Instrukcja obsługi CaviLock CL200

CaviLock Niesklasyfikowane CL200

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla CaviLock CL200 (2 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 7 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/2
CL200
Magnetic
Installation
Instructions
for Passage or
Privacy Handle
2
PAGE
BEFORE YOU START:
The door must be installed and
adjusted square to the closing
jamb for the handle to close
properly onto the striker.
INSTRUCTIONS
1. Remove handle from packaging
This handle is temporarily screwed to an aluminium
frame using the same screws (6 in total) needed to
install it to your door. As you remove the handle from the
aluminium frame, take note of how it is fitted as you will
be fitting it to your door in the reverse order (diagram a).
2. Cut out door
Mark a horizontal line on the
face of the door where the
centre of the handle is to be
positioned (diagram b).
Align the centre line on the
aluminium frame with the
centre line on the door.
Trace around the inside of the
aluminium frame as shown.
Repeat on the other side of
the door.
Transfer top and bottom lines
across the front edge of the
door.
Cut out the door along the
marked lines.
4. Fit the handle
a) Screw the wedges into the
rebates in the door as shown
( ) using the 4 x flat diagram d
head screws which were part
of the packaging.
Aluminium
frame
Transfer
across
front
edge
Mark
inner
edge of
template
Horizontal
line
Ø3mm (1/8”)
holes
35mm (1-3/8“)
deep
Drilling
template
3. Drill fixing holes
Remove the plastic drilling
template from the back of the
aluminium packaging frame.
Place the template into the
rebate with the bosses facing
towards you ( ). diagram c
Line it up on the centre of the
door thickness.
Using a Ø3mm (1⁄ 8”) drill,
spot through all six holes.
Remove the template and
drill holes to depth of 35mm
(1-3/8”).
Wedges
Flat head
screws (4)
5mm gap (1/4”)
under head
DO NOT FULLY TIGHTEN THE
SCREWS.
The underside of the
screw heads should stop
approximately 5mm (1/4”)
above the top of the wedges.
This handle IS NOT handed.
Handing is determined at time of
fitting by which way round the side
handles are fitted to the door.
DO NOT throw away the packaging
until the handle is fully fitted.
Go to page 3 (overleaf)
COMPONENTS
(Privacy Handle Shown)
Top plastic cap
Bottom plastic cap
Striker
Striker
screws (2)
Aluminium
frame
(cut out
template)
Drilling
template
Side
handle
Side
handle
Flat head
screws (4)
Face
plate
screws
(2)
Face
plate
Wedges
(2)
Snib button
(may vary)
Snib joining
pin
Alignment
pins (2)
IMPORTANT:
A. The aluminium frame is used as a template to mark out
the door cut out.
B. The rectangular plastic moulding is used as a drilling
template.
C. The bottom packaging cap has the striker fitted to it
(Privacy Handles). The snap out plastic moulding is used
to mark the striker position on the closing jamb and to
test that the lock functions correctly.
Remove the two face plate screws using a 3.5mm (9⁄64”) hex
screwdriver bit (supplied).
Pull the face plate out from between the side handles.
Remove the four remaining screws now visible after removal of
the face plate.
c
a
d
b
Alternate snib
joining pin
Hex screwdriver bit
Striker setting tool
CAVILOCK® CL200 Magnetic™ (O.D. 2017)
INSTALLATION INSTRUCTIONS.
61258/CL205ZA164 - 11.2017 © Cavity Sliders Ltd.
All copyright and other property in this document is reserved
by Cavity Sliders Limited. Details and specifications are
subject to change without notice. Whilst all care is taken
to ensure the accuracy of all information, no responsibility
will be accepted for any errors or omissions. ® CS FOR
DOORS, CS CAVITY SLIDERS and CAVILOCK are Registered
Trademarks. Patents pending.
Striker
setting
tool
Striker
Striker
screws
Striker
Slotted
hole
cavitysliders.com.au
cavitysliders.com
Mark on
closing
jamb
Cavity Sliders Ltd
Auckland Head Office
5 - 7 Rakino Way
Mt Wellington
Auckland, NZ
WARNING: THIS BOX MAY CONTAIN A STRONG MAGNET
IRON FILINGS - Magnets will attract shavings from iron or ferrous metals
which may be hard to remove. Keep the face plate a safe distance away from
these materials.
DANGER FOR CHILDREN - Magnets may cause serious injury if swallowed.
Keep out of reach of children.
CRUSHING, BLISTERS AND CUTS - Fingers may become caught between
magnets resulting in crushing, blisters or cuts.
BREAKING OR CHIPPING - It is possible that magnets could chip or shatter
on contact, resulting in chips flying off at high speed into someone’s eye.
Chips can also be very sharp - treat them as you would broken glass.
MAGNETICALLY SENSITIVE ITEMS - Keep a safe distance between the
magnet and all objects that can be damaged by magnetism (e.g. mechanical
watches, pacemakers, cell phones etc.).
DISPOSAL - Magnets should be disposed of carefully and in accordance with
your local regulations.
6. Fit the striker (Privacy Handles Only)
You will find the steel striker and fixing screws pushed onto
a snap out plastic moulding in the bottom packaging cap
( ). This striker setting tool serves two purposes:diagram a
a) Test or demo the
locking function.
Insert the striker setting tool
as shown ( ) into the diagram i
rectangular finger pull hole in
the face plate of the handle.
Hold the template in place
and push down on the snib
button.
b)Mark fixing screw positions
on the closing jamb.
With the striker setting tool
still fitted into the face plate,
close the door against the
timber closing jamb so that
the plastic plate makes a
small mark on the jamb
(diagram j).
Use this mark to fit the
bottom striker screw through
the centre of the slotted hole.
Close and latch the door to
check the alignment.
Adjust if necessary before
fitting the top striker screw.
5. Fit the face plate
With both side handles fully
tightened you can now fit the
face plate.
The open fork of the plastic
slider must slide over
the steel snib button pin
when fitting the face plate
( ) diagram h .
Lift up the snib button so that
the joining pin lines up.
Test snib action before
fastening the two face plate
screws.
Plastic
slider
Snib
joining
pin
Face
plate
Privacy Handles Only
Check that the correct length snib button joining pin is
fitted into the back of the snib button. See for Table 1
correct pin lengths. Swap with the pin in the top
packaging cap if required.
Door Thickness Alignment
Pin Length
Snib Joining
Pin Length
33 - 36 1-5/16” to 1-7/16” 31.5 1-1/4” 27.5 1-1/8”mm mm mm
37 - 40 1-1/2” to 1-9/16” 31.5 1-1/4” 31.5 1-1/4”mm mm mm
40 - 43 1-5/8” to 1-11/16” 38.5 1-1/2” 34.5 1-3/8”mm mm mm
44 - 46 1-3/4” to 1-13/16” 38.5 1-1/2” 38.5 1-1/2”mm mm mm
4. Fit the handle
b) Slide one of the side
handles under the two screw
heads as shown ( ) diagram e
checking that you have the
correct handing.
While pressing the side
handle firmly against the side
of the door fully tighten the
front screws.
Privacy
handle
shown
Privacy
handle
shown
Snib
joining
pin
Alignment
pin
c) Repeat the process with the
other side handle, taking care
to line up the alignment pins
with the two holes in the side
handles and the third hole in
the snib button (only applies
to privacy handles) (diagram f).
Bi-Parting Handles Only
Before fitting the face plate
you will need to ensure the
striker has been fitted.
Use the two screws and
washers supplied (diagram g).
Bi-Parting
face plate
Screws
& washers
Striker
4
PAGE
3
f
j
g
h
e
i
27.5
34.5
31.5
38.5
Pin Lengths
Table 1 - Pin Lengths
csfordoors.co.nz

Specyfikacje produktu

Marka: CaviLock
Kategoria: Niesklasyfikowane
Model: CL200

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z CaviLock CL200, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Niesklasyfikowane CaviLock

CaviLock

CaviLock CL200 Instrukcja

9 Października 2024

Instrukcje Niesklasyfikowane

Najnowsze instrukcje dla Niesklasyfikowane

Black Diamond

Black Diamond BD1121530000ALL1 Instrukcja

15 Października 2024
Husqvarna

Husqvarna K 970 SmartGuard Instrukcja

15 Października 2024
Stihl

Stihl HT 70 Instrukcja

15 Października 2024
Ernesto

Ernesto H14270 Instrukcja

15 Października 2024
Uniden

Uniden BT MIC KIT Instrukcja

15 Października 2024
Vaude

Vaude Omnis Bike 26 Instrukcja

15 Października 2024
ART

ART ProChannel II Instrukcja

15 Października 2024
Aukey

Aukey DR02J Instrukcja

15 Października 2024
Master Lock

Master Lock 653EURD Instrukcja

15 Października 2024
Roland

Roland FR-18 Diatonic Instrukcja

15 Października 2024