Instrukcja obsługi Chief KWD230

Chief Wandsteuna KWD230

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Chief KWD230 (16 stron) w kategorii Wandsteuna. Ta instrukcja była pomocna dla 8 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/16

Chief Manufacturing, a products division of

Milestone AV Technologies

6436 City West Parkway, Eden Prairie, MN 55344

• P: 800.582.6480 / 952.225-6000 • F:877.894.6918 / 952.894.6918

8800-002338 Rev.00

Duchossois Group Company

www.chiefmfg.com

04/13

I N S T A L L A T I O N I N S T R U C T I O N S

Small Flat Panel Mounts

Model: K-Series

This Instruction Manual covers most of the K-Series wall,

desk, and pole mounts for single, dual, and triple

displays. In addition, this Instruction Manual also covers

selected K-Series accessories.

NOTE: Some K-Series mounts, such as Extreme Tilt,

Grommet, and Table, as well as most K-Series

accessories, have separate Instruction Manuals.

See Specifications for a complete list of models

covered by this Instruction Manual.

NOTE: If an accessory such as an optional laptop tray is

being installed, complete all required installation

procedures within this document prior to installing

the accessory.

K-Series Mounts (Examples)

Model: K-Series Installation Instructions

DISCLAIMER

Milestone AV Technologies and its affiliated corporations and

subsidiaries (collectively "Milestone"), intend to make this

manual accurate and complete. However, Milestone makes no

claim that the information contained herein covers all details,

conditions or variations, nor does it provide for every possible

contingency in connection with the installation or use of this

product. The information contained in this document is subject

to change without notice or obligation of any kind. Milestone

makes no representation of warranty, expressed or implied,

regarding the information contained herein. Milestone assumes

no responsibility for accuracy, completeness or sufficiency of

the information contained in this document.

Chief® is a registered trademark of Milestone AV Technologies.

IMPORTANT SAFETY INSTRUCTIONS

WARNING: A WARNING alerts you to the possibility of

serious injury or death if you do not follow the instructions.

CAUTION: A CAUTION alerts you to the possibility of

damage or destruction of equipment if you do not follow the

corresponding instructions.

WARNING: Failure to read, thoroughly understand, and

follow all instructions can result in serious personal injury,

damage to equipment, or voiding of factory warranty! It is the

installer’s responsibility to make sure all components are

properly assembled and installed using the instructions

provided.

WARNING: Failure to provide adequate structural strength

for this component can result in serious personal injury or

damage to equipment! It is the installer’s responsibility to

make sure the structure to which this component is attached

can support five times the combined weight of all equipment.

Reinforce the structure as required before installing the

component. The wall to which the mount is being attached

may have a maximum drywall thickness of 5/8" (1.6cm). Do

not install drywall anchors into the seam between drywall

pieces.

WARNING: Exceeding the weight capacity can result in

serious personal injury or damage to equipment! It is the

installer’s responsibility to make sure the combined weight of

all components located between the K-Series mount up to

(and including) the display does not exceed the weight limit

listed in Table 1.

WARNING: Use this mounting system only for its intended

use as described in these instructions. Do not use

attachments not recommended by the manufacturer.

WARNING: Never operate this mounting system if it is

damaged. Return the mounting system to a service center for

examination and repair.

WARNING: Do not use this product outdoors.

--SAVE THESE INSTRUCTIONS--

Model: K-Series Installation Instructions

CONTENTS

TOOLS REQUIRED FOR INSTALLATION ...............................................................................................................3

SPECIFICATIONS.....................................................................................................................................................4

MOUNT INSTALLATION ...........................................................................................................................................5

DISPLAY INSTALLATION .........................................................................................................................................8

ARRAY ASSEMBLY (DUAL / TRIPLE DISPLAY; ALL EXCEPT KCY-210/-220).....................................................10

MULTI-DUAL ARM ASSEMBLY (KCY-210/-220 ONLY).......................................................................................... 11

CABLE MANAGEMENT..........................................................................................................................................12

ADJUSTMENT ........................................................................................................................................................13

TOOLS REQUIRED FOR INSTALLATION

• Phillips Screwdriver, #1 and #2

• 9/16" Wrench (KSA-1015/-1016 Only)

• Drill (All Wall Mounts)

• 1/8" Drill Bit (All Wall Mounts except KSA-1015/-1016)

• 1/4" Drill Bit (KSA-1015/-1016 Only)