Instrukcja obsługi Dimplex RX03002

Dimplex Niesklasyfikowane RX03002

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Dimplex RX03002 (3 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 5 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/3
Contact Details
Pleasenotethat some contact ofthe details on 
thisPDFdocumentmaynotbe current.
Pleaseuse  the following detailsifyouneedto
contactus:
Telephone:0844 879 3588
Email:customer.services@gdcgroup.co.uk
The widecustomer alsosupportsection websiteofour  features a
rangeof ofinformationwhichmaybe use availabletoyouandis 
24 ahours day.Itincludes:
• Operating  and installation instructions
• Easy   ‘How to use’ guides for storage heaters
• Service  and repairs
• Wheretobuyourproducts
• Literature downloads
• Heating  requirement calculator
 ‐Visit www.dimplex.co.uk/support
A division of GDC Group Ltd
Millbrook House Grange Drive Hedge End Southampton SO30 2DF
www.dimplex.co.uk
Re
g
istered No: 1313016 En
g
land
VAT GB 287 1315 50004
EEE Producer Registration Number –
WEE/GE0057TS
Paper from sustainable sources
Mains Borne Signalling Receiver Unit
Model: RX03002
Installation and
Operating Instructions
85932 Issue 1
Dimensions
(millimetres)
THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR FUTURE REFERENCE
GENERAL DESCRIPTION
MBS Receiver for Dimplex DuoHeat Radiators. To be used in conjunction with RX010007 MBS programmer.
(Please refer to RX010007 Operating Instructions).
RX010007 provides central control for up to 20 radiators across 2 zones, using existing wiring to communicate to
the radiator(s). One RX03002 receiver is required for each radiator. The receiver accepts the MBS signal and
converts it to a pilot wire output, automatically switching the radiator(s) between comfort and set back modes in
accordance with the preset programme. Each receiver can manually override the comfort and set back settings
sent by the central control program for the radiator(s) if required.
INSTALLATION
Wall mounting
Firstly decide where you are going to install
the receiver, in conjunction with the clear-
ance of minimum 50mm shown in Fig. 2.
Screw the receiver to the wall using one of
the 4 bracket types or the adhesive pads.
Fig. 2
Fig. 1
Height Width Depth
171mm 50mm 25mm
Glen Dimplex UK Limited
Millbrook House
Grange Drive
Hedge End
Southampton
Hampshire SO30 2DF
UK customer helpline (8.00AM - 6.00PM Mon-Fri; 8.30AM-1.00PM Sat)
Customer Help Line Tel: 0870 7270 101
Fax: 0870 7270 102
e-mail: customer.services@glendimplex.com
Republic of Ireland Tel: 01 842 4833
This appliance complies with the European Standards EN 60 335-1, EN 60 335-2-61, EN 61000-3-2,
EN 61000-3-3, EN 55014 and EN55104 for Safety & Electromagnetic Compatibility.
These standards cover the requirement of the EMC Directives 89/336 & 73/23
Wiring
IMPORTANT – ISOLATE BOTH MAINS SUPPLIES
TO THE RADIATOR BEFORE INSTALLING
The receiver unit should be connected to the DuoHeat radiator
by connecting the pilot wires from the heater and MBS receiver
unit together.
Connect the brown (L) and blue (N) wires from the RX03002
MBS receiver unit and the DuoHeat radiator to the mains
supply. Connect the black wire (Pilot) from the receiver unit
to the black wire from the DuoHeat radiator front panel using
a through crimp.
Make the connections such that the MBS receiver will be
isolated together with the direct acting power supply to the
heater when the fused spur is switched off.
Switch on the mains supply and the receiver is now ready to
be configured.
Configuration
Set the MBS central controller RX010007 to the configuration
mode. (Please refer to section 5 of RX010007 instructions)
The RX03002 receives information from the central controller
unit and transmits it to the Duo heat radiator.
You must now configure the MBS receiver with the MBS
central controller (RX010007)
Press the key briefly and the
green ‘OK’ light will flash steady.
The receiver is now configured.
If the green ‘OK’ light flashes slowly then the receiver is not
configured. Press and hold the key for 10 seconds until
the green ‘OK’ light flashes slowly then press again briefly,
the green ‘OK’ light should flash steady and the receiver is
now configured.
Operation
Receiver modes are explained in the table below:
Table 1
Manual Override
Each RX03002 MBS receiver can manually override the
comfort and set back settings sent by the RX010007 MBS
central controller. ‘Frost protection’ and the ‘Off’ setting
cannot be overridden by the receiver only by the central
control unit. Room temperature is set by the controls on the
radiator. (See Table 2).
Table 2
Override cancelling;
If the program has been manually overridden at by the
MBS receiver, the MBS controller unit will automatically
change the setting at the start of the next program.
To manually change the setting again press key on
receiver
Cleaning
The outside of the receiver should be wiped over with a soft
damp cloth and then dried. Do not use detergents or abrasives.
After Sales Service
Your Dimplex receiver is guaranteed for one year from date
of purchase. We undertake to exchange or repair free of
charge within this period, any part found to be defective.
Should you require after sales service, please get in touch
with the supplier through whom you purchased the product,
or contact Dimplex Customer Service.
Please do not initially return a faulty product, or part of, to us
as this may result in transit damage and/or a delay in
providing service. Let us know your difficulty by quoting the
model number and we will take the appropriate action.
Controller Mode Heater Function
Comfort Radiator functions at thermostat setting
Setback Radiator controlled at pre-set
minimum setting (approx.17°C)
Frost Protection No input charge accepted. Radiator
maintains approx.5°C
Off No heat output
Program in
progress
Mode after
pressing the
key
Corresponding
flashing light
Comfort Background
Background Comfort
Frost protection Comfort
Off Comfort

Specyfikacje produktu

Marka: Dimplex
Kategoria: Niesklasyfikowane
Model: RX03002

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Dimplex RX03002, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Niesklasyfikowane Dimplex

Dimplex

Dimplex GDDEU30 Instrukcja

2 Października 2024
Dimplex

Dimplex OCR20Tie Instrukcja

2 Października 2024
Dimplex

Dimplex OPH13 Instrukcja

30 Września 2024
Dimplex

Dimplex ALM20E Instrukcja

28 Września 2024
Dimplex

Dimplex TDTR175C Instrukcja

27 Września 2024
Dimplex

Dimplex BYP20 Instrukcja

22 Września 2024
Dimplex

Dimplex MZT20E Instrukcja

20 Września 2024
Dimplex

Dimplex MZT20BL-E Instrukcja

20 Września 2024
Dimplex

Dimplex GLN20BR Instrukcja

19 Września 2024
Dimplex

Dimplex Optiflame 3D BMR20CH3D Instrukcja

18 Września 2024

Instrukcje Niesklasyfikowane

Najnowsze instrukcje dla Niesklasyfikowane

Black Diamond

Black Diamond BD1121530000ALL1 Instrukcja

15 Października 2024
Husqvarna

Husqvarna K 970 SmartGuard Instrukcja

15 Października 2024
Stihl

Stihl HT 70 Instrukcja

15 Października 2024
Ernesto

Ernesto H14270 Instrukcja

15 Października 2024
Uniden

Uniden BT MIC KIT Instrukcja

15 Października 2024
Vaude

Vaude Omnis Bike 26 Instrukcja

15 Października 2024
ART

ART ProChannel II Instrukcja

15 Października 2024
Aukey

Aukey DR02J Instrukcja

15 Października 2024
Master Lock

Master Lock 653EURD Instrukcja

15 Października 2024
Roland

Roland FR-18 Diatonic Instrukcja

15 Października 2024