Instrukcja obsługi Conair GS61R

Conair odkurzacz parowy GS61R

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Conair GS61R (2 stron) w kategorii odkurzacz parowy. Ta instrukcja była pomocna dla 4 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/2

IMPORTANT SAFETY

INSTRUCTIONS

When using electrical appliances, especially

when children are present, basic safety pre-

cautions should always be taken, including

the following:

READ ALL INSTRUCTIONS

BEFORE USING

DANGER — Any appliance is elec-

trically live even when the switch is off.

To reduce the risk of death by electric shock:

1. Always unplug immediately after using.

2. Do not place or store appliance where it

can fall or be pulled into a tub or sink.

3. Do not place in, or drop into, water or other

liquids.

4. If an appliance falls into water, unplug it

immediately. Do not reach into the water.

WARNING —

To reduce the risk of

burns,

electrocution, fire, or injury to persons:

1. Do not overfill steamer as it can cause hot

water to boil out.

2. This appliance should not be used near

children or by the physically challenged.

Unsupervised use could result in fire or

personal injury. This appliance is not recom-

mended for use by children.

3. Use this appliance only for its intended use

as described in this manual. Do not use attach-

ments not recommended by the manufacturer.

4. Never operate this appliance if it has a

damaged cord or plug, if it is not work-

ing properly, or if it has been dropped or

damaged, or dropped into water. Do not

attempt to repair the appliance. Incorrect

reassembly or repair could cause a risk

of fire, electric shock, or injury to persons

when the appliance is used. Return the

appliance to an authorized service center

for examination

and repair.

5. Keep the cord away from heated surfaces.

Do not pull or twist cord. Let appliance cool

completely before putting away. Loop cord

loosely around appliance when storing.

6. Do not use outdoors or operate where

aerosol (spray) products are being used or

where oxygen is being administered.

7. To reduce likelihood of circuit overload, do

not operate another high-wattage appliance

on the same circuit.

8. Do not use extension cord to operate

appliance. While it is not recommended, if

an extension cord is absolutely necessary, a

15 ampere rated cord should be used. Cords

rated for less amperage may overheat. Care

should be taken to arrange the cord so that

the cord cannot be pulled or tripped over.

9. Use caution when changing attachments

as they may contain hot water from

condensation. T-nozzle should never be

placed on the unit when in use or when pre-

heating. Ensure the attachments are dry or

cooled off to avoid contact with hot water.

10. Do not hold steamer during use. Steamer

must sit on floor while steaming.

11. Allow unit to cool before emptying reservoir

for storage.

12. Use caution when removing hose cap.

Remove slowly.

13. Do not use if unit has been dropped or

damaged.

14. Always disconnect appliance from

electrical outlet when filling with water

or emptying and when not in use.

15. Do not switch on the unit before the hose

cap has been secured with the unit.

CAUTION —

1. This appliance should never be left

unattended when plugged in.

2. This appliance has a polarized plug (one

blade is wider than the other). As a safety

feature, this plug will fit in a polarized outlet

only one way. If the plug does not fit fully

in the outlet, reverse the plug. If it still does

not fit, contact a qualified electrician. Do not

attempt to defeat this safety feature.

3. Never drop or insert any object into any

opening or hose.

4. Do not place the steam nozzle directly on

any surface or on the appliance power

cord while it is hot or plugged in. Use the

door hook provided.

5. This product emits hot steam during use. Do

not touch T-nozzle when product is in use.

6. Do not steam garments while on a person.

7. Before unit is turned on, the hose must be

extended and hanging on door hook.

8. Never yank cord to disconnect from outlet.

Instead, grasp plug and pull to disconnect.

9. Burns could occur from touching hot metal

parts, hot water, or steam. Use care when,

you turn a steam appliance upside down -

there may be hot water in reservoir.

10. Use caution when carrying steamer as it

contains hot water.

11. Caution: hose will be hot when in use.

Avoid prolonged contact.

SAVE THESE

INSTRUCTIONS

FOR HOUSEHOLD USE ONLY

NOT FOR COMMERCIAL OR

INDUSTRIAL USE

UNPACKING INSTRUCTIONS

Place the box on a large, sturdy flat surface.

Carefully remove the appliance from the

packing material. Keep all plastic bags away

from children.

STEAMER ASSEMBLY/DISASSEMBLY

Attaching the Steamer Hose

1. Place hose connector to unit

2. Press buttons on side

3. Place in opening and release.

locks in automatically.

Removing the Steamer Hose

(make sure unit has cooled)

To remove, just press side buttons

and pull out.

Attachments:

To add lint or crease attachments. simply

place on T-nozzle.

Hose may be stiff upon removal from box.

Hose will relax after initial use. T-handle

will sit properly on door hook once hose

is relaxed.

Hanging the t-nozzle

on the door hook

Lint Crease

GETTING TO KNOW YOUR STEAMER This steamer comes with the following

accessories:

1. Lint brush: snap onto the T-nozzle and

use before steaming to remove lint from the

fabric.

2. Crease attachment: snap onto the T-nozzle

and use to refresh creases and sleeves.

OPERATING THE STEAMER

1. Over-the-door hanger: hang this over the

top of your door and use to hang the T-noz-

zle and any garment or hanger. (Overloading

may cause deformation of door hook.)

2. Make sure the ON/OFF switch is in the

OFF position.

3. Make sure all hose connections are

secure and tight.

4. Hang the T-nozzle on the door hook.

5. Plug the cord into a normal electrical

outlet.

6. Turn the ON/OFF switch to the

ON position.

7. The switch will light to indicate when

power is on.

8. Steam will be produced from the

nozzle in about two minutes. Be sure to keep

T-nozzle on the door hook while heating up.

9. To turn steamer off, press ON/OFF switch

to the OFF position.

"T" handle steam nozzle

with stay-cool handle and

turbo steam jets

Removable

5' hose

Built-in

cord wrap

(underneath)

Water reservoir

Over-the-door

hook

Hose cap

(hang T-nozzle here)

crease attachment lint attachment

OPERATING

INSTRUCTIONS

FILLING THE WATER RESERVOIR

(PRIOR TO PLUGGING IN THE APPLIANCE)

Remove the hose cap. Fill the reservoir with

clean tap water to the desired level or until

water reaches “Max Fill” line on side of unit.

DO NOT OVERFILL as this will cause water to

boil out of steamer and spill. Empty until water

is just under the overfill indicator. DO NOT FILL

THE CONTAINER WITH HOT WATER.

For your safety and continued enjoyment of this

product, always read the instruction book

carefully before using.

CLEANING AND STORING

I. Turn the ON/OFF switch to the OFF position

and unplug from the power source.

2. Wait for the steamer to cool completely for

at least 30 minutes.

3. Unplug power cord and gently wrap around

built-in cord wrap underneath.

4. Remove excess water from the reservoir

by lifting the unit and pouring the water

down a drain.

5. Wrap hose around container and replace

T-nozzle in its cradle (as shown).

TROUBLESHOOTING THE STEAMER

• PROBLEM - No steam

CAUSE - Steamer not turned on

SOLUTION - Turn ON/OFF switch to

ON position and wait 2 minutes

• PROBLEM - Steamer fails to heat

CAUSE - Steamer not plugged in

SOLUTION - Plug into electrical outlet

• PROBLEM - No steam

CAUSE - Water level is low

SOLUTION - Turn ON/OFF switch OFF

and refill water container

• PROBLEM - Water drips from nozzle

CAUSE - Condensation in hose

SOLUTION - Hold the hose vertically

and allow water to drain back into unit

• PROBLEM - Nozzle gurgles

CAUSE - Condensation in hose

SOLUTION - Hold the hose vertically and

allow water to drain back into unit

• PROBLEM - Poor steam performance

CAUSE - Sediment in container

SOLUTION - Decalcify reservoir and

water container

Note: Minerals in water will vary in

different areas. To ensure continued oper-

ation of the steamer, never store without

cleaning and removing excess water from

the reservoir and water container.

LIMITED ONE YEAR WARRANTY

Conair will repair or replace (at our option) your

unit free of charge for 12 months from the

date of purchase if the appliance is defective

in workmanship or materials.

To obtain service under this warranty, return

the defective product to the service center

listed together with your purchase receipt and

$3.00 for postage and handling. California

residents need only provide proof of purchase

and should call 1-800-366-0937 for shipping

instructions. In the absence of a purchase

receipt, the warranty period shall be 12 months

from the date of manufacture.

ANY IMPLIED WARRANTIES, INCLUDING BUT

NOT LIMITED TO THE IMPLIED WARRANTY

OF MERCHANTABILITY AND FITNESS FOR A

PARTICULAR PURPOSE, SHALL BE LIMITED

IN DURATION TO THE 12-MONTH DURATION

OF THIS WRITTEN, LIMTED WARRANTY.

Some states do not allow limitations on how

long an implied warranty lasts, so the above

limitations may not apply to you.

IN NO EVENT SHALL CONAIR BE LIABLE

FOR ANY SPECIAL, INCIDENTAL, OR

CONSEQUENTIAL DAMAGES FOR BREACH OF

THIS OR ANY OTHER WARRANTY, EXPRESS

OR IMPLIED, WHATSOEVER. Some states do

not allow the exclusion or limitation of special,

incidental, or consequential damages, so the

above limitation may not apply to you. This

warranty gives you specific legal rights, and

you may also have other rights, which vary

from state to state.

11PA118508

NOTE

This steamer is designed to sit on the floor. Do

not put on a table or chair when in use.

OTHER IMPORTANT NOTES

During operation, the steamer hose may

gurgle. This is a normal result of condensa-

tion collecting inside the hose. Simply lift the

"T" handle upward until the hose is extended

to its full height. The gurgling will disappear

when the excess moisture inside the hose

has had a chance to drain back into the base.

HOW TO STEAM

Grasp the "T" handle steam nozzle with

the steam jets facing away from you. Begin

at the bottom of the fabric to allow the

steam to rise inside and outside, removing

wrinkles. Slowly move the nozzle from the

bottom to the top of the fabric. Remove the

nozzle from the garment and smooth the

fabric with your free hand. Some fabrics are

best steamed on the underside of the material.

This will allow the fibers of the fabric to relax,

eliminating wrinkles.

NOTE: Test fabric for color fastness in an

inconspicuous spot. Drape linens, towels,

handkerchiefs and napkins over a rod or place

onto a towel rack.

Heavier fabrics may require repeated steam-

ing. Repeat as necessary.

With practice, you will gain speed and

efficiency. You will soon learn which fabrics

require multiple steam applications.

Do not directly touch velvet or silk with the

steam head.

Always steam with hose in upright

position so any condensation is free

to flow back into the steamer.

If you steam in a low position, condensation

will collect inside the hose. This will cause

gurgling and some water droplets to form

near the steam jets on the "T" handle. To

avoid this, frequently lift the steam handle

upward until the hose is extended to its full

height.

To steam drapes:

Wash and dry drapes as directed according

to fabric type. Re-hang drapes and steam

drapes when in place.

Service Center

Conair Corporation

Service Department

7475 N. Glen Harbor Blvd.

Glendale, AZ 85307

For information on any Conair product call:

1-800-3-CONAIR or visit us on the web at

www.conair.com

Please register this product at:

www.conair.com/registration

East Windsor, NJ 08520 Glendale, AZ 85307

DECALCIFICATION

If the appliance begins to produce steam

more slowly than usual, or stops producing

steam and then starts again, you may need

to decalcify your steamer. Decalcification

refers to removing the calcium deposits

that form over time on the metal parts of

the steamer. For best performance from the

Conair Garment Steamer, decalcify the unit

from time to time. The frequency depends

upon the hardness of your tap water and how

often you use the steamer.

To decalcify, use a solution of 1/3 white

vinegar and 2/3 water in the water reservoir.

Plug the unit into electrical outlet. Turn to the

ON position and run until half the amount has

steamed. Turn the unit to the OFF position,

unplug from electrical outlet, and allow to sit

for 30 minutes.

Remove excess water from the reservoir

by lifting the unit, inverting and pouring the

water into a sink, allowing water to drain

from internal reservoir. Repeat the above

procedure as many times as necessary until

a normal steam rate returns, usually 2 to 3

times. With each repeated cycle, use a fresh

solution of vinegar and water. Run one cycle

of fresh, cold water through the unit at the

completion of decalcification before using the

unit again to steam garments.

Ready for storage

CAUTION: Hose will be hot when

in use. Avoid prolonged contact.

high-velocity steam

jet T-nozzle

Using the over-the-door hook

IB-10785

Instructions for Use

Model GS61

Convenient to use

on CLOTHES,

DRAPES & LINENS

compact

fabric

steamer

commercial quality

Specyfikacje produktu

Marka:	Conair
Kategoria:	odkurzacz parowy
Model:	GS61R

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Conair GS61R, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje odkurzacz parowy Conair

Conair ExtremeSteam GSC24PK Instrukcja

9 Października 2024

Conair CompleteSteam GS2W Instrukcja

9 Października 2024

Conair ExtremeSteam GS23X Instrukcja

8 Października 2024

Conair ExtremeSteam GS23 Instrukcja

23 Września 2024

Conair GS23 Instrukcja

23 Września 2024

Conair GS61R Instrukcja

22 Września 2024

Conair GS33R Instrukcja

22 Września 2024

Conair ExtremeSteam GS75 Instrukcja

22 Września 2024

Conair GS33 Instrukcja

22 Września 2024

Conair GS60 Instrukcja

22 Września 2024

Instrukcje odkurzacz parowy

Najnowsze instrukcje dla odkurzacz parowy

SilverCrest SFAV 3.7 A1 Instrukcja

15 Października 2024

Quigg GT-GSF-02 Instrukcja

14 Października 2024

Black & Decker BDH1725SM Instrukcja

13 Października 2024

Bissell Big Green Machine Instrukcja

10 Października 2024

G3 Ferrari Attivap G90036 Instrukcja

9 Października 2024

Cecotec Iron Professional Instrukcja

9 Października 2024

Cecotec IronHero 3000 Station Instrukcja

9 Października 2024

Cecotec Hydrosteam 1040 Active&Soap Instrukcja

9 Października 2024

VAX Steam Classic VX69 Instrukcja

9 Października 2024

VAX Steam Fresh Home Pro VX86 Instrukcja

9 Października 2024