Instrukcja obsługi DBX DriveRack 220i

DBX nieskategoryzowany DriveRack 220i

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla DBX DriveRack 220i (41 stron) w kategorii nieskategoryzowany. Ta instrukcja była pomocna dla 9 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/41
User Manual
®
System Processor with Advanced Feedback Suppression
220i
The symbols shown above are internationally accepted symbols that warn of
potential hazards with electrical products. The lightning flash with arrowpoint in
an equilateral triangle means that there are dangerous voltages present within
the unit. The exclamation point in an equilateral triangle indicates that it is
necessary for the user to refer to the owner’s manual.
These symbols warn that there are no user serviceable parts inside the unit.
Do not open the unit. Do not attempt to service the unit yourself. Refer all
servicing to qualified personnel. Opening the chassis for any reason will void
the manufacturer’s warranty. Do not get the unit wet. If liquid is spilled on the
unit, shut it off immediately and take it to a dealer for service. Disconnect the
unit during storms to prevent damage.
WARNING FOR YOUR PROTECTION
READ THE FOLLOWING:
KEEP THESE INSTRUCTIONS
HEED ALL WARNINGS
FOLLOW ALL INSTRUCTIONS
the apparatus shall not be exposed to dripping or splashing liquid and no object filled
with liquid, such as vases, shall be placed on the apparatus.
CLEAN ONLY WITH A DRY CLOTH.
DO NOT BLOCK ANY OF THE VENTILATION OPENINGS. INSTALL IN ACCORDANCE WITH
THE MANUFACTURER’S INSTRUCTIONS.
DO NOT INSTALL NEAR ANY HEAT SOURCES SUCH AS RADIATORS, HEAT REGISTERS,
STOVES, OR OTHER APPARATUS (INCLUDING AMPLIFIERS) THAT PRODUCE HEAT.
ONLY USE ATTACHMENTS/ACCESSORIES SPECIFIED BY THE MANUFACTURER.
UNPLUG THIS APPARATUS DURING LIGHTNING STORMS OR WHEN UNUSED FOR LONG
PERIODS OF TIME.
Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized
plug has two blades with one wider than the other. A grounding type plug has two
blades and a third grounding prong. The wide blade or third prong are provided for your
safety. If the provided plug does not fit your outlet, consult an electrician for replace-
ment of the obsolete outlet.
Protect the power cord from being walked on or pinched particularly at plugs, conve-
nience receptacles, and the point where they exit from the apparatus.
Use only with the cart stand, tripod bracket, or table specified by the manufacture,
or sold with the apparatus. When a cart is used, use caution when moving the cart/
apparatus combination to avoid injury from tip-over.
Refer all servicing to to qualified service personnel. Servicing is required when the ap-
paratus has been damaged in any way, such as power-supply cord or plug is damaged,
liquid has been spilled or objects have fallen into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate normally, or has been dropped.
POWER ON/OFF SWITCH: The Power switch used in this piece of equipment DOES NOT
break the connection from the mains.
MAINS DISCONNECT: The plug shall remain readily operable. For rack-mount or instal-
lation where plug is not accessible, an all-pole mains switch with a contact separation
of at least 3 mm in each pole shall be incorporated into the electrical installation of the
rack or building.
If connected to 240V supply, a suitable CSA/UL certified power cord shall be used for
this supply.
This Equipment is intended for rack mount use only.
SAFETY INSTRUCTIONS
NOTICE FOR CUSTOMERS IF YOUR UNIT IS EQUIPPED WITH A POWER CORD.
WARNING: THIS APPLIANCE SHALL BE CONNECTED TO A MAINS SOCKET OUTLET WITH A PROTECTIVE
EARTHING CONNECTION.
THE CORES IN THE MAINS LEAD ARE COLOURED IN ACCORDANCE WITH THE FOLLOWING CODE:
GREEN aNd YELLOW - EaRth BLUE - NEUtRaL BROWN - LivE
AS COLOURS OF THE CORES IN THE MAINS LEAD OF THIS APPLIANCE MAY NOT CORRESPOND WITH
THE COLOURED MARKINGS IDENTIFYING THE TERMINALS IN YOUR PLUG, PROCEED AS FOLLOWS:
• THE CORE WHICH IS COLOURED GREEN AND YELLOW MUST BE CONNECTED TO THE TERMINAL
IN THE PLUG MARKED WITH THE LETTER E, OR WITH THE EARTH SYMBOL, OR COLOURED GREEN,
OR GREEN AND YELLOW.
• THE CORE WHICH IS COLOURED BLUE MUST BE CONNECTED TO THE TERMINAL MARKED N OR
COLOURED BLACK.
• THE CORE WHICH IS COLOURED BROWN MUST BE CONNECTED TO THE TERMINAL MARKED L OR
COLOURED RED.
THIS EQUIPMENT MAY REQUIRE THE USE OF A DIFFERENT LINE CORD, ATTACHMENT PLUG, OR BOTH,
DEPENDING ON THE AVAILABLE POWER SOURCE AT INSTALLATION. IF THE ATTACHMENT PLUG NEEDS
TO BE CHANGED, REFER SERVICING TO QUALIFIED SERVICE PERSONNEL WHO SHOULD REFER TO THE
TABLE BELOW. THE GREEN/YELLOW WIRE SHALL BE CONNECTED DIRECTLY TO THE UNITS CHASSIS.
CONDUCTOR WIRE COLOR
Normal Alt
L LIVE BROWN BLACK
N NEUTRAL BLUE WHITE
E EARTH GND GREEN/YEL GREEN
WaRNiNG: IF THE GROUND IS DEFEATED, CERTAIN FAULT CONDITIONS IN THE UNIT OR IN THE
SYSTEM TO WHICH IT IS CONNECTED CAN RESULT IN FULL LINE VOLTAGE BETWEEN CHASSIS AND
EARTH GROUND. SEVERE INJURY OR DEATH CAN THEN RESULT IF THE CHASSIS AND EARTH GROUND
ARE TOUCHED SIMULTANEOUSLY.
IMPORTANT SAFETY INSTRUCTIONS
ELECTROMAGNETIC COMPATIBILITY
This device complies with part 15 of the FCC Rules and the Prod-
uct Specifications noted on the . Declaration of Conformity
Operation is subject to the following two conditions:
• this device may not cause harmful interference, and
• this device must accept any interference received, including
interference that may cause undesired operation.
Operation of this unit within significant electromagnetic fields
should be avoided.
• use only shielded interconnecting cables.
DECLARATION OF CONFORMITY
Manufacturer’s Name: dbx Professional Products
Manufacturer’s Address: 8760 S. Sandy Parkway
Sandy, Utah 84070, USA
declares that the product:
Product name: dbx DriveRack 220i
Note: Product name may be suffixed by the EU.
Product option: None
conforms to the following Product Specifications:
Safety: IEC 60065 -01+Amd 1
EMC: EN 55022:2006
EN 55024:1998
FCC Part 15
Supplementary Information:
The product herewith complies with the requirements of the:
Low Voltage Directive 2006/95/EC
EMC Directive 2004/108/EC.
RoHS Directive 2002/95/EC
WEEE Directive 2002/96/EC
With regard to Directive 2005/32/EC and EC Regulation 1275/2008
of 17 December 2008, this product is designed, produced, and
classified as Professional Audio Equipment and thus is exempt from this
Directive.
Roger Johnsen
Director, Engineering
Signal Processing
8760 S. Sandy Parkway
Sandy, Utah 84070, USA
Date: May 31, 2012
European Contact: Your local dbx Sales and Service Office or
Harman Signal Processing
8760 South Sandy Parkway
Sandy, Utah
84070 USA
Ph: (801) 566-8800
Fax: (801) 568-7583
U.K. MAINS PLUG WARNING
A molded mains plug that has been cut off from the cord is
unsafe. Discard the mains plug at a suitable disposal facility.
NEVER UNDER ANY CIRCUMSTANCES SHOULD
YOU INSERT A DAMAGED OR CUT MAINS PLUG
INTO A 13 AMP POWER SOCKET.
Do not use the mains plug without the fuse cover in place.
Replacement fuse covers can be obtained from your local retailer.
Replacement fuses are 13 amps and MUST be ASTA approved to
BS1362.
If y want se is pro , do n it h ral u hold wa e. There a ou to dispo th duct ot mix wit gene ho se st is
sepa ate collectio ys se ec ic od ct acco ance egr n s tem for u d el tron pr u s in rd w h lit isl ti tha on at
r uir pr tr t, r overy a r g.eq es oper ea entm ec nd ecyclin
Private household in the 25 member states of the EU, in Switzerland and Norway may return their used
electronic products free of charge to designated collection facilities or to a retailer (if you purchase a similar
new one).
For Countries not mentioned above, please contact your local authorities for a correct method of disposal.
By doing so you will ensure that your disposed product undergoes the necessary treatment, recovery and
recycling and thus prevent potential negative effects on the environment and human health.
IMPORTANT SAFETY INSTRUCTIONS
220i
INTRO
CUSTOMER SERVICE INFO
Defining the
DriveRack
WARRANTY INFO
Introduction
2
220i
DriveRack® User Manual
Congratulations on your purchase of the dbx® 220i! The dbx 220i processor was designed to provide
Installers with programmable system processing along with dbx’s Advanced Feedback Suppression™
(AFS™) algorithm for superior system control and performance. While the 220i offers all the tools
necessary for processing a system, from EQ and De-Essing to Limiting and Ducking, the thing that
sets this product apart from the competition is the inclusion of our patent-pending AFS™ algorithm
that offers feedback filters with Qs up to 1/80th of an octave. This ensures that the music, or speech
that comes in, goes out unblemished by the feedback detection and elimination process. In hundreds of
demonstrations of this patent-pending algorithms, people have tried to discern between the original and
processed signal, but to no avail.
Beyond the processing that the 220i is capable of, the 220i also offers control from the ZC series wall
panel controllers. These controllers provide convenient remote control capability of Program change,
Zone output volume and Muting. The zone controllers are easy to install using CAT5 cable and fit in
standard wall boxes.
This manual will be your guide to understanding the full functionality of the powerful 220i. By
combining the different components, the configuration possibilities are limitless. After you have become
familiar with the unit, we encourage you to experiment and find the most effective and efficient way to
run your system by utilizing the powerful processing of the 220i.
0.1 - Defining the 220i System
The dbx 220i is the most effective way to manage all aspects of post mixer processing and signal routing.
The 220i essentially becomes the only device that you will need between the mixer and the power amps.
The following are just some of the features of the 220i.
220i features:
• Advanced Feedback Suppression (AFS™)
• Graphic and Parametric EQ
• Compressor
• Limiting
• Auto Gain Control (AGC)
• Noise Gate
• De-Esser
• Ducker
• Bandpass Filters
• 2x2 Matrix Mixer
• 1.3 Seconds of Delay
• RS-232 PC GUI control
• Mic/Line Inputs
• Wall Panel Control
• Security Lockout
Introduction
3
220i
DriveRack® User Manual
In addition to the amazing menu of processing available, the 220i also affords you the luxury of utilizing
dbx Zone-Controller series wall-mounted control panels that will allow you to remotely control various
parameters of the 220i. The ZC-1 offers remote programmable Volume control to any installation using
the DriveRack 220i. The ZC-2 provides programmable Volume and Mute control. Both the ZC-1 and
ZC-2 can be programmed to outputs of the DriveRack 220i. The ZC-3 allows Program Selection on
the 220i. The ZC-4 also offers Program Selection via Contact Closure inputs for Room Combining
applications. Up to six Zone Controllers can be used with a single DriveRack 220i, and can either be
wired in series or parallel. The ZC-BOB was created to accommodate “home-run” or parallel wiring to
the unit. With a maximum length of 1,000 ft., the Zone Controllers offer a simple way to create a simple
yet elegant solution to many installation applications.
123
456
ZC-BOB
VOL UME
0
1
2
3
456
7
8
9
10
ZC-1
VOL UME
0
1
2
3
456
7
8
9
10
MUT E
ZC-2
A
B
C
D
SEL ECT
AB
C
D
ZC-3
1+V 2 3 4 INOUT
ZC-4
0.2 - Service Contact Info
If you require technical support, contact dbx Customer Service. Be prepared to accurately describe the
problem. Know the serial number of your unit - this is printed on a sticker attached to the top panel. If
you have not already taken the time to fill out your warranty registration card and send it in, please do so
now.
Before you return a product to the factory for service, we recommend you refer to the manual. Make
sure you have correctly followed installation steps and operation procedures. If you are still unable to
solve a problem, contact our Customer Service Department at (801) 568-7660 for consultation. If you
need to return a product to the factory for service, you MUST contact Customer Service to obtain a
Return Authorization Number.
No returned products will be accepted at the factory without a Return Authorization Number.
Please refer to the Warranty information on the following page, which extends to the first end-user.
After expiration of the warranty, a reasonable charge will be made for parts, labor, and packing if you
choose to use the factory service facility. In all cases, you are responsible for transportation charges to
the factory. dbx will pay return shipping if the unit is still under warranty.
Use the original packing material if it is available. Mark the package with the name of the shipper and
with these words in red: DELICATE INSTRUMENT, FRAGILE! Insure the package properly. Ship
prepaid, not collect. Do not ship parcel post.
Introduction
4
220i
DriveRack® User Manual
0.3 - Warranty
1. The warranty registration card that accompanies this product must be mailed within 30 days after
purchase date to validate this warranty. You can also register online at www.dbxpro.com. Proof-
of-purchase is considered to be the responsibility of the consumer. A copy of the original purchase
receipt must be provided for any warranty service.
2. dbx warrants this product, when purchased new from an authorized U.S. dbx dealer and used solely
within the U.S., to be free from defects in materials and workmanship under normal use and service.
This warranty is valid to the original purchaser only and is non-transferable.
3. dbx liability under this warranty is limited to repairing or, at our discretion, replacing defective
materials that show evidence of defect, provided the product is returned to dbx WITH RETURN
AUTHORIZATION from the factory, where all parts and labor will be covered up to a period of two
years. A Return Authorization number must first be obtained from dbx. The company shall not be
liable for any consequential damage as a result of the product’s use in any circuit or assembly.
4. dbx reserves the right to make changes in design or make additions to or improvements upon this
product without incurring any obligation to install the same additions or improvements on products
previously manufactured.
5. The foregoing is in lieu of all other warranties, expressed or implied, and dbx neither assumes nor
authorizes any person to assume on its behalf any obligation or liability in connection with the sale of
this product. In no event shall dbx or its dealers be liable for special or consequential damages or from
any delay in the performance of this warranty due to causes beyond their control.
7
220i
DriveRack® User Manual
Section 1
1.2 - Front Panel
PC Connection
This DB-9 type connection is used to send and receive information to and from the computer running
the DriveWare™ software.
NOTE: Front and rear PC connections should not be used at the same time as these connections are
wired in parallel.
Load Button
The load button is used to load the selected program.
Program Display
This program display is used to indicate the currently selected program of the 220i.
Program Up and Down (Filter Clear Ch1 and Ch2)
These program up and down buttons are used to scroll through the program menu of the 220i. Pushing
and holding these buttons will clear the live filters on these channels if there are AFS modules in the
signal path.
PC LED
This LED (when lit), indicates that the 220i is connected to the PC. When it is flashing, the 220i is
sending/receiving information from the PC.
CLIP LED
This LED (when lit), .indicates that a signal is clipping, either in the analog input section, or in the DSP.
Input Meters
These meters monitor the signal level at the output of the A/D converter.
Threshold Meters
The threshold meters indicate that the threshold level has been crossed within the output dynamics
section. The tri-color LED will be green when the signal is below the threshold for a Compressor,
Limiter and AGC, and above the threshold for the Gate. Yellow indicates that the signal is in the over-
easy region in the Compressor or Limiter and within the Window of the AGC. Red indicates that the
signal has passed over the threshold for the Compressor, Limiter and AGC, or below the threshold for
the Gate.
Output Meters
These meters monitor the signal level at the input of the D/A converter.
Getting Started
8
220i
DriveRack® User Manual
1.3 - Connections
• When setting up the DriveRack 220i, make connections as follows:
• Always make connections prior to applying power to the unit.
• Connect the output from the sending device (mixer) to either of the two XLR input connectors
shown below.
• Make output connections from any one of the 2 output XLR or Euroblock connectors shown
below to the input of the selected power amps.
• It is recommended that the power amps are turned off prior to cycling power to the DriveRack
220i. Always make sure that your power amps are the last item turned on and the first turned
off.
Once all of the connections have been made and the unit is powered up, you can navigate through the
entire signal path of the DriveRack 220i from the included DriveWare GUI. The display provides you
with a clear and concise overview of each aspect of the signal path from the input to the output section.
1.4 - PC GUI Installation
Minimum System Requirements
• 266MHz processor
• Windows 98 edition 2 or Windows NT 4.0
• 16 bit color
• 64 meg RAM
Installation
• Install DriveWare from the included CD ROM or download DriveWare from the dbx website
at www.dbxpro.com.
• After clicking on the “.exe” install file, follow the instructions in the installer. The application
will proceed to prompt you for the installation location.
• Once the software installation is complete, it is recommended that you restart your computer.
Getting Started
Section 1
220i Section 2
SoFtWAre
oPerAtIon
Software Operation


Specyfikacje produktu

Marka: DBX
Kategoria: nieskategoryzowany
Model: DriveRack 220i

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z DBX DriveRack 220i, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje nieskategoryzowany DBX

DBX

DBX DriveRack PX Instrukcja

13 Sierpnia 2024
DBX

DBX goRack Instrukcja

13 Sierpnia 2024
DBX

DBX DI1 Instrukcja

26 Maja 2024
DBX

DBX 180 Instrukcja

21 Maja 2024
DBX

DBX 234 Instrukcja

17 Maja 2024
DBX

DBX 933 Instrukcja

16 Maja 2024
DBX

DBX ZC-8 Instrukcja

15 Maja 2024

Instrukcje nieskategoryzowany

Najnowsze instrukcje dla nieskategoryzowany

Asko

Asko DBI644MIB.S.TW/1 Instrukcja

28 Października 2024
Asko

Asko DFS233IB.S.TW/1 Instrukcja

28 Października 2024
Emko

Emko EZM-9920 Instrukcja

27 Października 2024
Emko

Emko ESM-3712-H Instrukcja

27 Października 2024
Emko

Emko ATS-10 Instrukcja

27 Października 2024
Emko

Emko EAOM-11.2 Instrukcja

27 Października 2024
Emko

Emko EPM-3790 Instrukcja

27 Października 2024
Emko

Emko EPM-7790 Instrukcja

27 Października 2024
Livarno Lux

Livarno Lux IAN 108340 Instrukcja

27 Października 2024
Livarno Lux

Livarno Lux HG06009A-BS Instrukcja

27 Października 2024