Instrukcja obsługi CyberData Systems 011523


Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla CyberData Systems 011523 (2 stron) w kategorii głośnik. Ta instrukcja była pomocna dla 4 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/2
Quick Reference 931750A © 2020, CyberData Corporation, ALL RIGHTS RESERVED.
Parts
FIts 24-inches x 24-inches and 24-inches x 48-inches ceiling tile
(1) Auxiliary Analog 2 x 2 Ceiling Tile Drop-In Speaker Assembly
Dimensions
23.8 [605]
23.8 [605]
Dimensions are in Inches [Millimeter]
3.6 [92]
Approximately
Contacting CyberData
Sales: (831) 373-2601 ext. 334
Support: 831-373-2601 ext. 333
Support Website: http://support.cyberdata.net/
RMA Department: (831) 373-2601 ext. 136
RMA Email: RMA@CyberData.net
RMA Status: http://support.cyberdata.net/
Warranty Information: http://support.cyberdata.net/
Corporate Headquarters
CyberData Corporation
3 Justin Court
Monterey, CA 93940, USA
Phone: 831-373-2601
Fax: 831-373-4193
http://www.cyberdata.net/
The IP Endpoint Company
Installation Quick Reference
Auxiliary Analog 2 x 2 Ceiling Tile Drop-In Speaker
011523
© 2020, CyberData Corporation, ALL RIGHTS RESERVED. 931750A Quick Reference
Installation Procedure
To install the Auxiliary Analog 2 x 2 Ceiling Tile Drop-In Speaker, complete the following steps while referencing the
figure below:
1. Remove the Ceiling Tile (the figure below shows a 2 x 2 Grid) from the Ceiling Grid. Cut the 2 x 4 Ceiling Tile in
Half if using a 2 x 4 Grid.
2. Place the Cross T* in the Middle for Support (Only on a 2 x 4 Grid).
3. Use a Flat Blade Screwdriver to Pry the Seismic Tether Bracket(s) on the 2 x 2 Auxiliary Ceiling Tile Speaker
Assembly.
4. Install Eyebolt(s) or Nail(s) to the Joist.
5. Connect the Speaker Wire(s) to the Blinding Posts on the 2 x 2 Auxiliary Ceiling Tile Speaker Assembly.
6. Use Steel Wire(s) to Connect Seismic Tether Bracket(s) to the Eyebolt(s) or Nail(s). Place the 2 x 2 Auxiliary
Ceiling Tile Speaker Assembly on to the Ceiling Grid and the Cross T* (see Step 2).
Installing the Auxiliary Analog 2 x 2 Ceiling Tile Drop-In Speaker
Use a Flat Blade Screwdriver
to Pry Up the Seismic Tether Bracket
Joist
Eyebolt / Nail
*
*
*
*
Speaker Assembly
2 x 2 Auxiliary Ceiling Tile
Steel Wire
*
Remove
Ceiling Tile
1
Drop-in the 2 x 2 Ceiling Tile Speaker Assembly
6
3
4
5
Cross T
Install Cross T (Not Included)
Only on a 2 x 4 Grid
2


Specyfikacje produktu

Marka: CyberData Systems
Kategoria: głośnik
Model: 011523

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z CyberData Systems 011523, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje głośnik CyberData Systems

Instrukcje głośnik

Najnowsze instrukcje dla głośnik