Instrukcja obsługi CyberData Systems Singlewire 011182

CyberData Systems głośnik Singlewire 011182

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla CyberData Systems Singlewire 011182 (2 stron) w kategorii głośnik. Ta instrukcja była pomocna dla 6 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/2
Quick Start Guide 930465A
1.0 Out-of-Box and Prior to Final Installation
1.1. Verify that you have received all of the parts listed on the Installation Quick Reference placemat.
1.2. Download the current manual, otherwise known as an Operation Guide, which is available on the
Documentation page at the following website address:
http://www.cyberdata.net/products/voip/digitalanalog/singlewirespeakerptt/docs.html
2.0 Select Power Source
3.0 Power Test
3.1. Plug in the CyberData device and monitor the LED activity on the front of the device. See the
following figure:
3.2. The GREEN power/status LED and the YELLOW network LED come on immediately. The
YELLOW network LED will blink to indicate network traffic. After about 27 seconds, the GREEN
power/status LED will blink twice to indicate that the board is fully booted.
This concludes the power test.
PoE Switch PoE Injector
Set PoE power type to IEEE 802.3af
Power Class 0 (15.4W)a
a. When initiating the device for the first time, we recommend manually adjusting the PoE switch port power
setting to Class 3 to ensure sufficient power allocation. Once the initial setup has been completed and the
device is SIP enabled, the Administrator may prefer a final power setting adjustment to Class 0.
CAT6 cable recommended—for longer distances
Be sure you are using a non-PoE switch or port
Make sure port is not in trunk mode
Set port to full duplex/ 100mbps
Spanning Tree Protocol (STP) must be disabled or Portfast enabled
Speaker
Status
(Green LED)
Network
Link/Activity
(Yellow LED)
The IP Endpoint Company
V2 Speaker, Push-to-Talk, Singlewire
Quick Start Guide
Quick Start Guide 930465A
4.0 InformaCast Configuration File Retrieval
4.1. DHCP should be enabled. After the speaker initializes, it will send a broadcast to the DHCP server
to ask for the location of its InformaCastSpeaker.cfg configuration file.
4.2. SLP or TFTP?
•SLP should be enabled on InformaCast version 5.0.4 or higher. SLP is an InformaCast protocol
introduced in InformaCast version 5.0.4. The speaker will retrieve its configuration file from an
InformaCast server folder specified by SLP. SLP method is preferred.
•TFTP servers may be used instead of SLP. In this alternate scenario, DHCP option 150 is required to
provide the speaker with the address of the TFTP server. Otherwise, the speaker will be unable to
retrieve its configuration file.
Note The CyberData V2 Ceiling Speaker and InformaCast server should be on the same subnet
during the speaker's initial configuration if it cannot access the VLANs upon which the
InformaCast Server and DHCP servers are located.
5.0 Singlewire-Enabled V2 Ceiling Speaker Identification and Testing
5.1. Ensure the InformaCast Server has detected a new speaker.
5.2. Test the newly detected speaker.
5.3. Add the newly detected speaker to the InformaCast Server.
6.0 Contacting CyberData VoIP Technical Support
For quality assurance purposes, we ask that you please visit our website and complete our Support form
which is available at the following website address:
http://w ww.cybe rdata.net/support/contac tsupportvoip .html
The Support form initiates a ticket which CyberData uses for tracking customer requests. Most
importantly, the Support form provides us with pertinent troubleshooting information. Please include as
much detail as possible in the Comments section of the Support form.
Be prepared to provide a Wireshark capture of the speaker's boot process and ensure you have properly
mirrored the speaker's switch port.
Requests for Returned Materials Authorization (RMA) numbers require an active VoIP Technical Support
ticket number.
If you have purchased a Singlewire-Enabled V2 Ceiling Speaker in error, please immediately contact your
authorized distributor or reseller for exchange. CyberData Corporation offers repair services under the
Manufacturer's Limited 2 Year Warranty but is unable to offer exchanges.

Specyfikacje produktu

Marka: CyberData Systems
Kategoria: głośnik
Model: Singlewire 011182

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z CyberData Systems Singlewire 011182, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje głośnik CyberData Systems

CyberData Systems

CyberData Systems SIP 011393 Instrukcja

2 Października 2024
CyberData Systems

CyberData Systems Singlewire 011182 Instrukcja

2 Października 2024
CyberData Systems

CyberData Systems SIP-enabled IP V2 Instrukcja

2 Października 2024
CyberData Systems

CyberData Systems SIP IP66 Instrukcja

2 Października 2024
CyberData Systems

CyberData Systems 11394 Instrukcja

28 Września 2024
CyberData Systems

CyberData Systems 011520 Instrukcja

28 Września 2024
CyberData Systems

CyberData Systems 011180 Instrukcja

28 Września 2024
CyberData Systems

CyberData Systems 011487 Instrukcja

28 Września 2024
CyberData Systems

CyberData Systems InformaCast Instrukcja

28 Września 2024
CyberData Systems

CyberData Systems 011181 Instrukcja

28 Września 2024

Instrukcje głośnik

Najnowsze instrukcje dla głośnik

Teufel

Teufel Rockster Air Instrukcja

15 Października 2024
Alpine

Alpine PSS-22WRA Instrukcja

15 Października 2024
Bauhn

Bauhn APPS-0724 Instrukcja

15 Października 2024
Aiwa

Aiwa SP-A100 Instrukcja

15 Października 2024
Harman Kardon

Harman Kardon Citation One Instrukcja

14 Października 2024
Alpine

Alpine 30MC Instrukcja

14 Października 2024
Magnat

Magnat Needle 9000 ALU Instrukcja

14 Października 2024
Pioneer

Pioneer SP-T22A-LR Instrukcja

14 Października 2024
Sharp

Sharp PS-932 Instrukcja

14 Października 2024
Pyle

Pyle PDWR64BTW Instrukcja

13 Października 2024