Instrukcja obsługi Cisco UCS B200 M3
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Cisco UCS B200 M3 (36 stron) w kategorii serwer. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek
Strona 1/36
Americas Headquarters:
Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA
Cisco UCS B200 M3 Blade Server Installation and
Service Note
The Cisco UCS B200 M3 (shown in Figure 1) is the latest Cisco Intel-based, half-width blade supporting
two CPU sockets using Intel E5-2600 series CPUs and up to 24 DIMMs; it supports one modular LOM
(dedicated slot for Cisco's Virtual Interface Card) and one adapter card. At this time, the UCS B200 M2
(second generation) server is still available and is documented elsewhere. You can install up to eight
UCS B200 Blade Servers to a UCS chassis, mixing with other models or Cisco UCS blade servers in the
chassis if desired. The Cisco UCS B200 M3 is managed by Cisco UCS Manager version 2.0(2m) and
later.
Figure 1 Cisco UCS B200 M3 Front Panel
1 Asset tag 1
1.Each server has a blank plastic tag that pulls out of the front panel which is provided so that you can add your own
asset tracking label without interfering with the intended air flow.
7 Network link status LED
2 Blade ejector handle 8Blade health LED
3 Ejector captive screw 9Console connector
4 Hard drive bay 1 10 Reset button access
5 Hard drive bay 2 11 Beaconing LED and button
6 Power button and LED
UCS B200 M3
1 2 3 6 78 9 10 11
54
331360
2
Cisco UCS B200 M3 Blade Server Installation and Service Note
OL-26624-01
LEDs
Server LEDs indicate whether the blade server is in active or standby mode, the status of the network
link, the over all health of the blade server, and whether the server is set to give a flashing blue beaconing
indication. See Table 1 for details.
The removable hard disks also have LEDs indicating hard disk access activity and hard disk health.
Buttons
The Reset button is just inside the chassis and must be pressed using the tip of a paper clip or a similar
item. Hold the button down for five seconds, and then release it to restart the server if other methods of
restarting are not working.
Table 1 Blade Server LEDs
LED Color Description
Power Off Power off.
Green Normal operation.
Amber Standby.
Link Off None of the network links are up.
Green At least one network link is up.
Health Off Power off.
Green Normal operation.
Amber Minor error.
Blinking
Amber
Critical error.
Beaconing Off Beaconing not enabled.
Blinking
blue 1 Hz
Beaconing to locate a selected blade—If the LED is not
blinking, the blade is not selected. You can initiate
beaconing in UCS Manager or with the button.
Activity
(Disk Drive)
Off Inactive.
Green Outstanding I/O to disk drive.
Flashing
Amber
4 Hz
Rebuild in progress. Health LED will flash in unison.
Flashing
Amber
4 hz
Identify drive active.
Health
(Disk Drive)
Off Can mean either no fault detected or the drive is not
installed.
Flashing
Amber
4 hz
Identify drive active. If the Activity LED is also flashing
amber, a drive rebuild is in progress.
Amber Fault detected.
3
Cisco UCS B200 M3 Blade Server Installation and Service Note
OL-26624-01
The beaconing function for an individual server may get turned on or off by pressing the combination
button and LED. See Table 1 for details.
The power button and LED allows you to manually take a server temporarily out of service but leave it
in a state where it can be restarted quickly. If the desired power state for a service profile associated with
a blade server or an integrated rack-mount server is set to "off", using the power button or Cisco UCS
Manager to reset the server will cause the desired power state of the server to become out of sync with
the actual power state and the server may unexpected shutdown at a later time. To safely reboot a server
from a power-down state, use the Boot Server action in Cisco UCS Manager.
Connectors
The console port allows a direct connection to a blade server to allow operating system installation and
other management tasks to be done directly rather than remotely. The port uses the KVM dongle cable
(N20-BKVM shown in Figure 2) which provides a connection into a Cisco UCS blade server; it has a a
DB9 serial connector, a VGA connector for a monitor, and dual USB ports for a keyboard and mouse.
With this cable, you can create a direct connection to the operating system and the BIOS running on a
blade server. A KVM cable sh ade chassis accessory kit.ips standard with each bl
Figure 2 KVM Cable for Blade Servers
Conventions
This document uses the following conventions for notes, cautions, and safety warnings.
Notes and Cautions contain important information that you should know.
Note Means reader take note. Notes contain helpful suggestions or references to material that are not covered
in the publication.
Caution Means reader be careful. You are capable of doing something that might result in equipment damage or
loss of data.
1 3Connector to blade server slot VGA connection for a monitor
2 4DB9 serial connector 2-port USB connector for a mouse and keyboard
192621
1
23
4
Specyfikacje produktu
| Marka: | Cisco |
| Kategoria: | serwer |
| Model: | UCS B200 M3 |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Cisco UCS B200 M3, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje serwer Cisco
15 Września 2024
4 Września 2024
29 Sierpnia 2024
26 Sierpnia 2024
24 Sierpnia 2024
24 Sierpnia 2024
24 Sierpnia 2024
21 Sierpnia 2024
17 Sierpnia 2024
16 Sierpnia 2024
Instrukcje serwer
- serwer Sony
- serwer Supermicro
- serwer Lenovo
- serwer Gigabyte
- serwer Acer
- serwer Technics
- serwer Hikvision
- serwer Fujitsu
- serwer Conceptronic
- serwer StarTech.com
- serwer Asus
- serwer Medion
- serwer TRENDnet
- serwer MSI
- serwer Toshiba
- serwer D-Link
- serwer ATen
- serwer APC
- serwer HP
- serwer Tripp Lite
- serwer Moxa
- serwer Synology
- serwer Lindy
- serwer ZyXEL
- serwer Dell
- serwer Linksys
- serwer Digitus
- serwer Vimar
- serwer Netgear
- serwer Black Box
- serwer ELAC
- serwer Intellinet
- serwer HGST
- serwer Revox
- serwer Naim
- serwer SEH
- serwer Planet
- serwer NEC
- serwer LevelOne
- serwer Digi
- serwer Axis
- serwer Abus
- serwer Rocstor
- serwer Western Digital
- serwer Smart-AVI
- serwer Promise Technology
- serwer QNAP
- serwer Chenbro Micom
- serwer Allnet
- serwer Veritas
- serwer IStarUSA
- serwer Silverstone
- serwer Ernitec
- serwer AVerMedia
- serwer Atlona
- serwer Gefen
- serwer Hanwha
- serwer Quantum
- serwer Blackmagic Design
- serwer Kathrein
- serwer Eaton
- serwer Monacor
- serwer Sonnet
- serwer In Win
- serwer Teo
- serwer Megasat
- serwer Areca
- serwer Kramer
- serwer KanexPro
- serwer Raritan
- serwer AMX
- serwer C2G
- serwer Acti
- serwer Sitecom
- serwer Maxdata
- serwer Matrox
- serwer Flir
- serwer Buffalo
- serwer GeoVision
- serwer LaCie
- serwer Valcom
- serwer Asustor
- serwer Intel
- serwer Fantec
- serwer Freecom
- serwer Seagate
- serwer Iomega
- serwer Luxman
- serwer Ibm
- serwer Provision ISR
- serwer TAIDEN
- serwer SIIG
- serwer Advantech
- serwer Extron
- serwer Avocent
- serwer Silex
- serwer Sun
- serwer MvixUSA
- serwer Dual Bay
- serwer Raidsonic
- serwer EMC
- serwer Infortrend
- serwer Opengear
- serwer G-Technology
- serwer EXSYS
- serwer Middle Atlantic
- serwer Mr. Signal
- serwer Atlantis Land
- serwer Lantronix
- serwer NETSCOUT
- serwer Mobotix
- serwer Origin Storage
Najnowsze instrukcje dla serwer
14 Stycznia 2025
14 Stycznia 2025
14 Stycznia 2025
12 Stycznia 2025
11 Stycznia 2025
11 Stycznia 2025
11 Stycznia 2025
8 Stycznia 2025
1 Stycznia 2025
31 Grudnia 2025