Instrukcja obsล‚ugi CRUX SWRSU-38B

CRUX nieskategoryzowany SWRSU-38B

Przeczytaj poniลผej ๐Ÿ“– instrukcjฤ™ obsล‚ugi w jฤ™zyku polskim dla CRUX SWRSU-38B (3 stron) w kategorii nieskategoryzowany. Ta instrukcja byล‚a pomocna dla 29 osรณb i zostaล‚a oceniona przez 2 uลผytkownikรณw na ล›rednio 4.5 gwiazdek

Pobierz PDF
Strona 1/3
Crux Interfacing Solutions โ€ข 21541 Nordhoff St., Unit C, Chatsworth, CA 91311
phone: (818) 609-9299 โ€ข fax: (818) 996-8188 โ€ข www.cruxinterfacing.com
rev.022120
SWRSU-38B
Radio Replacement with Steering Wheel Control Retention for
Select SUBARU Vehicles 2008 - 2015
1 of 3
RADI O REPL ACEME NT
SWC RET ENTIO N
+
R
INTERFACING SOLUTIONS
- Retains factory features in select Subaru vehicles while func๎žŸoning with an a๎Œermarket radio.
- Pre-programmed to retain factory Steering Wheel Controls.
PRODUCT FEATURES:
PARTS INCLUDED:
SWRSU-38B Module SU-38B Harness SWC Cable
INSTALLATION DIAGRAM:
AFTERMARKET
RADIO
4-Pin
Connector
Cap or insulate if
not being used
Kenwood/JVC (BLUE / YELLOW )
Insulate with tape
if not being used
3.5MM SWC CABLE
Plug in the 3.5MM SWC cable to the 4-pin port
on the module. See โ€œDIP SWITCH SETTINGSโ€ section.
ON RADIO VEHICLE
1 2 3 4 5 6 7 8
+12V Constant Yellow
+12V ACC Red
Ground Black
๎˜ฏ๎ฏ๎ฏ๎žต๎ต๎๎ถ๎œ‚๎žŸ๎ฝ๎ถ๎˜ƒ๎ฅพ๎จฝ๎ฅฟ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎™‹๎žŒ๎œ‚๎ถ๎๎œž
Antenna Power Blue
๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜˜๎๎ต๎ต๎œž๎žŒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎™‹๎žŒ๎œ‚๎ถ๎๎œž๎ฅฌ๎™ด๎š๎๎žš๎œž
๎™š๎๎๎š๎žš๎˜ƒ๎˜ฆ๎žŒ๎ฝ๎ถ๎žš๎˜ƒ๎ฅพ๎จฝ๎ฅฟ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ง๎žŒ๎œ‚๎Ÿ‡
๎™š๎๎๎š๎žš๎˜ƒ๎˜ฆ๎žŒ๎ฝ๎ถ๎žš๎˜ƒ๎ฅพ๎ฅฒ๎ฅฟ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ง๎žŒ๎œ‚๎Ÿ‡๎ฅฌ๎˜‘๎ฏ๎œ‚๎œ๎ฌ
๎˜พ๎œž๎Œ๎˜ƒ๎˜ฆ๎žŒ๎ฝ๎ถ๎žš๎˜ƒ๎ฅพ๎จฝ๎ฅฟ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎™ด๎š๎๎žš๎œž
๎˜พ๎œž๎Œ๎˜ƒ๎˜ฆ๎žŒ๎ฝ๎ถ๎žš๎˜ƒ๎ฅพ๎ฅฒ๎ฅฟ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎™ด๎š๎๎žš๎œž๎ฅฌ๎˜‘๎ฏ๎œ‚๎œ๎ฌ
๎™š๎๎๎š๎žš๎˜ƒ๎™š๎œž๎œ‚๎žŒ๎˜ƒ๎ฅพ๎จฝ๎ฅฟ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎™ณ๎๎ฝ๎ฏ๎œž๎žš
๎™š๎๎๎š๎žš๎˜ƒ๎™š๎œž๎œ‚๎žŒ๎˜ƒ๎ฅพ๎ฅฒ๎ฅฟ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎™ณ๎๎ฝ๎ฏ๎œž๎žš๎ฅฌ๎˜‘๎ฏ๎œ‚๎œ๎ฌ
๎˜พ๎œž๎Œ๎˜ƒ๎™š๎œž๎œ‚๎žŒ๎˜ƒ๎ฅพ๎จฝ๎ฅฟ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ง๎žŒ๎œž๎œž๎ถ
๎˜พ๎œž๎Œ๎˜ƒ๎™š๎œž๎œ‚๎žŒ๎˜ƒ๎ฅพ๎ฅฒ๎ฅฟ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ง๎žŒ๎œž๎œž๎ถ๎ฅฌ๎˜‘๎ฏ๎œ‚๎œ๎ฌ
TO FACTORY
HARNESS
12-Pin Black
Connector
Ground
AFTERMARKET
RADIO SELECTOR
(See Page 2)
SUBARU
SWC SETTING
(See Page 2)
ON RADIO VEHICLE
1 2 3 4 5 6 7 8
To aftermarket
radio SWC wire or
3.5mm port
GREEN
BROWN BROWN
Connect BROWN to BROWN wire.
***See special note on 2010 & 2011 Forester, Legacy and Outback connection on page 2***
Crux Interfacing Solutions โ€ข 21541 Nordhoff St., Unit C, Chatsworth, CA 91311
phone: (818) 609-9299 โ€ข fax: (818) 996-8188 โ€ข www.cruxinterfacing.com
rev.022120
SWRSU-38B
Radio Replacement with Steering Wheel Control Retention for
Select SUBARU Vehicles 2008 - 2015
2 of 3
RADI O REPL ACEME NT
SWC RET ENTIO N
+
R
INTERFACING SOLUTIONS
DIP SWITCH SETTINGS:
SUBARU STEERING WHEEL CONTROL DIP SWITCH SETTING:
NOTE: Insulate the Blue/Yellow wire or 3.5mm plug if not being used.
AFTERMARKET RADIO DIP SWITCH SETTINGS:
RADIO BRAND: DIP: 1 2 3 4
Atoto, Dual, Farenheit, Jensen, Pioneer
Power Acoustik, Soundstream
Blaupunkt, Most o๎˜Ÿ-brand Radios
Alpine
Clarion
Kenwood
JVC
Boss, Old Sony
New Sony
OFF OFF ON ON
OFF OFF ON ON
OFF OFF ON ON
OFF OFF OFF OFF
OFF ON ON OFF
OFF ON ON ON
OFF ON OFF ON
OFF ON OFF OFF
OFF OFF ON OFF
SWC MODULE
ON RADIO VEHICLE
1 2 3 4 5 6 7 8
NOTE: For Atoto, Blaupunkt, Dual, Farenheit, Power Acoustik, Soundstream, and most o๎˜Ÿ-brand radios,
check the aftermarket radioโ€™s manual to see if the SWC buttons need to be programmed.
3.5MM SWC CABLE
Plug in the 3.5MM to 4-Pin SWC cable to the SWC module.
DIP: 5 6 7 8
Panasonic made Radio
Clarion made Radio*
Clarion made Radio**
Fujitsu Ten made Radio
ON OFF OFF ON
OFF ON OFF ON
ON OFF ON OFF
OFF ON OFF ON
SWC MODULE
ON RADIO VEHICLE
1 2 3 4 5 6 7 8
Original radio manufacturer informa๎žŸon can be found on the label on top of the radio.
STEERING WHEEL CONTROL DIP SWITCHES ARE TO BE SET IN ACCORDANCE WITH THE ORIGINALLY REMOVED FACTORY RADIO:
*For steering wheels with pickup and hangup phone bu๎žฉons.
**For steering wheels without pickup and hang up phone bu๎žฉons.
For the year model Subaru vehicles listed above, check the factory radio harness if it has a GREEN/YELLOW wire across the
BROWN wire on the SWRSU-38B harness (see diagram A). If it has a GREEN/YELLOW wire follow the connec๎žŸon chart below
and refer to diagram B. Set DIP switches 5 to 8 to: . ON OFF ON OFF
SPECIAL NOTE ON 2010 & 2011 FORESTER, LEGACY and OUTBACK:
BROWN
BLACK
BLACK
SWRSU-38B Harness
GREEN/YELLOW
ORANGE/WHITE
Factory Harness
BLACK
diagram A
WITHOUT Phone bu๎žฉons on steering wheel disconnect BROWN wire
WITH Phone bu๎žฉons on steering wheel disconnect BROWN wire and connect to GREEN wire
GREEN
BROWN
BROWN
diagram B
SU-38B Harness
Crux Interfacing Solutions โ€ข 21541 Nordhoff St., Unit C, Chatsworth, CA 91311
phone: (818) 609-9299 โ€ข fax: (818) 996-8188 โ€ข www.cruxinterfacing.com
rev.022120
SWRSU-38B
Radio Replacement with Steering Wheel Control Retention for
Select SUBARU Vehicles 2008 - 2015
3 of 3
RADI O REPL ACEME NT
SWC RET ENTIO N
+
R
INTERFACING SOLUTIONS
VEHICLE APPLICATIONS:
SUBARU
2009-2015
2008-2014
2010-2014
2010-2014
2013-2014
Forester*
Impreza (WRX)
Legacy
Outback*
XV Crosstrek
Subaru Outback Radio
INSTALLATION INSTRUCTIONS:
1. We recommend pu๎žซng tape
around the radio bezel to protect the
dashboard from being scratched.
2. Use a plas๎žŸc pry bar and carefully li๎Œ
the radio bezel going all the way around
it. Having a second pry bar would help.
3. Once you have li๎Œed the radio bezel,
carefully pull it out. Again, slowly going
all the way around it using your hands.
4. There are 4 screws holding the radio. 5. Pull out the radios and unplug the
connectors.
6. Plug in the SWRSU-38B T-harness
to the vehicle harness and hide the
module in the radio cavity.
7. Use the necessary dash kit (not included) to complete the installa๎žŸon. Connect the a๎Œermarket radio wires to the
SWRSU-38B T-harness.
8. Test the radio for func๎žŸonality before installing the new radio into the dash. Carefully reinstall the radio bezel.
*See special note on 2010 and 2011 Forester and Outback on page 2.

Specyfikacje produktu

Marka: CRUX
Kategoria: nieskategoryzowany
Model: SWRSU-38B

Potrzebujesz pomocy?

Jeล›li potrzebujesz pomocy z CRUX SWRSU-38B, zadaj pytanie poniลผej, a inni uลผytkownicy Ci odpowiedzฤ…


Instrukcje nieskategoryzowany CRUX

CRUX

CRUX SWRFD-60E Instrukcja

26 Maja 2024
CRUX

CRUX SWRSU-38B Instrukcja

14 Maja 2024
CRUX

CRUX SWRTY-61P Instrukcja

11 Maja 2024
CRUX

CRUX ACP-WLX Instrukcja

8 Maja 2024

Instrukcje nieskategoryzowany

Najnowsze instrukcje dla nieskategoryzowany

Meec Tools

Meec Tools 010-084 Instrukcja

6 Paลบdziernika 2024
Outwell

Outwell Scenic Road 250 Instrukcja

5 Paลบdziernika 2024
Impact

Impact Qualite QL-3560-LED Instrukcja

4 Paลบdziernika 2024
Impact

Impact QuikBalance Instrukcja

4 Paลบdziernika 2024
Impact

Impact CA-112 Instrukcja

4 Paลบdziernika 2024
Impact

Impact Forever Ready Cool FRC-24-LED Instrukcja

4 Paลบdziernika 2024
Impact

Impact LS-BHA Instrukcja

4 Paลบdziernika 2024
Impact

Impact LKB-5C Instrukcja

4 Paลบdziernika 2024
Impact

Impact Varipole Drop Ceiling Adapter Instrukcja

4 Paลบdziernika 2024
Impact

Impact RST-001 Instrukcja

4 Paลบdziernika 2024