-

per J2 between 0, -2dB or -4dB. The lowest tweeter level is

achieved in the -4dB position.

Filter installation 225, 226 and 257

Filter installation and connection of C36

Low pass

High pass

Car stereo or

amplifier

Cable filter

Black - Red +

Connect the three

cables from the

speaker terminals to

the filter according to

drawing. Black cable

is common minus for

both tweeter and

woofer.

Black - Blue + Red+

IN TWEETER

+ - + -

Tweeter

Head unit / amp

+ -

Woofer

IN WOOFER

+ - + -

Silver/red

Silver

Black/blue

Black

Tw level

Hi Mid Lo

Tweeter level select:

Select tweeter level by moving the

jumper inside the filter box between

high, mid or low. Make your own

tests for best result.

Filter installation C6A

Yellow

Red

Specyfikacje produktu

Marka:	DLS
Kategoria:	głośnik
Model:	224

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z DLS 224, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje głośnik DLS

DLS 224 Instrukcja

26 Września 2024

Instrukcje głośnik

Najnowsze instrukcje dla głośnik

Elipson Horus 10C Instrukcja

14 Marca 2025

Elipson INF IW8 Instrukcja

14 Marca 2025

Elipson INF IW6 Instrukcja

14 Marca 2025

Elipson BS50 Tribute Instrukcja

14 Marca 2025

Elipson Heritage XLS7 Instrukcja

14 Marca 2025

Elipson Horus 8S Instrukcja

14 Marca 2025

Elipson Bell 4 Instrukcja

14 Marca 2025

Elipson Infinite 14 Instrukcja

14 Marca 2025

Elipson INF IC8 Instrukcja

14 Marca 2025

Elipson Infinite 8 Instrukcja

14 Marca 2025