Instrukcja obsługi Citronic LS26


Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Citronic LS26 (3 stron) w kategorii Sprzęt DJ-ski. Ta instrukcja była pomocna dla 3 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/3
Line Splitter
LS26 953.022
User Manual
Features:
Switchable 2 x 6 or 1 x 12 outputs
Independent volume control per output
Dual input signal clip indicators
19” rack-mount case 1U
www.citronic.com
Introduction:
Thank you for choosing this Citronic line splitter. e LS26 provides a reliable and comprehensive solution for line signal Th
distribution. In order to achieve the best results from this equipment and avoid damage through misuse, please read and follow
these instructions and retain for future reference.
Warning:
To prevent the risk of fire or electric shock, do not expose any part of the unit to rain or moisture.
If liquids are spilled on the surface, stop using immediately, allow unit to dry out and have checked by qualified personnel before
further use.
Avoid impact, extreme pressure or heavy vibration to the unit.
There are no user serviceable parts inside the line splitter refer all servicing to qualified service personnel.
Safety
Check that the supplied mains lead is in good condition and the supply voltage is correct.
Ensure signal leads are of good condition and connected to appropriate inputs/outputs
Do not allow any foreign particles to enter the unit through control or connector apertures
Placement
Keep out of direct sunlight and away from heat sources.
Keep away from damp or dusty environments.
When rack-mounting, avoid placing heavy units above the unit and ensure all connectors and controls are accessible
Cleaning
Use a soft cloth with a neutral detergent to clean the casing as required
Use a soft brush to clear debris from the control surface
Do not use strong solvents for cleaning the unit.
Front Panel
Rear Panel
6. CHANNEL A outputs 1 6 (6.3mm jack)
7. INPUT A (6.3mm jack)
8. MONO / STEREO mode switch
9. INPUT B (6.3mm jack)
10. CHANNEL B outputs 7 12 (6.3mm jack)
11. IEC mains inlet & fuse
12. Voltage selector
1. 12) CHANNEL B volume controls (7
2. SIGNAL B input clip indicator
3. MONO / STEREO mode indicators
4. SIGNAL A input clip indicator
5. 6) CHANNEL B volume controls (1
Applications
The LS26 is a signal distribution tool which can be used to split either 2 mono signals into 6 copies of each or a single mono signal into 12 – –
copies of the original. These are boosted back up to line level and each given a volume control.
Applications for this function include
Zone level control for a venue with many rooms fed from the same stereo sound source (12 rooms for mono or 6 for stereo)
Multi-amplifier signal distribution where amplifiers have no signal-through facility
Speech distribution to headphone amplifiers for interpreters/transcribers in conference situations
Multi-level parallel processing in a studio scenario where several copies of the original are sent to various signal processors
Connection
All connections are via unbalanced 6.3mm mono jack and operate at line level. Use good quality screened jack leads to connect the input signal
to INPUT A and INPUT B (use only INPUT A if splitting a single mono signal to 12 outputs) .
Connect each output to the respective amplifier (or processor) input, again using good quality screened jack leads.
With amplifiers turned down, connect mains (ensuring correct supply voltage is selected) using the supplier IEC mains lead.
Operation
Keep amplifier volume levels turned down.
Select the required mode STEREO into 6 pairs of outputs or MONO into 12 outputs on the MODE selector switch at the rear – –
Check input signal(s) for gain level by playing the sound source into the LS26.
If the CLIP indicators light up, reduce the output level of the signal source until the clipping is eliminated.
Bring the amplifier levels back up to the maximum required level (usually full power) for the speaker(s) being driven
Control each OUTPUT via the level controls on the LS26 front panel accordingly.
After use, turn amplifiers down before switching o power to the LS26 to avoid loud noises through speakers.
SPECIFICATIONS
Power supply
115/230Vac 50/60Hz - selectable (IEC)
Inputs
A & B, (6.3mm jack)
Outputs
1 - 6 & 7 - 12 (6.3mm jack)
Input impedance
20kohm
Output impedance
220ohms
Frequency response
20Hz - 20kHz, +0/- 1dB
Signal to noise ratio
>95dB
THD
<0.008%
Dimensions
483 x 44 x 170mm
Weight
2.0kg
TROUBLESHOOTING
No function and Power switch LED is not lit
Ensure mains voltage is correct (check selector) and connected properly
Ensure mains outlet switch is on
Power is on but no audio output
Check all jack leads are OK and connected properly
Check that OUTPUT controls are not turned fully down
Check that inputs and outputs are connected the correct way around
Make sure input is connected to INPUT A in MONO mode
Check both inputs are present in STEREO mode
Distorted output
Reduce level of input source
Reduce OUTPUT level controls
Check that output is not fed to low impedance inputs in error
Output is very low level
Ensure input source is line level (0.775Vrms)
Increase OUTPUT level control(s)
Increase signal source level
Note: for further troubleshooting, refer equipment to qualified service personnel for testing
© Citronic 1201


Specyfikacje produktu

Marka: Citronic
Kategoria: Sprzęt DJ-ski
Model: LS26

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Citronic LS26, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje Sprzęt DJ-ski Citronic

Citronic

Citronic MP-X10 Instrukcja

22 Września 2024
Citronic

Citronic LS26 Instrukcja

22 Września 2024
Citronic

Citronic CEQ215 Instrukcja

21 Września 2024
Citronic

Citronic PD-1S MK2 Instrukcja

20 Września 2024
Citronic

Citronic CL22 Instrukcja

20 Września 2024
Citronic

Citronic CD-1.2 Instrukcja

18 Września 2024
Citronic

Citronic CEQ231 Instrukcja

17 Września 2024
Citronic

Citronic CE22 Instrukcja

17 Września 2024
Citronic

Citronic CX23 Instrukcja

17 Września 2024

Instrukcje Sprzęt DJ-ski

Najnowsze instrukcje dla Sprzęt DJ-ski

Festo

Festo CPX-E-CEC-M1 Instrukcja

9 Października 2024
BeamZ

BeamZ StarFuzer Instrukcja

9 Października 2024
Yamaha

Yamaha MW10 Instrukcja

8 Października 2024
Vocopro

Vocopro KRS-3808 PRO Instrukcja

7 Października 2024
Korg

Korg DT-10 Instrukcja

7 Października 2024
Nektar

Nektar CS12 Instrukcja

5 Października 2024
Ortofon

Ortofon OM 5S Instrukcja

5 Października 2024
Vocopro

Vocopro UMH-5805 Instrukcja

5 Października 2024
UDG Gear

UDG Gear Urbanite Instrukcja

5 Października 2024