Instrukcja obsługi CE Labs HA8-4K

CE Labs odbiornik HA8-4K

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla CE Labs HA8-4K (2 stron) w kategorii odbiornik. Ta instrukcja była pomocna dla 4 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/2
WARRANTY
Cable Electronics, Inc. warrants this product to be free from defects in material and
workmanship, under normal use and service, for a period of one year from the
purchase by the original purchaser. If this product is defective or malfunctions,
Cable Electronics will replace or repair this unit (at their option) withi reasonablen a
time. No expressed or implied warranty is made for any defects caused by
immersion or exposure to liquids, abuse, neglect, improper operation of unit, excess
wear and tear and defects resulting from unauthorized disassembly and or modification.
3209 Wood Drive
Garland, TX 75041
Phone: (469) 429-9200
Toll free: (800) 767-6189
Fax: (469) 429-9205
www.celabs.net
CE labs can support many areas of your audio and video
distribution needs.
We manufacture:
- Digital Signage software and Media Players
- HD Matrix Switchers
- RF modulators
- RF amplifiers
- HDMI and Component HD distribution amplifiers
- CAT 5 Signal Extenders
- VGA Extenders and Splitters
- and cables of all types.
See our full product line at .www.celabs.net
INSTRUCTION MANUAL
Ultra High Definition
HA8-4K
.
•
• HDMI, HDCP, and DVI compatible
• Supports video resolutions up to ,4Kx2K @ 60 Hz, 4:2:0 pixel
1080p @ 60 Hz, 12-bit or 720p/1080i @ 120Hz, 12-bit
• AVI, Audio InfoFrame, and video input resolution detection
• Hardware-based HDCP error detection and recovery minimizes
firmware intervention
• Automatic output mute and unmute based on link stability,
such as cable connect/detach
• Integrated EDID in non-volatile memory and DDC support for the HDMI
ports using 256-byte SRAM for the HDMI ports
• Consumer Electronics Control (CEC) interfaces with HDMI-compliant
CEC I/O
• Supports PCM and compressed audio formats up to 192 kHz
(Dolby Digital, DTS, and AC-3)
• Supports all the mandatory and optional 3D formats up to 300 MHz
• Repeater function supports up to 127 devices
• Cascadable for retail video wall displays
• Integrated Cable retention bracket (CE labs
® patented)
Pin # Signal Pin # Signal
1 TMDS Data 2+ 11 TMDS Clock Shield
2 TMDS Data 2 Shield 12 TMDS Clock -
3 TMDS Data 2- 13 CEC
4 TMDS Data 1+ 14 Reserved (N.C )
5 TMDS Data 1 Shield 15 SCL
6 TMDS Data 1- 16 SDA
7 TMDS Data 0+ 17 DDC/CEC Ground
8 TMDS Data 0 Shield 18 +5 Power
9 TMDS Data 0- 19 Hot Plug Detect
10 TMDS Clock+
1. Turn off the devices to be connected together.
12
34
56 Input78
DC IN
HDMI SOURCE OUT 1
SPECIFICATIONS
12
34
56 Input
78
DC IN
12
34
56 Input
78
DC IN
HD MONITOR
#1
HA 8-4K HD MONITOR
#7
HD MONITOR
#8
HD MONITOR
#14
HD MONITOR
#15
HD MONITOR
#21
Model
INPUT HDMI Connector Female) (A-Type
OUTPUT HDMI Connector (A-Type Female)
Max Resolution
Cable Distance
Signal Type
Power Adapter (Min.)
Housing
Weight
Dimensions (LxWxH)
Deep Color (1080p)
Full 3D Support
HA 8-4K
HA 8-4K
INSTALLATION/OPERATION INSTRUCTIONS
Use these tabs to
secure the HDMI
cables with a
cable tie.
Note: The RJ-45 jack is for service only. This unit does not support
Ethernet or ARC.
2.
Connect HDMI cable between the the source Receiver, (DVD, Satellite etc.)
and the “HDMI In ” put port of the Distribution Amplifier.
3. Connect the HDMI cables from the outputs of the distribution amplifier to the
inputs of the monitors.
4. Power up the Distribution Amplifier and the Monitor connected to HDMI output
number one on the amplifier. Leave the other monitors off for now.
5.Turn on power to the source device. The monitor connected to output number one
should have picture and sound within about 5 seconds.
6. Turn on power to the remaining monitors.
7.
Install tie if a cable around HDMI cable and the cha sis stab desired to
prevent accidental above. unplugging of the cables. picture HDMI See
NOTES: 1. All monitors connected to the distribution amplifier should be capable of the same resolution.
2. Always connect the first monitor to output number one on the Distribution Amplifier first.
This is necessary for the Electronic ID to be read properly by the source.
3. For optimum performance, try to use HDMI cables no longer than 5 meters in length.
8-4KAH
1
8
4Kx2K @ 60 Hz, 4:2:0 pixel
6m (Max.)
HDMI V1.4 Compliant DC
DC 5V 4A
Metal
(3.5 lbs.) 1.6 Kg
15” x 6.8“ x 1.5”
12 bit
HDMI Distribution Amplifiers Cascade Configuration
HA8-4K Units may be cascaded 6 layers deep.

Specyfikacje produktu

Marka: CE Labs
Kategoria: odbiornik
Model: HA8-4K

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z CE Labs HA8-4K, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje odbiornik CE Labs

CE Labs

CE Labs HA8-4K Instrukcja

16 Września 2024
CE Labs

CE Labs HA8-4 Instrukcja

14 Września 2024

Instrukcje odbiornik

Najnowsze instrukcje dla odbiornik

Denon

Denon AVR-S900W Instrukcja

15 Października 2024
Pro-Ject

Pro-Ject Amp Box DS2 Instrukcja

15 Października 2024
AKG

AKG HP12U Instrukcja

15 Października 2024
Apart

Apart SBR160 Instrukcja

14 Października 2024
American Audio

American Audio VLP 600 Instrukcja

14 Października 2024
Chord

Chord Anni Instrukcja

14 Października 2024
Sennheiser

Sennheiser EM 9046 SU Instrukcja

14 Października 2024
Yamaha

Yamaha MusicCast RX-V481 Instrukcja

13 Października 2024
JL Audio

JL Audio VX600/6i Instrukcja

12 Października 2024
Pioneer

Pioneer SX-303RDS Instrukcja

10 Października 2024