Instrukcja obsługi Cisco Aironet 2602i

Cisco punkt dostępowy Aironet 2602i

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Cisco Aironet 2602i (40 stron) w kategorii punkt dostępowy. Ta instrukcja była pomocna dla 22 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/40

G ETTING S GTARTED UIDE

Cisco Aironet 2600 Series Access Points

July, 2012

P/N: 78-20842-01

1About this Guide

2Introduction to the Access Point

3Safety Instructions

4Unpacking

5Configurations

6Access Point Ports and Connectors

7Configuring the Access Point

8Mounting the Access Point

9Deploying the Access Point on the Wireless Network

10 Troubleshooting

11 Declarations of Conformity and Regulatory Information

12 Configuring DHCP Option 43 and DHCP Option 60

13 Access Point Specifications

1 About this Guide

This Guide provides instructions on how to install and configure your Cisco Aironet 2600 Series

Access Point. The 2600 Series Access Point is referred to as the 2600 series or the access point in this

document.

2 Introduction to the Access Point

The 2600 series supports high-performing Spectrum Intelligence which sustains three spatial stream

rates over a deployable distance with high reliability when serving clients. The 2600 series provides

high reliability and overall wireless performance.

The 2600 series offers dual-band radios (2.4 GHz and 5 GHz) with integrated and external antenna

options. The access points support full inter-operability with leading 802.11n clients, and support a

mixed deployment with other access points and controllers.

The 2600 series access point is available in both controller-based (Unified) and standalone

(Autonomous) configurations and supports:

•Simultaneous single-band or dual-band (2.4 GHz/5 GHz) radios

•Integrated antennas on 2602I access point models (AIR-CAP2602I-x-K9)

•External antennas for rugged 2602E access point models (AIR-CAP2602E-x-K9)

Note The ‘x’ in the model numbers represents the regulatory domain. Refer to “Regulatory

Domains” section on page 6 for a list of supported regulatory domains.

The features of the 2600 series are:

•Processing sub-systems (including CPUs and memory) and radio hardware which supports:

–

Network management

–

CleanAir—Automatic detection, classification, location and mitigation of RF interference

(not available on autonomous or standalone models)

–

ClientLink 2.0—BeamForming to 802.11n clients as well as legacy 802.11a/g OFDM clients

–

VideoStream

–

Location

–

WIDS/WIPS

–

Security

–

Radio Resource Management (RRM)

–

Rogue detection

–

Management Frame Protection (MFP)

–

Throughput, forwarding, and filtering performance scaled to meet 3 spatial stream, 450 Mbps

data-rates

•32 MB flash size

•802.11af/at

–

CDP (Cisco Discovery Protocol)

•2.4 GHz and 5 GHz 802.11n radios with the following features:

–

3TX x 4RX

–

3-spatial streams, 450 Mbps PHY rate

–

Spectrum intelligence

–

DPD (Digital Pre-Distortion) technology

–

Cisco Vector Beamforming—Implicit Co-phase beamforming for .11ag clients and 1

spatial-stream and 2 spatial-stream clients

–

Radio hardware is capable of explicit compressed beamforming (ECBF) per 802.11n standard

3 Safety Instructions

Translated versions of the following safety warnings are provided in the translated safety warnings

document that is shipped with your access point. The translated warnings are also in the Translated

Safety Warnings for Cisco Aironet Access Points, which is available on Cisco.com.

Warning

IMPORTANT SAFETY INSTRUCTIONS

This warning symbol means danger. You are in a situation that could cause bodily injury.

Before you work on any equipment, be aware of the hazards involved with electrical

circuitry and be familiar with standard practices for preventing accidents. Use the

statement number provided at the end of each warning to locate its translation in the

translated safety warnings that accompanied this device.

Statement 1071

SAVE THESE INSTRUCTIONS

Warning

Read the installation instructions before you connect the system to its power source.

Statement 1004

Specyfikacje produktu

Marka:	Cisco
Kategoria:	punkt dostępowy
Model:	Aironet 2602i
Kolor produktu:	Biały
Napięcie wejściowe AC:	44 - 57 V
Wysokość produktu:	221 mm
Szerokość produktu:	221 mm
Głębokość produktu:	54 mm
Waga produktu:	1040 g
Pasmo częstotliwości:	2.4, 5 GHz
Wielkość pamięci flash:	32 MB
Pojemność pamięci wewnętrznej:	256 MB
Standardy komunikacyjne:	IEEE 802.11a, IEEE 802.11b, IEEE 802.11d, IEEE 802.11g, IEEE 802.11h, IEEE 802.11i, IEEE 802.11n, IEEE 802.1x, IEEE 802.3, IEEE 802.3ab, IEEE 802.3af, IEEE 802.3u
Maksymalna szybkość przesyłania danych:	1000 Mbit/s
2,4 GHz:	Tak
5 GHz:	Tak
Prędkość transferu danych przez Ethernet LAN:	10,100,1000 Mbit/s
Ilość portów Ethernet LAN (RJ-45):	1
Umieszczenie:	Ceiling, Wall
Wewnętrzny:	Nie
Zakres temperatur (eksploatacja):	0 - 40 °C
Zakres wilgotności względnej:	10 - 90 %
Szyfrowanie / bezpieczeństwo:	802.1x RADIUS, AES, EAP-FAST, EAP-PEAP, EAP-SIM, EAP-TLS, EAP-TTLS, MSCHAPv2, TKIP, WPA, WPA2
Diody LED:	Tak
Zakres temperatur (przechowywanie):	-30 - 70 °C
Poziom wzmocnienia anteny (max):	4 dBi
Funkcje anteny:	Zintegrowana antena
Dopuszczalna wysokość podczas eksploatacji (n.p.m.):	0 - 3000 m
Wi-Fi Multimedia (WMM) / (WME):	Tak
Maksymalny transfer danych przez bezprzewody LAN:	450 Mbit/s
Dopuszczalna wysokość (n.p.m.):	0 - 4572 m