Instrukcja obsługi Danfoss PLUS+1

Danfoss Controller PLUS+1

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Danfoss PLUS+1 (74 stron) w kategorii Controller. Ta instrukcja była pomocna dla 5 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/74

User Manual

PLUS+1®

Service Tool

www.danfoss.com

Revision history Table of revisions

Date Changed Rev

October 2022 Supports 2022.3 1401

June 2022 Supports 2022.2 1301

March 2022 Supports 2022.1 1201

June 2021 Supports 2021.1 1101

February 2021 Supports 12.2 1003

May 2020 Supports 12.1 1002

Changed document number from 'AQ00000194' and 'L1307770' to 'AQ152986484649' 1001

November 2019 Supports 12.0 0901

April 2019 Supports 11.1 0801

November 2018 Supports 11.0 0701

May 2018 Supports 10.1 0601

October 2017 Supports 10.0 0501

March 2017 Supports 9.1 0401

October 2016 Supports 9.0 0301

August 2015 Supports 7.2.x and later 0200

October 2014 Supports 7.1.x and later BA

September 2014 Conversion to Danfoss layout AB

November 2013 First edition AA

User Manual

PLUS+1® Service Tool

2 | © Danfoss | October 2022 AQ152986484649en-001401

General information

Introduction........................................................................................................................................................................................5

About this manual...................................................................................................................................................................... 5

Intended use............................................................................................................................................................................5

Safety definitions and reading information...................................................................................................................... 5

Safety definitions................................................................................................................................................................... 5

Reading information.............................................................................................................................................................5

IEC 61508:2010 support tool certification references.........................................................................................................6

Important information to reduce risk....................................................................................................................................... 6

Fault checking and error handling.............................................................................................................................................7

Downloading and testing your applications .........................................................................................................................7

Learning about the PLUS+1® Service Tool...............................................................................................................................8

Getting ready.....................................................................................................................................................................................8

PLUS+1® hardware setup

CAN hardware installation............................................................................................................................................................ 9

CAN hardware installation troubleshooting...........................................................................................................................9

Using the PLUS+1® CG150-2 USB/CAN Gateway Interface Communicator..............................................................11

Using the PLUS+1® DP Series Display USB/CAN gateway............................................................................................... 11

Using the PLUS+1® InterLink gateway....................................................................................................................................12

Using the PLUS+1® Virtual CAN gateway.............................................................................................................................. 13

Using the PLUS+1® InterLink Remote gateway...................................................................................................................14

Using the third party Gateway devices via the RP1210 standard................................................................................ 15

Connection.......................................................................................................................................................................................15

Diagnosing gateway warnings and errors using the RP1210 standard..................................................................... 15

Using Reset Gateway in advanced settings..........................................................................................................................16

Virtual Mode.....................................................................................................................................................................................16

Managing protocols

Managing Protocols values........................................................................................................................................................ 18

Add new protocols........................................................................................................................................................................ 20

Protocol options.............................................................................................................................................................................21

PLUS+1 Service Tool window

Start page..........................................................................................................................................................................................23

System Navigator features..........................................................................................................................................................24

Locking and unlocking Diagnostic Navigator pane..........................................................................................................24

Restoring default layouts............................................................................................................................................................25

PLUS+1® Service Tool languages

Installing tool languages during setup..................................................................................................................................26

Selecting the PLUS+1® Service Tool language.................................................................................................................... 26

Selecting the Service Application language........................................................................................................................ 27

Downloading the application

Preparing to Download the Application File to the Controller.....................................................................................29

Downloading system download packages.......................................................................................................................... 32

Mandatory applications/missing ECUs.............................................................................................................................32

Retry downloads.......................................................................................................................................................................33

Parameter settings during the application download.....................................................................................................34

Recover ECU functions.................................................................................................................................................................36

Working with service application files

Introduction to service application files................................................................................................................................38

Log page......................................................................................................................................................................................38

Parameter page.........................................................................................................................................................................38

Manual Load of Service Application Files........................................................................................................................ 38

Scanning for service application files................................................................................................................................38

Boot loader mode..........................................................................................................................................................................39

Automatic scan for service application files.........................................................................................................................40

Opening hardware service files................................................................................................................................................ 41

Manual installation of diagnostic data files..........................................................................................................................41

User Manual