Instrukcja obsługi Chauvet Festoon 2 RGB

Chauvet Maszyna efektów Festoon 2 RGB

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Chauvet Festoon 2 RGB (15 stron) w kategorii Maszyna efektów. Ta instrukcja była pomocna dla 5 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/15

I N S T A L L A T I O N I N S T R U C T I O N S

RSM Elite Series Projector Mounts

RPA Elite Series Projector Mount

RSM A-D

RSM Elite Installation InstructionsSeries Projector Mounts

DISCLAIMER

Milestone AV Technologies, and its affiliated corporations and

subsidiaries (collectively, "Milestone"), intend to make this

manual accurate and complete. However, Milestone makes no

claim that the information contained herein covers all details,

conditions or variations, nor does it provide for every possible

contingency in connection with the installation or use of this

product. The information contained in this document is subject

to change without notice or obligation of any kind. Milestone

makes no representation of warranty, expressed or implied,

regarding the information contained herein. Milestone assumes

no responsibility for accuracy, completeness or sufficiency of

the information contained in this document.

Chief® is a registered trademark of Milestone AV Technologies.

IMPORTANT SAFETY INSTRUCTIONS

WARNING: A WARNING alerts you to the possibility of

serious injury or death if you do not follow the instructions.

CAUTION: A CAUTION alerts you to the possibility of

damage or destruction of equipment if you do not follow the

corresponding instructions.

WARNING: Failure to read, thoroughly understand, and

follow all instructions can result in serious personal injury,

damage to equipment, or voiding of factory warranty! It is the

installer’s responsibility to make sure all components are

properly assembled and installed using the instructions

provided.

WARNING: Failure to provide adequate structural strength

for this component can result in serious personal injury or

damage to equipment! It is the installer’s responsibility to

make sure the structure to which this component is attached

can support five times the combined weight of all equipment.

Reinforce the structure as required before installing the

component.

WARNING: Exceeding the weight capacity can result in

serious personal injury or damage to equipment! It is the

installer’s responsibility to make sure the combined weight of

all components attached to the RSM does not exceed 25 lbs

(11.34 kg).

• The weight capacity of the RSM may be LIMITED to the

lowest weight capacity of any other components

located between the RSM and the supporting structure!

WARNING: Use this mounting system only for its intended

use as described in these instructions. Do not use

attachments not recommended by the manufacturer.

WARNING: Never operate this mounting system if it is

damaged. Return the mounting system to a service center for

examination and repair.

WARNING: Do not use this product outdoors.

IMPORTANT ! : The RSM mounts are designed to be:

• mounted to a 1-1/2" NPT or NPSM following ANSI/

ASME B1.20.1 (Schedule 40, 0.154" minimum

thickness aluminum- ASTM B221) threaded extension

column.

• mounted to double 2" x 4" wood stud cross bracing

(1-1/2" on center) between two 2" x 4" ceiling joists;

with a maximum drywall covering of 5/8".

• mounted to a concrete ceiling with a minimum

thickness of 8" and a maximum drywall covering of

5/8"; or

• suspended from four 1/4" diameter (minimum) Grade 2

or better threaded rods (not included) which are

secured to unistrut, angle or channel assembly

overhead structural members (trusses or I-beams) by

Grade 2 or better 1/4" channel nuts (not included).

NOTE: RSM Series may be used with Listed Chief models

WM110S, WM120S, WM130S, WM210S, WM220S,

WM230S, WM240S, WM210SI, WM220SI, WM230SI,

WM240SI and SL220 (not included).

--SAVE THESE INSTRUCTIONS--

Installation Instructions RSM Elite Series Projector Mounts

DIMENSIONS

5.07

128.7

1.83

46.4

ROLL ADJUSTMENT POINT

1.61

40.9

1.61

40.9

2.18

55.4

4.37

110.9

.22

5.6

2.28

BOLT CIRCLE

57.8

THREADS ONTO 1-1/2' NPT

YAW ADJUSTMENT POINT

PITCH ADJUSTMENT POINT

INTERFACE LOCKING SWITCH

NOTE: CUSTOM INTERAFCE BRACKET

NOT SHOWN. THE CUSTOM INTERFACE

BRACKET NEEDED FOR YOUR PROJECTOR

WILL ADD DEPTH TO INSTALLATION AND

THE MOUNT.

SEE SSM-XXX DRAWING ALSO.

Specyfikacje produktu

Marka:	Chauvet
Kategoria:	Maszyna efektów
Model:	Festoon 2 RGB

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Chauvet Festoon 2 RGB, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje Maszyna efektów Chauvet

Chauvet Swarm 5 FX ILS Instrukcja

23 Września 2024

Chauvet Sattelite Instrukcja

22 Września 2024

Chauvet SlimPAR Pro W USB Instrukcja

22 Września 2024

Chauvet SlimPAR Q12 BT Instrukcja

22 Września 2024

Chauvet SlimPAR 64 Wash Instrukcja

22 Września 2024

Chauvet SlimPAR H6 ILS Instrukcja

22 Września 2024

Chauvet EZLink Strip Q6 BT Instrukcja

22 Września 2024

Chauvet SlimPAR T12 BT Instrukcja

22 Września 2024

Chauvet Gobo Zoom 2 Instrukcja

22 Września 2024

Chauvet Freedom H1 Instrukcja

22 Września 2024

Instrukcje Maszyna efektów

Najnowsze instrukcje dla Maszyna efektów

BeamZ PS6W 151.262 Instrukcja

14 Stycznia 2025

BeamZ S553L Instrukcja

5 Stycznia 2025

Audibax Smoke 500 Instrukcja

5 Stycznia 2025

Audibax Haze 1200 Instrukcja

5 Stycznia 2025

Audibax Smoke 1500 Instrukcja

5 Stycznia 2025

Audibax VOLCANO 1500 RGBW Instrukcja

5 Stycznia 2025

Audibax Spark 600 Instrukcja

5 Stycznia 2025

Audibax Smoke 700 LED Instrukcja

5 Stycznia 2025

Audibax Smoke 1200 Instrukcja

5 Stycznia 2025

Audibax Geyser 2000 Instrukcja

5 Stycznia 2025