Instrukcja obsługi Dickert DZS25

Dickert Otwieracz do bramy garażowej DZS25

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Dickert DZS25 (4 stron) w kategorii Otwieracz do bramy garażowej. Ta instrukcja była pomocna dla 7 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/4

EN Ceiling pull switch DZS25

28510670_DZS25_EN_2015-02-18.doc 1 / 4

Ceiling pull switch DZS25

Mounting and Operating Instructions

(Translation of original operating manual)

Always read before initial operation!

Ceiling pull switch DZS25

2 / 4 28510670_DZS25_EN_2015-02-18.doc

AA alkaline

12345678910

DIP

1 Intended use

Wireless remote control units are only approved for use with devices and systems where a

functional problem in the transmitter or receiver does not result in a hazard for people, animals or

property hazard or if this risk is covered by other safety equipment. The user must be informed that

the wireless remote control of door systems with a risk of accidents is only permissible, if at all,

with direct eye contact to the door system and when the motion range must be free of people,

animals and objects. Store the hand-held transmitter so that unwanted activation, e.g. by children

or animals, is impossible. The wireless remote control units in use work on generally-approved

frequencies (ISM bands). The operator of such wireless remote control units is not protected from

faults caused by other wireless systems or devices (e.g., wireless systems being operated in the

same frequency range such as baby phones, intercoms, etc.).

Any use other than the intended use shall be considered improper use for which the manufacturer

is not liable. The fitter, electrician or operating organisation bears the risk and the liability here.

2 Functional description

10 pin coding switch linear code

For setting the code with 18 bit linear operation.

"Unsymmetrical" coding must be set in transmitters which have a coding

switch!

Ceiling pull switch DZS25

28510670_DZS25_EN_2015-02-18.doc 3 / 4

2 pin DIP switch linear/Keeloq

DIP1 "OFF“ – Linear code

The coding switch provides the option to set 1024 different safety codes. At the

same time, you can also set several transmitters with the same code to control the

same receiver with all transmitters. If you leave all switches on "ON" or "OFF" at the

coding switch, then the sender works with one of 262,000 possible codes that are

sequentially programmed at the factory. In this case, the ceiling pull switch transmits a

coding that is equivalent to button 1 at the hand transmitter.

DIP1 "ON“ – Keeloq code

Function KeeLoq / change code

The transmitter works in accordance with the state of the art KeeLoq process. A new

code is calculated with each actuation. During normal use (garage door, etc.) it takes

more than 20 years before a code is repeated! Teach the transmitter in accordance

with the receiver instructions. The receiver checks the radio signal before the output

switches and it controls your unit. To do that, keep the transmit key pressed for at least

2 seconds. If the battery is charged, then the LED at the transmitter is illuminated

during this time.

DIP2 without function.

Radio transmission module with antenna

Transmission switch

Transmission duration as long as the switch is actuated, min. 3 data words, max 3 min.

Transmission LEDs

Illuminated during actuation, flashing alternatively during initialization.

Green - linear code is transmitted

Red - Keeloq code is transmitted

The respective LED flashes in transmission mode if the battery charge is weak.

The initialization is performed during the switch-over of the DIP1 coding switch , or

during battery change. The radio command is only provided during the next actuation

of the transmission switch.

Batteries

2 units AA Alkaline-Manganese required

Antenna:

Must be aligned at full length.

3 Range

Typical ranges are:

50 m in open space.

The range achieved at the usage location depends on the receiver and transmitter

positions as well as the antenna installation of the receiver.

Specyfikacje produktu

Marka:	Dickert
Kategoria:	Otwieracz do bramy garażowej
Model:	DZS25

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Dickert DZS25, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje Otwieracz do bramy garażowej Dickert

Dickert ACM 20 Instrukcja

18 Września 2024

Dickert AHS40 Instrukcja

12 Września 2024

Dickert DX40 Instrukcja

11 Września 2024

Dickert DX27 Instrukcja

9 Września 2024

Dickert DZS25 Instrukcja

5 Września 2024

Instrukcje Otwieracz do bramy garażowej

Najnowsze instrukcje dla Otwieracz do bramy garażowej

Chamberlain Liftmaster Instrukcja

14 Stycznia 2025

LiftMaster 1280-298LMC Instrukcja

12 Stycznia 2025

LiftMaster 8360 Premium Instrukcja

12 Stycznia 2025

LiftMaster 8500 Elite Instrukcja

11 Stycznia 2025

Somfy Freevia Essential Instrukcja

30 Grudnia 2025

Somfy Freevia 400 Instrukcja

9 Października 2024

Craftsman CMXZDCG4910 Instrukcja

30 Września 2024

Marantec Digital 302 Instrukcja

30 Września 2024

Marantec Comfort 270 Instrukcja

30 Września 2024

Somfy SGS Essential Instrukcja

29 Września 2024