Instrukcja obsługi Crunch CREQ7B


Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Crunch CREQ7B (10 stron) w kategorii nieskategoryzowany. Ta instrukcja była pomocna dla 10 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/10
Operator’s Guide
CREQ7B
Thank you for purchasing the CRUNCH CREQ7B, 7-Band Equalizer/
two-way crossover. This unit has both a pre-amp equalizer and
crossover to provide the multi-speaker system of your vehicle with
improved sound performance. Please read the entire manual to
ensure proper connections and application.
CAUTION
Always consider consulting a professional audio installer
before installing any audio components. Be careful and take
your time. Do not let wires make contact with metal edges or
hot engine components.
Features
ILLUMINATED RED CONTROL KNOB LEDS
LOW AND HIGH LEVEL AUDIO INPUTS (SPEAKER LEVEL)
DESIGNATED SUBWOOFER UNBALANCED OUTPUT
SUBWOOFER X-OVER FREQUENCY CONTROL
INPUT LEVEL CONTROL ADJUSTMENT
FADER CONTROL
HALF DIN CHASSIS SIZE
MOUNTING HARDWARE (INCLUDED)
SEVEN EQUALIZATION BANDS EACH ADJUST +/- 12dB
1
Mounting and Hardware
Prior to mounting, connect the wires
to ensure proper operation.
MOUNTING
1. Select the desired mounting location, either under the dash or
in the dash. Make sure that there is adequate depth for the CREQ7B.
2. Use the mounting brackets and hardware provided. Make sure
there is proper clearance for the mounting bracket screws when
attaching under the dash. Use caution to ensure there are no wiring
harnesses behind the dash panel (where the mounting
screws are fastened).
3. Route the power, ground, and remote wires away from moving
parts to prevent pinching or shortened wires.
WIRING
1. : The power wire should connect to a constant or Power Wire
switched +12 volt source with a in-line fuse. We recommend (2 Amp)
that you use the radio constant or switch +12 volt source.
2. : Connect the ground wire to a clean chassis ground Gound Wire
point. Be sure to remove all paint and primer to expose clean metal.
Use a ring terminal and lock or star washer to secure the ground wire.
3. : The remote wire should be connected to the source Remote Wire
until remote or antenna wire that provides +12 volts when the
source unit is “on” and 0 volts when the source unit is turned “off.”
2


Specyfikacje produktu

Marka: Crunch
Kategoria: nieskategoryzowany
Model: CREQ7B

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Crunch CREQ7B, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje nieskategoryzowany Crunch

Crunch

Crunch GTi300T Instrukcja

9 Września 2024
Crunch

Crunch GTi250S Instrukcja

9 Września 2024
Crunch

Crunch GTi200S Instrukcja

9 Września 2024
Crunch

Crunch CRXR Instrukcja

9 Września 2024
Crunch

Crunch CREQ7B Instrukcja

9 Września 2024
Crunch

Crunch GP690 Instrukcja

9 Września 2024

Instrukcje nieskategoryzowany

Najnowsze instrukcje dla nieskategoryzowany

Asko

Asko DBI644MIB.S.TW/1 Instrukcja

28 Października 2024
Asko

Asko DFS233IB.S.TW/1 Instrukcja

28 Października 2024
Emko

Emko EZM-9920 Instrukcja

27 Października 2024
Emko

Emko ESM-3712-H Instrukcja

27 Października 2024
Emko

Emko ATS-10 Instrukcja

27 Października 2024
Emko

Emko EAOM-11.2 Instrukcja

27 Października 2024
Emko

Emko EPM-3790 Instrukcja

27 Października 2024
Emko

Emko EPM-7790 Instrukcja

27 Października 2024
Livarno Lux

Livarno Lux IAN 108340 Instrukcja

27 Października 2024
Livarno Lux

Livarno Lux HG06009A-BS Instrukcja

27 Października 2024