Instrukcja obsługi Deltaco DUR-900

Deltaco czytnik kodów kreskowych DUR-900

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Deltaco DUR-900 (54 stron) w kategorii czytnik kodów kreskowych. Ta instrukcja była pomocna dla 4 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/54
A N O R D I C B R A N D
User Guide
Naudotojo vadovas
Lietotāja rokasgrāmata
Användarhandledning Kasutusjuhend
Käyttöohje Bedienungsanleitung
Brugervejledning Mode d’emploi
Brukerveiledning Instrukcja użytkowania
Gebruiksaanwijzing
ENG
SWE
FIN
DAN
NOR
LIT
LAV
EST
GER
FRA
POL
NLD
DUR-900
1
ENG - User Manual
Safety instructions
1. Do not look into or observe the device’s light, neither directly or through an optical instrument.
2. Do not disassemble or remove the lens cover. If the lens cover is removed, your eyes will be directly exposed to the light.
4. Keep the product away from children.
.
Do not continue to use the product if it has been damaged or deformed. Do not leave it in hot environments.
Product information
This barcode scanner provides an accurate, fast and easy complete solution for data entry and storage for computer
information systems.
The product has two working modes: manual and auto-sensor.
This product provides 4 interfaces to connect to any host computer system: Keyboard (Keyboard wedge), RS-232, USB
HID and VCOM.
the device has been powered off.
T r r r r rhis p oduct has mo e settings than available ba codes in this manual. If needed you can c eate you ow r r n ba codes to set you
ow “L ”n settings. One example is the ED on time , it has about 200 possible settings but only 4 examples of ba codes a e in thir r s
fo the co esponding setting you ant to c eate o changer rr w r r .
Scan barcodes
In order to obtain a good scan effect, you should aim the
barcode reader at the center of the barcode, but you can
aim from any direction.
The closer the scanner is to the barcode, the smaller the aiming beam is;
the farther away the scanner is from the barcode, the larger the aiming beam is.
If the barcode is small, the scanner should be close to the barcode; if the barcode is large, the scanner should be farther
away from the barcode, so the barcode can be read easily and correctly.
1. Scan window
2. Button
3. LED
4. Sound output
5. Cable removal hole
Cable removal
1. Locate the cable removal hole on the bottom of the scanner.
Readability VS performance
Each type of barcode has its own unique properties. Enable the ability to read barcode types via the settings found in this
manual. You can disable the scanner from r reading ba code types that ill not be used to impw rove the scanner’s performance.
Maintenance
1. Stains and dust on the scan window may affect the scanning. Use a lint-free cloth / lens tissue of good quality to gently
wipe clean the window if needed. Poor quality paper will damage the surface smoothness of the scan window and affect
the scanner’s effect.
2. The scanner’s housing can be wiped with a clean soft cloth. When needed, moisten the cloth with water or a mild soap
solution and wipe it with a soft cloth.
1
2
3
4
5
2
Troubleshooting
Q1. Problem: The data cable is correctly installed, but the indicator LED or beep sound is not working when the button is
pressed.
A1. Possible causes: No power or cable error. Solutions: Please make sure the cable is connected and the scanner is
turned on. When using the USB port, please connect the USB cable to the USB port of the computer motherboard. Do not
use an extended USB port or other USB extension cable. Check if the cable connection is loose.
Q2. Problem: The light is on but barcode cannot be read.
A2. Possible causes: The barcode type is not enabled, damaged barcode or inappropriate scan distance.
Solutions: Enable the barcode type. Try scanning other barcodes with the same barcode type.
Move the barcode scanner closer or farther away from the barcode.
Q3. Problem: T rhe scanned data is displayed inco ectly on the host afterr the
A3. Possible causes: Input error or other settings for the scanner. Solutions: Change input to default English input or
restore the scanner to factory default.
Q4. Problem: Other situations.
A4. Possible cause: Scanner operation error. Solutions: Turn off and reconnect the device and scanner correctly.
Turn on the power of the device, restore the scanner to the factory default and rescan the barcode.
Support
More product information can be found at www.deltaco.eu.
Contact us by e-mail: .help@deltaco.eu

Specyfikacje produktu

Marka: Deltaco
Kategoria: czytnik kodów kreskowych
Model: DUR-900

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Deltaco DUR-900, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje czytnik kodów kreskowych Deltaco

Deltaco

Deltaco DUR-900 Instrukcja

29 Sierpnia 2024
Deltaco

Deltaco POS-833 Instrukcja

22 Sierpnia 2024
Deltaco

Deltaco DUR-801 Instrukcja

17 Sierpnia 2024
Deltaco

Deltaco DUR-807 Instrukcja

13 Maja 2024

Instrukcje czytnik kodów kreskowych

Najnowsze instrukcje dla czytnik kodów kreskowych

Zebra

Zebra LS7808 Instrukcja

15 Stycznia 2025
Hamlet

Hamlet HBCS-2D360 Instrukcja

14 Stycznia 2025
Hamlet

Hamlet HBCS2D120U Instrukcja

14 Stycznia 2025
Hamlet

Hamlet HBCS-2DUWB Instrukcja

14 Stycznia 2025
Newland

Newland HR2180 Instrukcja

11 Stycznia 2025
Datalogic

Datalogic Magellan 8302 Instrukcja

11 Stycznia 2025
Honeywell

Honeywell Orbit HF680 Instrukcja

29 Grudnia 2024
IFM

IFM DTE900 Instrukcja

5 Grudnia 2024
Newland

Newland NFT10 Pilot Pro Instrukcja

10 Października 2024
Posiflex

Posiflex CD-3602U Instrukcja

9 Października 2024