Instrukcja obsługi DBX ZC-1

DBX Kontroler ZC-1

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla DBX ZC-1 (8 stron) w kategorii Kontroler. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/8
User Guide
ZC
Series
®
DriveRack
®
/ZonePRO
™
Z C S e r i e s Wa l l - M o u n t e d Z o n e C o n t r o l l e r s
ZC-1-4
ZC-6-9
ZC-Fire
ZC-BOB
®
DriveRack®/ZonePRO™User Manual
2
ZC-Remote Control Wall Controllers USER GUIDE
DECLARATION OF
CONFORMITY
Manufacturer’s Name: dbx Professional Products
Manufacturer’s Address: 8760 S. Sandy Parkway
Sandy, Utah 84070, USA
declares that the product:
Product name: dbx Zone Controllers Models: ZC1, 2, 3, 4, 6, 7,
8, 9, FIRE and BOB
Note: Product name may be suffixed by the letters -EU.
Product option: none
conforms to the following Product Specifications:
Safety: IEC 60065-98
EMC: EN 55013 (1990)
EN 55020 (1991)
Supplementary Information:
The product herewith complies with the requirements of the Low Voltage Directive 73/23/EEC and
the EMC Directive 89/336/EEC as amended by Directive 93/68/EEC.
Vice-President of Engineering
8760 S. Sandy Parkway
Sandy, Utah 84070, USA
Date: Februar y 3, 2003
Revised: September 10, 2004
European Contact: Your local dbx Sales and Service Office or
Harman Music Group
8760 South Sandy Parkway
Sandy, Utah
84070 USA
Ph: (801) 566-8800
Fax: (801) 568-7583
The symbol shown above is an internationally accepted
symbol that warn of potential hazards with electrical prod-
ucts. The exclamation point in an equilateral triangle indi-
cates that it is necessary for the user to refer to the
owner’s manual.
Zone Controller Wiring
The Zone Controllers, (ZC-1, ZC-2, ZC-3, ZC-4, ZC-6, ZC-7, ZC-8, ZC-9, and ZC-Fire) can
be wired serially or in parallel. To wire in series each Zone Controller must have an iden-
tification or zone number chosen using the DIP switches on the side of the controller (see
diagram A). Each controller must have a unique number chosen although there may be
multiple Zone Controllers controlling a single zone, or a single Zone Controller that con-
trols multiple outputs. The Zone Controllers can then be wired together and connected
to the DriveRack 220i, 260 or ZonePRO units (see diagram B).
The Zone Controllers may also be wired in parallel with the use of the ZC-BOB. To wire
in parallel (home run cabling), each controller must have a unique identification or num-
ber chosen using the DIP switches on the rear of the panel (see diagram A). To wire in
parallel, each controller must be wired into a port of the ZC-BOB with a connecting wire
going to the DriveRack or ZonePro (see diagram C). Diagram D shows the typical wiring
for ZC-4 Euroblock connections in which the installer needs to use SPDT (single-pole, dou-
ble-throw) switches with one side being connected to 5 volts (+VREF) and the other side
to ground (GND). Diagram E shows the proper way to interface the ZC-Fire to the fire
alarm system. Use only the relay/switch closure or the 5-24V DC inputs. Do not use both
inputs at the same time. For information regarding ZC setup, please see the respective
manual for the Driverack or ZonePro unit that you are setting up.
Diagram A
RJ45
CONNECT ONLY TO
ZONE CONTROLLER
IN P UT .
IEC60065UL-6500
80-1342-A
RJ45
CO N N E C T ON L Y T O
ZONE CONTROLLER
IN P UT .
IEC60065UL-6500
80-1342-A
ID# 1 ID# 4
Diagram B
ZC-Remote Control Wall Controllers USER GUIDE
®
DriveRack®/ZonePRO
™User Manual 3

Specyfikacje produktu

Marka: DBX
Kategoria: Kontroler
Model: ZC-1

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z DBX ZC-1, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Kontroler DBX

DBX

DBX ZC-1 Instrukcja

27 Sierpnia 2024

Instrukcje Kontroler

Najnowsze instrukcje dla Kontroler

COLBOR

COLBOR CTRL1 Instrukcja

16 Grudnia 2024
Speed-Link

Speed-Link Thunderstrike Instrukcja

11 Grudnia 2024
GVM

GVM YK22 Instrukcja

11 Grudnia 2024
IVT

IVT MPPTplus+ 20A Instrukcja

11 Grudnia 2024
IVT

IVT SCDplus Instrukcja

11 Grudnia 2024
Alfatron

Alfatron ALF-IPCON-HDMI Instrukcja

10 Grudnia 2024
Hotone

Hotone Ampero Control Instrukcja

7 Grudnia 2024
Hotone

Hotone Patch Kommander Instrukcja

7 Grudnia 2024
IFM

IFM AC1317 Instrukcja

5 Grudnia 2024
Thrustmaster

Thrustmaster Ferrari GT Experience Instrukcja

13 Października 2024