Instrukcja obsługi CRUX VIMCF-93C


Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla CRUX VIMCF-93C (2 stron) w kategorii Nie skategoryzowane. Ta instrukcja była pomocna dla 4 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/2
8-PIN
(male plug)
4 5 6
ON
1 2 3
TO FACTORY
HARNESS
VOLUME T UNE
52-PIN
(male plug)
TO FACTORY
DISPLAY
52-PIN
(female plug)
4 5 6
TO ENABLE VIDEO
IN-MOTION 1. On = Enable VIM
2. Not Used
3. Not Used
4. Not Used
5. Not Used
6. Not Used
ON
1 2 3
SAFETY WARNING:
THIS INTERFACE IS DESIGNED TO ACTIVATE
VIDEO IN-MOTION TO ALLOW THE PASSENER
ACCESS TO THE ADDRESS INPUT WHILE THE
VEHICLE IS IN-MOTION. THIS INTERFACE MAY
CAUSE AN ERROR WHEN SERVICED AT THE OEM
DEALER. BE AWARE THAT MOST DEALERS
WILL ATTEMPT TO VOID THE MANUFACTURERS
WARANTY WHEN INSTALLING ANY AFTERMARKET
EQUIPMENT. IMPROPER USE OF THIS INTERFACE
BY THE DRIVER MAY RESULT IN CITATION. DRIVER
MUST KEEP FULL ATTENTION ON THE ROAD AND
RESPOSIBILITY ON THE SAFETY OF HIS
PASSENGERS.
INTERFACI N G SOLUTIONS
VIDEO IN-MOTION FOR DODGE, JEEP & RAM VEHICLES 2013-UP
DODGE
2014 - 2015 Durango
RAM
2013 - 2015 1500
2013 - 2015 2500
2013 - 2015 3500
JEEP
2014 - 2015 Grand Cherokee
IMPORTANT:
Compatible Nav Radio Type:
U-CONNECT 8.4” SCREEN (1-Piece)
VIMCF-93C We recommend reading this installation guide rst before starting any
work. Following these instructions from “Start” to” Finish” will ensure
a smooth and hassle free installation. We oer telephone support M-F
9:00 AM – 5:00PM PDT at 1 (855) 822-1348. We are here to help.
PARTS INCLUDED:
(1) CF-93C Interface
(1) CF-93C T-Harness
(1) Instruction
PRECAUTIONS:
- Remove the negative side of the battery to avoid any short circuits
durring the installation.
- Do not install the interface near any major components or near the
HVAC system. This may cause damage or overheating to the vehicle.
- Do not disconnect the airbag connection behind the radio panel.
PRELIMINARY:
Please read the entire mannual before installing this interface.
INSTALLATION OVERVIEW
TROUBLE SHOOTING
1. No video display while driving.
- Make sure the dip swithces are in the proper location.
Rev. 012015
INSTALLING THE INTERFACE:
1. Remove the factory display to gain access to the factory connectors.
2. Remove the 52-Pin connector from behind the display.
2. Make the T-Harness connections behind the factory display.
(if the connectors do not match please contact tech support)
4. Set dip switch “1” to permanently activate the VIM feature.
5. Test the Navigation address input while the car is in-motion to verify
the VIM is active.
SETTING THE DIP SWITCHES
4 5 6
TO ENABLE VIDEO
IN-MOTION 1. On = Enable VIM
2. Not Used
3. Not Used
4. Not Used
5. Not Used
6. Not Used
ON
1 2 3
8.4”
DISPLAYS
INTERFACI N G SOLUTI O N S
VIDEO IN-MOTION FOR DODGE, JEEP & RAM VEHICLES 2013-UP
DODGE
2014 - 2015 Durango
RAM
2013 - 2015 1500
2013 - 2015 2500
2013 - 2015 3500
JEEP
2014 - 2015 Grand Cherokee
IMPORTANT:
Compatible Nav Radio Type:
U-CONNECT 8.4” SCREEN (1-Piece)
VIMCF-93C
Rev. 012015
COMPATIBLE RADIOS:
8.4” SCREEN
(SEPARATE KNOBS)
One Piece Radio
5” SCREEN
6-BUTTON
(SEPARATE
KNOBS)
4.3” SCREEN
6-BUTTON
(2 KNOBS)
4.3” SCREEN
4-BUTTON
(2 KNOBS)


Specyfikacje produktu

Marka: CRUX
Kategoria: Nie skategoryzowane
Model: VIMCF-93C

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z CRUX VIMCF-93C, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje Nie skategoryzowane CRUX

Instrukcje Nie skategoryzowane

Najnowsze instrukcje dla Nie skategoryzowane