Instrukcja obsługi Dimplex RFREC

Dimplex Niesklasyfikowane RFREC

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Dimplex RFREC (2 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 6 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/2

230/240V AC

RF Controller Unit: Controller &

Receiver

Installation and Operating Instructions

RFTS234P01 Issue 0

Fig. 1

IMPORTANT : THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR FUTURE REFERENCE

Important Safety Advice

When using electrical appliances, basic precautions should

always be followed to reduce the risk of fire, electrical

shock, and injury to persons, including the following:

This product is splash proof to IP24 standard and may be

used in bathrooms in Zones 2 & 3 only, however not in the

immediate vicinity of baths, showers, water connections,

wash basins or swimming pools.

This unit must only be used on an A.C Mains supply of 230/

240V with products up to a maximum of 2kW.

Ensure that supply cables to the product are of adequate

current carrying capacity.

This product is used to control separate heating appliances.

Please note the safety guidelines of the controlled product

must be adhered to at all times.

General

The RF Controller Unit is an electronic device which provides wireless

room temperature control for use with heating appliances. The Unit can

be used to control multiple heating appliances. Note: Each appliance

requires a Receiver Unit.

The Unit can be used in conjunction with heating appliances with a

maximum heating capacity of 2kW. The Controller Unit cannot be used

with a Quartz Halogen heater without a suitable in-line contactor.

The RF Controller Unit consists of a Controller and a Receiver. Both the

Controller and Receiver are wall mounted. The Controller provides

wireless room temperature control. Control of the product is achieved

via an RF signal from the Controller to Receiver which is wired direct to

the heating appliance. This eases installation. To quickly heat a cold room

the Controller incorporates a ‘Boost’ function which overrides the

thermostatic control for a set period of time.

Installation

Before undertaking installation work, ensure the electricity supply is

disconnected from any relevant fixed wiring.

·All wiring should be carried out by a qualified electrician in accordance

with the current IEE wiring regulations.

·Both the Controller and Receiver units are designed to be fitted to a

standard single BS backing box with a depth of at least 25mm. The

backing box (not supplied) should already be recessed into the wall.

·Ensure the top and bottom lugs (if fitted) of metal backing boxes are

removed prior to installation.

·The location of the Controller is important. The Controller is fitted with

a room temperature sensing device and therefore will not function

correctly if positioned too close to a heat source or draught area.

Please ensure the Controller is not located above or within 500mm of

a heat source or draught.

Controller

a) Remove screw ‘x’ from the underside of the Controller unit - see

Fig. 2.

b) The front facia is held in place by clips at the top. It must be

removed by lifting the top of the facia upwards and then outwards

- see Fig. 2.

c ) Connect the fixed wiring of the premises from the back box to the

clearly marked terminals on the Controller - see Fig. 3.

d) Secure the Controller to the backing box using the screws provided

(located on rear moulding) - see Fig. 2.

Note: The Controller front facia should not be refitted until the unit has

been programmed - see ‘Unit Set-Up’.

Controller - see Fig. 2

1. Standby button/thermostat control knob

2. ‘ON’ Indicator

3. ‘HEAT’ Indicator

4. ‘BOOST’ Indicator

5. ‘BOOST’ button

6. ‘TRANSMIT’ button

Controller Wiring - see Fig. 3

Fig. 3

Fig. 2

95 47

95 38

Controller Receiver

230/240V AC

NLN

HEATING

APPLIANCE

Receiver

a) If the heating appliance to be used in conjunction with the Controller

is fitted with a plug, please remove the plug and strip the wires to the

appropriate length.

b) Remove the front facia of the Receiver - see steps ‘a’ and ‘b’ in

‘Controller’ The cable clamp on the rear of the Receiver should then

be removed.

c ) The cable of the heating appliance is fed through an opening on the

underside of the Receiver unit - see Fig. 5.

d) The cable from the heating appliance is then wired to the terminal

block labelled (out). Please ensure the wires are connected in

accordance with the marked terminals - see Fig. 5.

e) The cable from the heating appliance is then clamped to the rear of

the Receiver unit using the cable clamp previously removed.

f ) Connect the fixed wiring of the premises from the backing box to the

clearly marked terminals on the Receiver unit (see Fig. 5). Please

ensure that the unit is earthed to the backing box.

g) Secure the Receiver to the back box using the screws provided

(located on rear moulding) - see Fig. 4.

Note: The Receiver front facia should not be refitted until the unit has

been set up (see ‘Unit Set-Up’).

Receiver - see Fig. 4

1. ‘HEAT’ Indicator

2. ‘AUTO’ Indicator

3. ‘OVERRIDE’ button

4. ‘TRANSMIT’ button

Receiver Wiring - see Fig. 5

Unit Set-Up

The Receiver must be synchronised to suit your individual Controller.

Each Controller can be used to control multiple heating appliances.

1. Remove the front facias from both the Controller and Receiver units

(see ‘Installation’).

2. Ensure both the Controller and Receiver(s) are powered up. To

activate the Controller press the standby button see ‘1’ in Fig. 2.

When activated, the ‘ON’ (Green) light will illuminate.

3. Press the ‘TRANSMIT’ button on the Receiver. The Receiver goes

into synchronise mode. This is indicated by both the ‘AUTO’ (yellow)

and the ‘HEAT’ (Red) lights flashing. If more than one Receiver is to

be controlled by a single Controller all Receivers must similarly be put

into synchronise mode. Each Receiver will remain in synchronise

mode for approximately one minute.

4. With the Receiver(s) in the synchronise mode the ‘TRANSMIT’ button

on the Controller is then pressed. This puts the Controller in

synchronise mode, this is indicated by the Controller ‘HEAT’ (red)

and ‘BOOST’ (blue) lights flashing. The Controller will remain in

synchronise mode for approximately ten seconds.

5. The Receiver will automatically go into auto mode once a signal has

been received from the Controller. The Controller is ready once the

‘AUTO’ (yellow) light is lit on the Receiver.

6. The front facias should then be replaced on both the Controller and

Receiver, ensuring the bottom screw is replaced.

Operating Instructions

The Unit controls the room temperature by interrupting the power supply

to the appliance, therefore ensure that the appliance is always switched

on and its thermostat (if any) is always set to its maximum position. If the

Controller is in standby mode all three lights will be off.

· Power up the Controller by pressing the standby button (control knob).

The ‘ON’ (green) light on the Controller and the ‘AUTO’ (yellow) light on

the Receiver should illuminate. The ‘AUTO’ light on the Receiver

indicates that the controller is functioning automatically.

· Adjust the temperature control knob between the ‘MAX’ and ‘MIN’

positions to the desired temperature.

· If the room temperature is below the set desired temperature the

controller will switch the appliance ‘ON’. When the appliance is ‘ON’

the ‘HEAT’ (red) light on the Controller and Receiver units will be

illuminated.

· The Boost function will override the Controller and run the appliance

constantly for 30minutes. The Boost mode can be activated by pressing

the ‘BOOST’ button. The Controller in Boost mode will be indicated by

all three lights on the Controller being illuminated. Boost mode can be

de-activated by pressing the ‘BOOST’ button again.

Note: If the ‘AUTO’ (yellow) light on the Receiver is flashing the control

unit is in fail mode (a link failure has occurred between the Controller and

Receiver). If this occurs the appliance can be operated in a manual

mode. To activate manual mode the front cover of the Receiver must be

removed (see ‘Installation’). The ‘OVERRIDE’ button will put the Controller

in manual mode and the appliance will be switched ‘ON’, this is indicated

by the ‘HEAT’ (Red) light On and the ‘AUTO’ (yellow) light Off on the

Controller.

If a link failure has occurred, the Controller and Receiver must be paired

again (see ‘Unit Set-Up’). If this is not successful please contact your

service agent.

Cleaning

WARNING: ALWAYS PLACE THE CONTROLLER IN STAND BY MODE

BEFORE CLEANING.

Do not use detergents, abrasive cleaning powders or polish of any kind

on the controller.

Wipe with a dry cloth to remove dust and a damp cloth (not wet) to clean

off stains. Be careful not to allow moisture into the heater.

Recycling

For electrical products sold within the European Community.

At the end of the electrical products useful life it should not be

disposed of with household waste. Please recycle where

facilities exist. Check with your Local Authority or retailer for

recycling advice in your country.

After sales service

Should you require after sales service or should you need to purchase

any spares, please contact the retailer from whom the appliance was

purchased. Please do not return a faulty product to us in the first instance

as this may result in loss or damage and delay in providing you with a

satisfactory service. Please retain your receipt as proof of purchase.

Fig. 4

Fig. 5

Specyfikacje produktu

Marka:	Dimplex
Kategoria:	Niesklasyfikowane
Model:	RFREC
Kolor produktu:	Black,White
Typ kontroli:	obrotowy
Wbudowany wyświetlacz:	Nie
Położenie urządzenia:	Wbudowany
Napięcie wejściowe AC:	230 V
Wysokość produktu:	50 mm
Szerokość produktu:	580 mm
Głębokość produktu:	510 mm
Szerokość opakowania:	670 mm
Wysokość opakowania:	110 mm
Głębokość opakowania:	560 mm
Rodzaj płyty grzejnej:	Gaz
Liczba palników/stref gotowania:	4 stref(y)
Liczba palników:	4 stref(y)
Liczba płytek elektrycznych:	0 stref(y)
Zapłon elektroniczny:	Tak
Pozycja palnika/strefy grzewczej 1:	Lewy tylny
Źródło zasilania palnika/strefy grzewczej 1:	Gaz
Typ palnika/strefy grzewczej 1:	Regularny
Moc palnika/strefy grzewczej 1:	1750 W
Pozycja palnika/strefy grzewczej 2:	Lewy przód
Źródło zasilania palnika/strefy grzewczej 2:	Gaz
Typ palnika/strefy grzewczej 2:	Duży
Moc palnika/strefy grzewczej 2:	3000 W
Pozycja palnika/strefy grzewczej 3:	Prawy tył
Źródło zasilania palnika/strefy grzewczej 3:	Gaz
Typ palnika/strefy grzewczej 3:	Regularny
Moc palnika/strefy grzewczej 3:	1750 W
Pozycja palnika/strefy grzewczej 4:	Prawy przód
Źródło zasilania palnika/strefy grzewczej 4:	Gaz
Typ palnika/strefy grzewczej 4:	Wrzenie
Moc palnika/strefy grzewczej 4:	1000 W
Kształt strefy gotowania 1:	Okrągły
Strefa gotowania 3 kształt:	Okrągły
Strefa gotowania 4 kształt:	Okrągły
Kształt strefy gotowania 2:	Okrągły
Normalny palnik:	- W