Instrukcja obsługi CDA KA30SS
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla CDA KA30SS (3 stron) w kategorii Zlew. Ta instrukcja była pomocna dla 5 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek
Strona 1/3
www.cda.eu
ka30, ka32,
ka80 and ka82
Stainless Steel
Sinks
Installation
2
Installation
Before Installation
Oer up the sink to the worktop and/or the cabinets to confirm that
the external dimensions of the bowls are compatible with the cabinets
themselves.
Confirm that with the sink in position:
• There is adequate space to install any taps or other required
accessories.
• There is adequate space to install the waste pipework and that any
necessary modification to internal shelves to accommodate the waste
(and trap) is acceptable.
• Access to any water stop-cock or other services will still be adequate
after the installation.
Installation
• Refer to the cut-out sizes on the back of this manual and use them
to mark out where the worktop needs to be cut. Double-check the
dimensions before cutting the worktop aperture.
• After cutting out the worktop aperture, we recommend you seal the
cut edges with silicone (or similar) sealant to help prevent ingress of
water.
• Position the supplied gasket around
the perimeter of the hole (Fig. 1).
• It is often easier to mount the taps,
waste-fitting and overflow onto the sink
prior to fitting the sink to the worktop.
• Ensure that the external edge of the
sink is positioned on the gasket, to Fig. 1
3
E & O E. All instructions, dimensions and illustrations are provided for guidance only. CDA reserve the
right to change specifications without prior notice.
create a barrier to the ingress
of water and other items between sink
and worktop.
• After positioning the sink on the
worktop, position the fixing brackets
as shown in Fig. 2, then tighten their
screws.
• Do not use a power tool to tighten
the screws; by using a hand tool
it is easier to ensure that they are
tightened just enough to clamp down on the worktop and no
more.
• After fixing, remove any excess gasket material with a suitable cutter.
• We recommend a thin bead of silicone sealer is applied around the
perimeter as added protection against water ingress.
• The taps, waste-fitting and overflow can now be mounted onto the
sink (if not already done) and fully connected to their respective
services.
• To check the waste for leaks, close the plug/basket of the waste
fitting, open the tap and fill the sink to the level of the overflow; turn
o the tap and wait several minutes to verify that the water doesn’t
drain away.
• Empty the sink.
After fitting, ensure that the enclosed “Stainless Steel Sinks Use and
Maintenance” guide is retained for the customer and/or user of the
sink.
Fig. 2
Specyfikacje produktu
| Marka: | CDA |
| Kategoria: | Zlew |
| Model: | KA30SS |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z CDA KA30SS, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Zlew CDA
16 Września 2024
16 Września 2024
16 Września 2024
15 Września 2024
14 Września 2024
13 Września 2024
12 Września 2024
12 Września 2024
12 Września 2024
12 Września 2024
Instrukcje Zlew
- Zlew Teka
- Zlew Smeg
- Zlew Hendi
- Zlew Concept
- Zlew Nodor
- Zlew Hotpoint Ariston
- Zlew Artusi
- Zlew Oliveri
- Zlew Bartscher
- Zlew Franke
- Zlew Caple
- Zlew Kernau
- Zlew Foster
- Zlew Deante
- Zlew BLANCO
- Zlew Atosa
- Zlew Rangemaster
- Zlew Gustavsberg
- Zlew Leisure
- Zlew Saro
- Zlew Elkay
- Zlew Schock
- Zlew Roca
- Zlew Advance Tabco
- Zlew Eagle Group
- Zlew Sani-Lav
- Zlew Laveo
- Zlew Tot Mate
- Zlew Kuchinox
- Zlew Shaws
- Zlew Seima
Najnowsze instrukcje dla Zlew
13 Stycznia 2025
12 Stycznia 2025
2 Stycznia 2025
1 Stycznia 2025
30 Grudnia 2025
27 Grudnia 2024
27 Grudnia 2024
27 Grudnia 2024
27 Grudnia 2024
27 Grudnia 2024