Instrukcja obsługi Coleman QuickBed Wrap ‘N’ Roll
Coleman
dmuchany materac
QuickBed Wrap ‘N’ Roll
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Coleman QuickBed Wrap ‘N’ Roll (2 stron) w kategorii dmuchany materac. Ta instrukcja była pomocna dla 3 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek
Strona 1/2
QuickBed ® with Wrap ‘N’ Roll ™
Instructions
WARNING: Read airbed instruction manual and follow all safety instructions to avoid serious injury or death.
Not for use by children 3 and younger or people with limited mobility. They
may suffocate in a face down position or become trapped and suffocate in the gap
between the airbed and adjacent furniture or wall. If the airbed is under inflated or
deflates during use, this risk of suffocation may increase.
Do not let young children sleep on this airbed until they are mature enough
to sleep in an adult bed. Young children can suffocate on adult beds (including
airbeds), particularly when sleeping with another person. Ask your pediatrician for
specific recommendations for your child.
Adult supervision required for inflation and deflation.
This airbed can melt or burn. Keep away from open flames,
heaters, and other hot objects. Do not smoke on or near the airbed.
This airbed is not for use in water. It is not a life saving device
personal flotation device, or water toy.
This airbed is not a toy. Do not stand, walk, jump or play on the airbed.
This can result in serious injury or damage to the airbed.
Inflation Instructions
To Inflate using Coleman® QuickPumpTM Unit:
• To begin inflation, open external cap
and pull firmly on lanyard to extend out.
This will open internal yellow seal.
• Attach nozzle to inflation end of Pump.
Insert nozzle and turn on.
NEVER USE
A HAIR
DRYER TO
INFLATE
For video instructions go to
www.coleman.com/inflate
DO NOT OVER INFLATE
• When fully inflated, seal valve by pushing
in with pump nozzle. This will seal the inter-
nal yellow stopper and keep air from
escaping while closing cap.
• Fully remove pump and close external
stopper. Valve should appear depressed
into itself.
To Deflate without use of pump:
Remove adapter nozzle from inflation
end and attach to opposite deflation
side of pump. Repeat same steps as
inflation. This will draw the air out
quickly.
To deflate, open external stopper
and pull to extend out allowing air
to escape. When fully deflated close
stopper.
Important Information
• Do not let inflatable products come in contact with sharp,
pointed objects.
• Fill with cold air only. Never use a hair dryer to inflate, this
could cause melting.
• Do Not Over Inflate. Bursting items can cause serious injury.
Inflate the airbed until most of the wrinkles in the material are
gone and the bed feels firm to the touch.
Caution: Air temperature and weather do affect the air
pressure in inflatable products. In cold weather your
airbed will lose some pressure do to the fact that the air
will contract. If this occurs, you may want to add a little
air to improve your airbed’s performance. However, in
hot weather, the air will expand. You must let some air
out to prevent the airbed from failing due to overpressure.
You should avoid exposing your airbed to extreme
temperatures (hot or cold).
To Close Valve
Fully Opened Valve
• Firmly pull cap to unseat valve
from inner yellow post.
Internal
Yellow Post
Pull to Open
OPEN - STEP 2:
Internal Seal Closed
• Reverse Steps 1 & 2. Make sure
valve seats on inner yellow post.
Push to Close
Fully Closed Valve
• Close cap.
To Open / Close Valve
Internal Seal Closed
• Pull open cap.
OPEN - STEP 1:
Deflation Instructions
To Deflate using Coleman® QuickPumpTM Unit:
4010005306 (20090402)
QuickBed
®
with Wrap ‘N’ Roll™
Instructions
(continued)
Storage Steps
1. Deflate Airbed (Step 1)
(Leaving the Double LockTM Valve
open while rolling will help remove
any remaining air for more compact
storage.)
2. Fold bed as shown. (Step 2)
3. Roll up the Airbed toward the
storage flap. (Step 3)
4. Wrap storage flap around rolled bed
and tie ends to secure. (Step 4)
Sheet Clip Instructions
(applicable models only)
1. Lift up on tab to open clip and insert the edge of
sheet. (Fig. 1)
2. Insert tab into slot and push down to close. (Fig. 2)
Wrap ’N’ RollTM Storage System
Sheet Fig. 2
Slot
Sheet
Fig. 1
Tab
Please call or write us with any comments or questions.
The Coleman Company, Inc. • 3600 N. Hydraulic • Wichita, KS 67219 U.S.A.
1-800-835-3278 • TDD: 1-316-832-8707 • www.coleman.com
Sunbeam Corporation (Canada) Limited • DBA Jarden Consumer Solutions • 20B Hereford Street • Brampton, ON L6Y 0M1
1 800 387-6161
©2009 The Coleman Company, Inc. All rights reserved. Made in China.
The Coleman Company, Inc., a Jarden Corporation company (NYSE:JAH)
Coleman®, QuickBed®, , and are registered trademarks
and QuickPump™, Double Lock™, and Wrap ‘N’ Roll™ are trademarks of The Coleman Company, Inc.
Specyfikacje produktu
| Marka: | Coleman |
| Kategoria: | dmuchany materac |
| Model: | QuickBed Wrap ‘N’ Roll |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Coleman QuickBed Wrap ‘N’ Roll, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje dmuchany materac Coleman
16 Września 2024
16 Września 2024
Instrukcje dmuchany materac
- dmuchany materac Bestway
- dmuchany materac Blaupunkt
- dmuchany materac Intex
- dmuchany materac Crivit
- dmuchany materac SereneLife
- dmuchany materac Asaklitt
- dmuchany materac Active Era
- dmuchany materac Puma
- dmuchany materac Gima
Najnowsze instrukcje dla dmuchany materac
8 Października 2024
8 Października 2024
8 Października 2024
8 Października 2024
8 Października 2024
7 Października 2024
7 Października 2024
6 Października 2024
2 Października 2024
22 Września 2024