Instrukcja obsługi Carel c.pCO


Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Carel c.pCO (64 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 8 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/64
I n t e g r a t e d C o n t r o l S o l u t i o n s & E n e r g y S a v i n g s
c.pCO sistema
NO POWER
& SIGNAL
CABLES
TOGETHER
READ CAREFULLY IN THE TEXT!
Programmable Controller
User manual
3
ENG
c.pCO sistema +0300057EN rel. 1.4 - 25.10.2020
IMPORTANT
CAREL bases the development of its products on decades of experience in
HVAC, on the continuous investments in technological innovations to products,
procedures and strict quality processes with in-circuit and functional testing on
100% of its products, and on the most innovative production technology available
on the market. CAREL and its subsidiaries nonetheless cannot guarantee that all
the aspects of the product and the software included with the product respond
to the requirements of the final application, despite the product being developed
according to start-of-the-art techniques.
The customer (manufacturer, developer or installer of the final equipment) accepts
all liability and risk relating to the configuration of the product in order to reach
the expected results in relation to the specific final installation and/or equipment.
CAREL may, based on specific agreements, act as a consultant for the positive
commissioning of the final unit/application, however in no case does it accept
liability for the correct operation of the final equipment/system.
The CAREL product is a state-of-the-art product, whose operation is specified in the
technical documentation supplied with the product or can be downloaded, even
prior to purchase, from the website www.CAREL.com.
Each CAREL product, in relation to its advanced level of technology, requires setup
/ configuration / programming / commissioning to be able to operate in the best
possible way for the specific application. The failure to complete such operations,
which are required/indicated in the user manual, may cause the final product to
malfunction; CAREL accepts no liability in such cases.
Only qualified personnel may install or carry out technical service on the product.
The customer must only use the product in the manner described in the
documentation relating to the product.
In addition to observing any further warnings described in this manual, the
following warnings must be heeded for all CAREL products:
Prevent the electronic circuits from getting wet. Rain, humidity and all
types of liquids or condensate contain corrosive minerals that may damage
the electronic circuits. In any case, the product should be used or stored
in environments that comply with the temperature and humidity limits
specified in the manual.
Do not install the device in particularly hot environments. Too high
temperatures may reduce the life of electronic devices, damage them and
deform or melt the plastic parts. In any case, the product should be used
or stored in environments that comply with the temperature and humidity
limits specified in the manual.
Do not attempt to open the device in any way other than described in the
manual.
Do not drop, hit or shake the device, as the internal circuits and mechanisms
may be irreparably damaged.
Do not use corrosive chemicals, solvents or aggressive detergents to clean
the device.
Do not use the product for applications other than those specified in the
technical manual.
All of the above suggestions likewise apply to the controllers, serial boards or any
other accessory in the CAREL product portfolio.
CAREL adopts a policy of continual development. Consequently, CAREL reserves
the right to make changes and improvements to any product described in this
document without prior warning.
The technical specifications shown in the manual may be changed without prior
warning.
The liability of CAREL in relation to its products is specified in the CAREL general
contract conditions, available on the website www.CAREL.com and/or by specific
agreements with customers; specifically, to the extent where allowed by applicable
legislation, in no case will CAREL, its employees or subsidiaries be liable for any
lost earnings or sales, losses of data and information, costs of replacement
goods or services, damage to things or people, downtime or any direct, indirect,
incidental, actual, punitive, exemplary, special or consequential damage of any
kind whatsoever, whether contractual, extra-contractual or due to negligence, or
any other liabilities deriving from the installation, use or impossibility to use the
product, even if CAREL or its subsidiaries are warned of the possibility of such
damage.
DISPOSAL
DISPOSAL: INFORMATION FOR USERS
Fig. 1 Fig.2
Please read and keep.
With reference to European Union directive 2012/19/EU issued on 4 July 2012
and related national legislation, please note that:
1. Waste Electrical and Electronic Equipment (WEEE) cannot be disposed
of as municipal waste but must be collected separately so as to allow
subsequent recycling, treatment or disposal, as required by law;
2. users are required to take Electrical and Electronic Equipment (EEE) at end-
of-life, complete with all essential components, to the WEEE collection
centres identified by local authorities. The directive also provides for the
possibility to return the equipment to the distributor or retailer at end-of-
life if purchasing equivalent new equipment, on a one-to-one basis, or
one-to-zero for equipment less than 25 cm on their longest side;
3. this equipment may contain hazardous substances: improper use or
incorrect disposal of such may have negative effects on human health
and on the environment;
4. the symbol (crossed-out wheeled bin Fig.1) even if, shown on the
product or on the packaging, indicates that the equipment must be
disposed of separately at end-of-life;
5. if at end-of-life the EEE contains a battery (Fig. 2), this must be removed
following the instructions provided in the user manual before disposing
of the equipment. Used batteries must be taken to appropriate waste
collection centres as required by local regulations;
6. in the event of illegal disposal of electrical and electronic waste, the
penalties are specified by local waste disposal legislation.
Warranty on the materials: 2 years (from the date of production, excluding
consumables).
Approval: the quality and safety of CAREL INDUSTRIES Hqs products are
guaranteed by the ISO 9001 certified design and production system.
WARNING: separate as much as possible the probe and digital input signal
cables from the cables carrying inductive loads and power cables to avoid
possible electromagnetic disturbance.
Never run power cables (including the electrical panel wiring) and signal
cables in the same conduits.
NO POWER
& SIGNAL
CABLES
TOGETHER
READ CAREFULLY IN THE TEXT!
4
ENG
c.pCO sistema +0300057EN rel. 1.4 - 25.10.2020
5
ENG
c.pCO sistema +0300057EN rel. 1.4 - 25.10.2020
Content
1. INTRODUCTION 7
1.1 Functional layout ............................................................................................................................................ 8
1.2 Terminals ............................................................................................................................................................. 9
1.3 BMS port expansion cards (c.pCO Small...Extralarge) ............................................................... 9
1.4 Fieldbus port expansions cards (c.pCO Small...Extralarge) .................................................10
1.5 External modules..........................................................................................................................................10
2. DESIGN 11
2.1 c.pCO design ..................................................................................................................................................11
3. COMMUNICATION PORTS 13
3.1 Serial ports ........................................................................................................................................................13
3.2 Ethernet ports ................................................................................................................................................14
3.3 Controller network connections ........................................................................................................14
4. INSTALLATION 15
4.1 Mounting and dimensions ...................................................................................................................15
4.2 Installation ........................................................................................................................................................16
4.3 Preliminary operations ..............................................................................................................................17
4.4 Electrical connections ...............................................................................................................................17
4.5 Connecting the terminal .........................................................................................................................19
4.6 Input/output labels.....................................................................................................................................20
4.7 I/O table .............................................................................................................................................................21
4.8 c.pCOmini e c.pCOe : connections terminals .............................................................................22
4.9 c.pCO Large and Extralarge: connection terminals .......................25
5. INPUT/OUTPUT CONNECTIONS 28
5.1 Power supply ..................................................................................................................................................28
5.2 Universal inputs/outputs .........................................................................................................................28
5.3 Digital inputs ...................................................................................................................................................31
5.4 Analogue outputs ........................................................................................................................................33
5.5 Connecting the Ultracap module ......................................................................................................34
5.6 Connecting the electronic valve ........................................................................................................35
5.7 Digital outputs ...............................................................................................................................................36
5.8 Solid state relay (SSR) digital outputs .............................................................................................37
5.9 General connection diagram c.pCOmini ......................................................................................38
5.10 General connection diagram c.pCO .................................................................................................39
6. START-UP 40
6.1 Switching on ...................................................................................................................................................40
6.2 Private and shared terminal ...................................................................................................................40
6.3 Setting the controller pLAN address ................................................................................................40
6.4 Setting the terminal address and connecting the controller to the terminal ......41
6.5 Sharing terminals in a pLAN network..............................................................................................41
6.6 Uploading/updating the software ....................................................................................................42
6.7 c.pCOe expansion board: installation and configuration ...................................................45
7. SYSTEM MENU 46
7.1 Menu tree..........................................................................................................................................................46
8. PROTECTION: PASSWORD AND DIGITAL SIGNATURE MANA-
GEMENT 48
8.1 Protection features ......................................................................................................................................48
8.2 Protection Password .................................................................................................................................48
8.3 Digital signature generation .................................................................................................................49
8.4 Loading an application program on a controller signed with digital signature ...50
8.5 System menu password...........................................................................................................................50
6
ENG
c.pCO sistema +0300057EN rel. 1.4 - 25.10.2020
9. ACCESS MANAGEMENT FOR IP SERVICES 51
9.1 Accounts management ...........................................................................................................................51
9.2 Computer - c.pCO connection ............................................................................................................52
9.3 FTP connection with authentication ...............................................................................................52
9.4 HTTP connection with authentication ...........................................................................................53
10. WEB SERVER AND TERA CLOUD PLATFORM 54
10.1 Web kit download and installation ...................................................................................................54
10.2 Contents of the package .........................................................................................................................54
10.3 Web pGD ...........................................................................................................................................................54
10.4 Variables table ................................................................................................................................................54
10.5 Variable trend (logger) ..............................................................................................................................55
10.6 c.pCO connection to cloud tERA ........................................................................................................55
11. EXAMPLES 56
11.1 Devices that can be connected to the c.pCO ............................................................................58
12. TECHNICAL SPECIFICATIONS 58
12.1 c.pCO technical specifications .............................................................................................................58
12.2 FTP commands ..............................................................................................................................................63
7
ENG
c.pCO sistema +0300057EN rel. 1.4 - 25.10.2020
1. INTRODUCTION
c.pCO is a microprocessor-based, programmable electronic controller,
featuring a multitasking operating system, compatible with the c.pCO
Sistema family of devices, which includes programmable controllers, user
terminals, gateways, communication devices and remote management
devices. These devices represent a powerful control system that can be
easily interfaced with most Building Management Systems (BMS) available
on the market. The controller has been developed by CAREL to provide
solutions for several applications in air-conditioning, refrigeration and
HVAC/R in general. Its flexibility allows for creation of tailor made control
solutions according to customer specifications. Compared to pCO sistema,
the range is enhanced by a new compact controller, and consequently
comprises the c.pCOmini (4 DIN module and panel mounting version),
featuring 10 universal inputs/outputs and available with built-in driver for
single-pole electronic expansion valve, as well as the c.pCO Small, Medium,
Large, ExtraLarge models. The number of inputs/outputs can be increased
by connecting a c.pCOe expansion board.
Medium size controllers can feature also one or two built-in drivers for
electronic expansion valves. The Ultracap module (accessory) can be used
as an emergency power supply for valve drivers, so as to ensure total closure
of the valves in case of power failures (alternating current).
c.pCO can be connected in an Ethernet LAN to other c.pCO family
controllers. Each device in the LAN can exchange digital or analogue
variables with all the others, based on the application program used. c.pCO
can also be connected via a pLAN (pCO Local Area Network) to the pGD
range of terminals.
Each Fieldbus serial port, whether built into the controller or installed
via an optional card, can be connected to controlled field devices such as
valve and damper actuators and external drivers (e.g. drivers for electronic
expansion valves, EVD Evolution).
Each BMS serial port, whether built into the controller or installed via
an optional card, can be connected to field-level, automation-level
or management-level standard bus systems, such as Konnex®, LON®,
BACnet™, etc.
The real-time operating system (OS) manages priorities so as to ensure the
application program cycle time, 32-bit data and floating point numbers, and
the Ethernet multimaster and multi-protocol connection.
Main features:
optimization of the memory occupied by the Operating System and
the application program, of the boot time, of the time for loading the
application program and of the cycle time;
system response time optimization: the controller executes several
processes in parallel, each managed with a different priority;
independent processes: each process, whether a protocol, USB port
management, data and alarm log (datalogger), data exchange with
tERA cloud service, works independently of the others;
runtime debug (on target)
native management of TCP/IP multitasking protocol
Local connectivity:
built-in web server, completely customisable, supports HTML standard
and JavaScript. The 90 Mbyte memory can be used to store pages
created using the most common website development tools. Dynamic
methods (CGI, Common Gateway Interface) are available to read and
write the application program variables. Other innovative functions
include: the possibility to display the contents of the pGD1 terminal
in the browser, display graphs of data recorded by the datalogger and
plot data from probes and energy meters in real time (variable trends);
file server (FTP): the c.pCO public file system can be accessed in the
local network via FTP. Consequently, an FTP client can be used to
connect to the controller so as to upload updates, web pages and
documents. The.csv (comma separated value) files exported by the
datalogger can be downloaded
creation of accounts with different access privileges, associated to
both a webserver and an FTP server;
management of multiple simultaneous instances of Modbus TCP/IP
Master and Slave protocol;
management of BACnet™ protocol with B-BC profile (MSTP or TCP/IP,
license to be purchased separately).
Remote connectivity:
integrated connectivity to the Carel tERA cloud service: by connecting a
normal router to the controller, a secure connection can be established to
the tERA server. Remote services can be activated for the management
of control variables, alarm notification, data analysis and reports. The
connections are encrypted using the SSL (Secure Socket Layer) standard, in
compliance with NIST, international reference for information security over
the internet.
a firewall guarantees remote access only via a secure connection (tERA
cloud connection or encrypted VPN)
Integrated USB peripheral: it can be used to update the controller and
save web pages, documents and applications in the flash memory. Also
used to download the logs from the controller.
c.pCO Small...Extralarge: the host and device USB ports are managed
directly by the operating system. USB host (top): a USB flash drive can
be used to load updates (operating system/application program) on
the controller. USB device port (bottom): by connecting c.pCO to a
personal computer, its memory is made available as a removable drive,
and at the same time a communication channel is established with the
c.suite software for programming and online debugging.
c.pCOmini: the 2 USB ports are physically integrated into a single micro
USB port; the same performance is available as for the two ports on
the larger models.
Other features:
the same controller can be connected to up to 3 pGD1/pGDE terminals
(semi-graphic terminals such as pGDs or touch screens such as pGDT
/ pGDx);
external or built-in terminal with display and keypad with LED backlit
buttons, can be used for uploading software and commissioning;
universal inputs/outputs configurable via an application program,
for connecting active and passive probes, digital inputs, analogue
and PWM outputs. This extends the possibilities of configuring
inputs/outputs without having to install a larger controller;
possibility to use the c.suite software development environment,
installable on a personal computer, for creating and customising the
application program, simulating operation, supervising performance
and configuring the Ethernet network;
wide range of models that differ in terms of:
size (mini, Small, Medium, Large and Extralarge), to ensure maximum
flexibility according to the application;
digital outputs (24/230 V relay) and SSR (solid state relay);
NO or NC relay outputs
integrated optically-isolated/not optically-isolated serial ports;
optional built-in display;
various types of connectors (spring, screw, etc.).
Software programming suite, c.suite: designed as a set of independent
modules, one for each phase in HVAC/R software development, c.suite
allows teams of professionals with different skills to work in a group on
the same project, increasing efficiency and adopting joint development
based on workflow. All the software modules cooperate with each other
based on centralised data exchange, optionally managed by a software
version number (SVN):
c.strategy: environment where expert algorithm programmers prepare
the core of the application program. Features of the programming
environment:
- total independence of programming logic from the hardware and
the connected devices;
- availability of IEC 61131 standard languages: ST (structured text), FBD
(function block diagram), SFC (sequential function chart), LD (Ladder
diagram), which can also be used simultaneously;
- datatype management: 32-bit, floating point, array and native
structures;
- debug on target via USB port or Ethernet;
c.mask: dedicated environment for developers of the user interface.
c.design: denition of configurations, such as controller type and size,
type of inputs/outputs, master/slave protocols, default parameter values,
datalogger, network address and user management, connection to tERA
cloud services.
c.factory: used to program the controller, loading the application program
9
ENG
c.pCO sistema +0300057EN rel. 1.4 - 25.10.2020
1.2 Terminals
P/N Description Notes
PGDT04000F***
(tech. leaflet
+050001475)
pGD Touch 4.3” user
terminal
The pGD Touch 4.3” graphics terminal belongs to the family of touchscreen terminals, designed to
simplify and make more intuitive the interfacing of users with the controllers of the pCO Sistema
family. The electronic technology applied and the new 65,000-colour display allows the terminal
to handle high-quality images and advanced functions, providing an excellent aesthetic perfor-
mance. In addition, the touchscreen panel facilitates man-machine interaction, making it easier
to navigate through the various screens.
PGDT07000F***
(tech. leaflet
+050001490)
pGD Touch 7” user
terminal
See description of pGD Touch 4.3” user terminal.
PGDE000*
(tech. leaflet
+050001450)
pGD graphic terminal Allows complete graphics management through the use of icons (defined during the development
of the application software) and management of international fonts in two sizes: 5x7 and 11x15
pixels. The application software resides only on the c.pCO controller; the terminal requires no addi-
tional software for operation. Accessories for installation:
telephone connection cable P/N S90CONN00*;
connection cable for c.pCOmini P/N S90CONN0S0;
TCONN6J000 connection card (technical leaflet +050002895).
PLD**GFP00
(tech. leaflet
+050001840)
pLDPRO graphic
terminal
Allows complete graphics management through the use of icons (defined during the
development of the application software) and management of international fonts in two sizes:
6x8 and 12x16 pixels and audible signal via buzzer. The application software resides only on the
c.pCO controller; the terminal requires no additional software for operation, and is compatible
with graphic interfaces developed for the pGD graphic terminal. Accessories for installation:
telephone connection cable P/N S90CONN00*;
connection cable for c.pCOmini P/N S90CONN0S0;
TCONN6J000 connection card (technical leaflet +050002895).
PGD1000I00
(tech. leaflet
+050001055)
Graphic terminal
(panel installation)
This model can be installed on the panel. Its graphics properties are identical to those of the
PGDE000 terminal*. Accessories for installation:
telephone connection cable, code S90CONN00*;
TCONN6J000 shunt card (instructions sheet code +050002895).
AT*
(tech. leaflet
+0500016IE/
+0500017IE)
th-TUNE, terminal
for panel or wall
installation
Allows the user to adjust the temperature and humidity in residential environments. th-Tune is
compatible with the main wall-boxes found in many countries (Italy, U.S., Germany, China).
1.3 BMS port expansion cards (c.pCO Small...Extralarge)
P/N Description Notes
PCOS004850
(tech. leaflet
+050003237)
BMS RS485 serial
card
Can be installed on all controllers of the pCO family (except pCOB); allows direct interfacing with
an RS485 network, max. baud rate 19200. The card ensures the controller optical isolation from
the RS485 serial network.
PCO1000WB0
(tech. leaflet
+050003238)
Ethernet - pCOweb
interface card
Can be installed on all controllers of the pCO family (except pCOB); allows connecting the con-
troller to a 10 Mbps Ethernet network and provides the following functions:
access to controller data (network variables and parameters) through an Internet browser (e.g.
Internet Explorer™) installed on a PC and connected to the network via TCP/IP to pCOWeb;
connection to a supervisor network running the protocols indicated in the instructions sheet.
PCO1000BA0
(tech. leaflet
+050000930)
BACnet MS/TP -
pCOnet interface
card
Allows connecting the controller to a BACnet MS/TP (Master/Slave Token pass) network. The
RS485 connection is optically isolated from the controller.
PCO10000F0
(tech. leaflet
+050004045)
LonWorks® interface
card
Allows connecting to a LonWorks® TP/FT 10 network. The program resides in the flash memory
located in the socket, and can be programmed directly via the LonWorks® network using net-
work installation and maintenance tools such as LonMaker™. Information on how to program
the card is available in the relative manual, code +030221960.
PCOS00KXB0
(tech. leaflet
+050000770)
Konnex interface
card
Allows connecting to a network set up according to the Konnex® standard. Two versions
available: for BMS port and Fieldbus port.
10
ENG
c.pCO sistema +0300057EN rel. 1.4 - 25.10.2020
1.4 Fieldbus port expansions cards (c.pCO Small...Extralarge)
P/N Description Notes
PCO100FD10
(tech. leaflet
+050003270)
RS485 serial card Allows connecting to an RS485 network (through an electrically isolated interface). The control-
ler consequently acts as a MASTER (i.e. supervisor), therefore other controllers or devices can be
connected as SLAVES. Up to 64 devices can be connected.
PCOS00KXF0
(tech. leaflet
+050000770)
Konnex interface
card
See description of PCOS00KXB0 serial card (previous paragraph).
1.5 External modules
P/N Description Notes
PCOS00UC20
(tech. leaflet
+0500041IE)
Module
Ultracap for c.pCO
built-in driver
In case of power failures the module ensures a temporary power supply for the driver only, for
the time necessary to immediately close the electronic valves connected (one or two). This
avoids having to install a solenoid valve or backup battery kit in the refrigerant circuit.
EVD0000UC0
(tech. leaflet
+0500042IE)
Module Ultracap
external
This module, mounted on a DIN rail, can be used as alternative to the Ultracap module (PCO-
S00UC20). It can also be used in applications with a controller without built-in driver for elec-
tronic expansion valves (e.g. pCO Small + EVD Evolution + external Ultracap module). If used
with c.pCOmini, the module ensures a temporary power supply for the driver only, for the time
necessary to close the electronic valve (see technical leaflet +0500058IE)
EVD0000E*
(tech. leaflet
+050004150)
Driver for electronic
expansion valve
The driver for electronic expansion valves with two-pole stepper motor is a controller that ma-
nages refrigerant expansion in a refrigerant circuit. With the c.pCO family controllers, the version
with Modbus/Carel RS485 serial port is required. Alternatively, the driver can work in stand-alone
mode.
CPY*
(manual cod.
+040000030)
Humidification board
KUE CAREL
Used to manage an immersed electrode humidifier and share the main parameters across a
CAREL/Modbus RS485 serial line. Equipped with:
all the inputs and outputs required to completely and independently control the humidifier;
three LEDs to indicate: alarms (red), steam production (yellow), 24 Vac power supply (green);
can be connected to the CPY terminal (CPYTERM*) or to the supervisor network with Modbus®
RTU or CAREL proprietary protocol.
PCOUMI2000
(tech. leaflet
+050003210)
Interface for OEM
series humidifiers
Used to control the main parameters on CAREL OEM humidifiers directly from the c.pCO
controller. The values measured by the sensors (high level, supply water conductivity, power
consumption sensor) are converted into signals that are compatible with the inputs on the
controller.
P+E*
(tech. leaflet
+0500059IE) c.pCOe expansion
card
Used to increase the number of inputs/outputs on the controller and the number of relays.
emeter1/
emeter3
(tech. leaflet
+0500046ML/
+0500047ML)
Single-phase/three-
phase energy meter
Single-phase/three-phase energy meter with LCD to display parameters; ideal for measuring
active energy and splitting costs. Supplied with RS485 port (Modbus protocol RTU).
FCR3
(tech. leaflet
+050004065)
Three-phase speed
control
The FCR series devices are three-phase electronic voltage controllers that use phase control to
adjust the output voltage supplied to the load, based on the input signal. These devices can
control asynchronous electric motors on fans.
WS01AB2M2*
(tech. leaflet
+0500030ML)
Access point
The Access Point is part of the rTM SE system (Remote Temperature Monitoring) and allows
communication between devices via Modbus® protocol (c.pCO sistema, PlantVisor) and wireless
sensors (WS01*) or other routers (WS01*).
DPW*, DPP*, DPD*
(tech. leaflet
+050001235,
+050001245)
Serial probes
The DP* series temperature and humidity probes for rooms, service environments and duct have
been developed for the residential and light industrial HVAC/R market.
The range includes models with 0 to 10 V output and RS485 serial output (Carel or Modbus).
11
ENG
c.pCO sistema +0300057EN rel. 1.4 - 25.10.2020
2. DESIGN
2.1 c.pCO design
On the models where they are included, the front panel contains a display and a
keypad with 6 backlit buttons that, when pressed individually or in combination,
allow the following operations:
uploading an application program;
commissioning.
During regular operation and depending on the application program installed,
the terminal can be used:
to edit the main operating parameters;
to display the quantities measured, the active functions and any detected
alarm.
C1
NO1
NO2
NO3
C1
C4
NO4
NO5
NO6
C4
C7
NO7
C7
NO8
C8
NC8
NO12
C12
NC12
NO13
C13
NC13
C9
NO9
NO10
NO11
C9
G
G0
U1
U2
U3
GND
+VDC
+Vter m
GND
+5 VREF
U4
GND
U5
GND
VG
VG0
Y1
Y2
Y3
Y4
ID1
ID2
ID3
ID4
ID5
ID6
ID7
ID8
IDC1
U6
U7
U8
GND
ID9
ID10
ID11
ID12
IDC9
ID13H
ID13
IDC13
ID14
ID14H
J1 J24 J2 J3 J4 J5 J7 J8
J20
J21
J14
J10
J13J12
J22
J16 J17 J18
J15
J6
J19
NO14
C14
NC14
NO15
C15
NC15
C16
NO16
NO17
NO18
C16
ID15H
ID15
IDC15
ID16
ID16H
Y5
Y6
ID17
ID18
IDC17
U9
GND
U10
GND
Fi el dBu s ca r d BMS ca r d
J23 Fus2
J11 pLAN
J25 BMS2 J26 FBus2
4 3 2 1
AB C D
VBAT
G0
G
J30
GND
VREF
S1
S2
S3
S4
DI1
DI2
J29
on y mode ith buil l w lt-in driver
on y mode ith buil l w lt-in driver
J27
1
3
2
4
J28
1
3
2
4
A B D
H
C
G
F
E
000A5C*
L
MM N
U1
U2
U3
GND
U4
U5
U6
GND
U7
U8
U9
U10
GND
J1 J2
G
G0
Vbat
NO1
C1/2
NO2
NO3
C3/4/5
NO4
C3/4/5
NO5
NO6
NC6
C6
+5VREF
GND
+V dc
J9
J10 J11 J12
G/G0: 24 V~ 50...60 Hz / 28...36 V 30 VA/12W
J3 Disp.
+Vterm
J4 FBus
Y1
GND
ID2
ID1
Y2
GND
J8
J7
J5 CAN
L H
A
F
P
B
H
F
N
Verde/Green
Link/Act
Gia o/ e oll Y ll w
On 00Mbps = 1
O 0Mbps = 1
M
O
= 1
0Mb
ps
pane mountingl DIN rai mounting l
000A5C*
L
c.pCO mini c.pCO Sma ...Extra arge ll l
J3 Disp
+Vterm
J4 FBus
NO1
C1/2
NO2
NO3
C3/4/5
NO4
C3/4/5
NO5
NO6
NC6
C6
J10 J11 J12
U1
U2
U3
GND
U4
U5
U6
GND
U7
U8
U9
U10
GND
J1
J2
G
G0
Vbat
J7
+5VREF
GND
+V dc
J9
Y1
GND
ID2
ID1
Y2
GND
J8
J5 CAN
LH
N
M
P
Fig. 2.a
Key:
A Button to set pLAN address G Device USB port (slave)
B Display pLAN address H Main display
C Power LED L MAC address label
D Overload LED M Ethernet port
E Jumpers to select FieldBus/BMS on port J26 N Ethernet port spades
F Host USB port (master) P Single-pole valve connector
Each controller is provided with connectors for the inputs/outputs (see chap. 5) and
the secondary display, which has a button and a LED for setting the pLAN address.
Depending on the model, it can be supplied with a built-in terminal and USB ports.
Keypad
Button Descr. Backlighting Functions
Alarm White/Red pressed together with Enter, accesses the screens managed by operating system.
Prg White/Yellow -
Esc White go back up one level
UP White increase the value.
Enter White confirm the value
DOWN White decrease the value
Select pLAN
address -
pressed briefly: the pLAN address is displayed brighter
pressed repeatedly: increase the address
release: after a few seconds, the brightness is dimmed and the pLAN address is saved
Note: Once the application program is installed, all button functions depend on the program and do not necessarily correspond to the descriptions above.
12
ENG
c.pCO sistema +0300057EN rel. 1.4 - 25.10.2020
Display (c.pCO Small...Extralarge)
Two displays are available:
the main display on the built-in terminal (if featured);
the secondary display, which shows the controller pLAN address.
Display (c.pCOmini)
A built-in display is available (if featured), or a secondary display that
displays the controller pLAN address.
LED (c.pCO Small...Extralarge)
Six LEDs are featured:
1 yellow LED indicating that the device is powered;
1 red LED indicating an overload on the +VDC (J2-5) terminal;
4 LEDs indicating valve status (only on c.pCO built-in driver models).
Flashing LEDs mean the valve is moving; steady on LEDs mean the
valve is completely open or closed.
LED Colour Description
A Yellow close valve A (connector J27)
B Green open valve A (connector J27)
C Yellow close valve B (connector J28)
D Green open valve B (connector J28)
Microswitches (c.pCO Small...Extralarge)
Four microswitches are provided to configure port J26 as a Fieldbus or
BMS port (see “Port J26 configuration”).
USB ports
c.pCO Small...Extralarge
The controller features two USB ports, which can be accessed after
removing the cover in order to performe operations such as loading the
application program and the operating system, saving the logs, etc.
a “host” USB port for connecting pendrives;
a device USB port for direct connection to the USB port of a computer.
c.pCOmini
c.pCOmini models features a single micro USB port for operations such
as loading the application program and the operating system, saving the
logs, etc.
the same USB port acts both as “host” port for connecting a USB flash
drive, as well as device port for direct connection to a computer.
Mac Address label
Label with QR code containing the Mac Address that uniquely identifies
the controller on the Ethernet network
NO1
C1/2
NO2
NO3
C3/4/5
NO4
C3/4/5
NO5
NO6
NC6
C6
J10 J11 J12
J3 Disp.
+Vterm
J4 FBus J5 CAN
L H
Mac Address
Fig. 2.b
14
ENG
c.pCO sistema +0300057EN rel. 1.4 - 25.10.2020
Port J26 conguration (c.pCO Small...Extralarge)
c.pCO Small...Extralarge controllers are provided with 4 microswitches for
configuring serial port J26 (see figure):
microswitches all down: port J26 set with Fieldbus hardware;
microswitches all up: port J26 set with BMS hardware*.
Factory configuration: Fieldbus port.
(*) To use the serial port as a BMS connector, the correct communication
protocol needs to be set in the application, using the c.suite
programming environment.
C1
NO1
NO2
NO3
C1
C4
NO4
NO5
NO6
C4
NO7
C7
NO8
C8
NC8
FieldBus
4 3 2 1
BMS
1 2 3 4
BMS
FieldBus
J26
J26
Fig. 3.b
3.2 Ethernet ports
The c.pCO Small...Extralarge controllers have two 10/100 Mbps/s
Ethernet ports. These two ports are connected internally via a switch
that automatically forwards any pass-through traffic not addressed to
the controller. In the case a failure is happening in an intermediate node
(i.e power supply interruption), then the network is disconnected. The
two ports feature auto crossover (Auto-MDIX). The c.pCOmini High End
controller features one 10/100Mbps/s Ethernet port.
3.3 Controller network connections
Multimaster or Master/Slave networks of c.pCO controllers can be created
using the Ethernet ports and the serial ports:
Connection via Ethernet port
The built-in Ethernet ports on the c.pCO can be used to create multimaster
and multiprotocol networks, with transmission speeds up to 100 Mbps.
The controllers can be connected together via an external switch (see the
figure below). For c.pCO Small...Extralarge models, the two Ethernet ports
are connected by an internal hub-switch, meaning a daisy-chain network
can be created without needing an external switch (see figure 3.c).
PlantVisorPro
S itchw
J3 Disp
+Vterm
L H
J4 FBus J5 CAN J3 Disp
+Vterm
L H
J4 FBus J5 CAN
PGD terminal
touch screen
c.pCO mini
max 100 m
c.pCO mini
J25 BMS2 J26 FBus2
J11 pLAN
c. pCO
MASTER
J25 BMS2 J26 FBus2
J11 pLAN
c.pCO J25 BMS2 J26 FBus2
J11 pLAN
c.pCO
MASTER MASTER
PC
witc
J25 BMS2 J26 FBus2
J11 pLAN
c. pCO
MASTER
J25 BMS2 J26 FBus2
J11 pLAN
c.pCO J25 BMS2 J26 FBus2
J11 pLAN
c.pCO
MASTER MASTER
PC
max 100 m max 100 mmax 100 m
Fig. 3.c
Connection via serial ports:
A master/slave network of c.pCO controllers can be created by using the
RS485 serial ports. Such networks comprise:
one c.pCO controller (Master) that communicates via the Fieldbus
RS485 serial port using Carel Master or Modbus Master protocol;
one or more c.pCO controllers (Slaves) connected to the point-to-point
network via the BMS RS485 serial port using Carel Slave or Modbus
Slave protocol.
J25 BMS2 J26 FBus2
J11 pLAN
c.pCO
MASTER
J25 BMS2 J26 FBus2
J11 pLAN
c.pCO J25 BMS2 J26 FBus2
J11 pLAN
c.pCO
MASTER - SLAVE network
SLAVE SLAVE
PC
MASTER
J25 BMS2 J26 FBus2
J11 pLAN
c.pCO
J25 BMS2 J26 FBus2
J11 pLAN
c.pCO
SLAVE SLAVE
Fig. 3.d
Important warnings:
1. By applying appropriate impedance, a serial port with Master
hardware (FBus) supplies the network with the bias voltage required
to run all the connected devices, i.e. the master itself and its slaves;
conversely, serial ports with slave hardware (BMS) do not provide bias
voltage, so it is always advisable to connect at least one device with
master hardware (FBus) to the network so that it is correctly biased;
2. However, no more than two devices with master hardware (FBus)
can be connected to the same network, otherwise the network total
bias impedance becomes too small and incapable of supplying the
required voltage to the RS485 network.
3. It is recommended to connect the serial probes or other field devices
to an optically-isolated version of the Fieldbus serial port or to serial
port TWO Fieldbus 1 to exploit the filtering properties of optical
isolation.
Special cases
In networks consisting only of Master HW devices, no more than 2
devices can be connected. The max. length allowed for the network
is 1000 m. If the network is longer than 100 m, apply the 120Ω, 1/4W
terminating resistors to the first and last devices in the network;
connect the computer to a network with no more than 1 master HW
device or no more than 207 slave HW devices.
15
c.pCO
A
110
45
B
44
pGDE pGD1
156
125
67
18
30
82
202 53
43
177
70 63
110
132
45
c.pCO mini c.pCO mini, panel mounting
148
82
70.5
81.0
59.5
38.1
134
Ø 4
34.5
dima di foratura
drilling template
127x69 mm
Ø 4
ENG
c.pCO sistema +0300057EN rel. 1.4 - 25.10.2020
4. INSTALLATION
4.1 Mounting and dimensions
All models in the c.pCO family can be mounted on a DIN rail, except for
the c.pCOmini panel version.
DIN rail assembly: c.pCOmini, c.pCO Small...Extralarge
The following figure shows the dimensions of the c.pCO controllers,
according to the model.
Mounting:
place the controller on the DIN rail and press it down gently. The tabs
at the back will snap into place and lock the controller.
Removing:
lift the tabs using a screwdriver applied to their release slots. The tabs
are kept in place by springs.
Fig. 4.a
Dimensions (mm)
Small Medium Buit-in driver Large Extralarge
A227,5 315 315 315 315
B60 60 60 60 60
B - with USB port /
built-in terminal 70 70 70 70 70
B - with ULTRACAP
module - - 75 - -
Tab. 4.a
16
3
D D
DD
E
E
E
E
4a
4b
vista da dietro
controller
side
view from behind
A
B
C
C
controller
si
de
1
2
3
4
guarnizione lato a righe
striped side gasket
CLICK !
ENG
c.pCO sistema +0300057EN rel. 1.4 - 25.10.2020
Fig. 4.b
Note:
for correct assembly, follow the instructions shown in the following
diagram.
Important: when assembling, make sure that the frame is securely in
place on all four sides.
if needing to remove the frame, use a screwdriver to lever it off in slot C.
to access the USB port, open the cover B and lift the rubber cap A
using the tab
before closing the cover B again, make sure the rubber cap A is properly
inserted (it must be flush with the outer plastic surface).
if needing to cut sheet metal, it is recommended to use laser cutting;
the thickness of the sheet metal or the material used to make the
electrical panel must be suitable to ensure safe and stable installation
of the terminal;
the tension applied by the screws must not cause deformation of the
sheet metal, so as to not compromise the degree of protection (IP)
shown in the specifications. This degree of protection is guaranteed in
the following conditions: maximum deviation of rectangular opening
from flat surface0.3mm, maximum roughness of the surface where
the gasket is applied ≤ 120 m.P
4.2 Installation
Environmental conditions
Avoid installing the controller and the terminal in places with:
exposure to direct sunlight and to the elements in general;
temperature and humidity outside the product operating range (see
chapter 12, Technical Specifications”);
large, rapid fluctuations in room temperature;
strong magnetic and/or radio frequency interference (avoid installing
near transmitting antennas);
strong vibrations or knocks;
presence of explosives or flammable gas mixtures;
exposure to aggressive and polluting atmospheres (e.g. sulphur and
ammonia vapours, salt mist, fumes) that can cause corrosion and/or
oxidation;
exposure to dust (formation of a corrosive patina with possible
oxidation and reduced insulation);
exposure to water.
Positioning the controller inside the electrical panel
Install the controller inside an electrical panel in a position where it
cannot be reached and it is protected from knocks or impact. The
controller should be placed inside the panel in a position where it is
physically separated from power components (solenoids, contactors,
actuators, inverters, etc.) and their respective cables. The ideal solution
is to house these two circuits in two separate cabinets. Proximity to such
devices/cables may cause random malfunctions that are not immediately
evident. The panel casing must allow an adequate flow of cooling air.
Important:
for safety reasons the controller should be installed inside an electrical
panel so that the only accessible parts are the display and the built-in
terminal keypad;
install the controller so that the disconnect devices can be used safely
and without hindrance.
when laying out the wiring, separate as much as possible the probe
cables, digital input cables and serial line cables from the power cables,
contactors, thermomagnetic devices, in order to avoid electromagnetic
interference;
never run power cables and probe signal cables in the same conduits
(including the ones in the electrical panels);
for control signals, use shielded cables with twisted wires. If the control
cables have to cross over power cables, the intersections should be as
close as possible to 90 degrees; under no circumstances should the
control cables be laid parallel to the power cables;
keep the paths of the probe cables as short as possible and avoid
making spiral paths that enclose power devices;
in case of malfunctions do not attempt to repair the device, but
contact a CAREL service centre.
Panel installation: c.pCOmini panel version
Procedure:
1. insert the gasket, with the smooth side facing the terminal;
2. place the terminal in the opening;
3. tighten the screws;
4. apply the frame, applying uniform pressure firstly on the 4 corners
(points D) and then on the middle points of the frame (points E), until
it clicks into place.
18
ENG
c.pCO sistema +0300057EN rel. 1.4 - 25.10.2020
J3 Disp
+Vterm
L H
J4 FBus J5 CAN J3 Disp J4 FBus J6 BMS
+Vterm
J3 Disp J4 FBus J6 BMS
+Vterm
G
G0
G
G0
G
G0
24 Vac
L N
230 Vac
24 Vac
L N
J25 BMS2 J26 FBus2
J11 pLAN
c.pCO
G
G0
J25 BMS2 J26 FBus2
J11 pLAN
c.pCO
G
G0
J25 BMS2J26 FBus2
J11 pLAN
c.pCO
G
G0
Fig. 4.e
The procedure for earthing the shield is described in the corresponding
paragraph.
Case 2: multiple boards connected to a Master/Slave network powered
by different transformers (with G0 not earthed); this is a typical application
of multiple boards inside different electrical panels. If the network is more
than 100 m long, the 120 Ω, ¼ W terminating resistor is required.
J3 Disp
+Vterm
L H
J4 FBus J5 CAN J3 DispJ4 FBus J6 BMS
+Vterm
J3 Disp J4 FBus J6 BMS
+Vterm
G
G0
G
G0
G
G0
230 Vac
24 Vac
L N
230 Vac
24 Vac
L N
230 Vac
24 Vac
L N
R 20 = 1 Ω R 20 = 1 Ω
J25 BMS2 J26 FBus2
J11 pLAN
c.pCO
G
G0
J25 BMS2 J26 FBus2
J11 pLAN
c.pCO
G
G0
J25 BMS2 J26 FBus2
J11 pLAN
c.pCO
G
G0
230 Vac
24 Vac
LN
230 Vac
24 Vac
LN
230 Vac
24 Vac
LN
R 20 = 1 Ω R 20 = 1 Ω
Fig. 4.f
Important: the earth connection (if any) should be made only on
one point of the earth line (same earthing terminal for all controllers).
The procedure for earthing the shield is described in the corresponding
paragraph.
Optically-isolated serial port
This is the case of serial ONE - BMS1, serial TWO - Fieldbus 1 and the built-
in ports serials THREE and FOUR on optically-isolated models. Regardless
of the type of power supply or earthing, use a 3-wire shielded cable
connected as shown in the figure. If the network is more than 100 m
long, the terminating resistor is required.
J25 BMS2 J26 FBus2
J11 pLAN
c.pCO
G
G0
J25 BMS2 J26 FBus2
J11 pLAN
c.pCO
G
G0
J25 BMS2 J26 FBus2
J11 pLAN
c.pCO
G
G0
R 20 = 1 Ω R 20 = 1 Ω
Power
supply
Fig. 4.g
The procedure for earthing the shield is described in the corresponding
paragraph.
Procedure for earthing the shield
The shield of the serial cable is earthed differently according to the
length, as shown in the figure (where A=FBus terminal, B=BMS terminal).
Case 1: distance between controllers less than 0.3 m: earth only one end
of the cable.
L < 300 mm
L < 300 mm
A B B
Fig. 4.h
Case 2: distance between controllers greater than 0.3 m: two possibilities.
- earth one end with a bridge between the shields
L > 300 mm
L > 300 mm
A B B
Fig. 4.i
- earth both ends of the cable (no bridge between shields).
L > 300 mm
L > 300 mm
A B B
Fig. 4.j
19
ENG
c.pCO sistema +0300057EN rel. 1.4 - 25.10.2020
4.5 Connecting the terminal
c.pCOmini
Use the accessory cable P/N S90CONN0S0, connected as shown in the
figure. The maximum distance allowed without shielding is 2 meters,
from 2 to 50m a shielded cable must be used.
o
d S 0 0S0. 9 CONN B A BI NCO-WHI E/TLU = +Vterm
NE L CK/ GI LLO- ELLOW GNDRO-B A AY =
R SS RO O/ ED = +
VE DE/G EEN -R R =
J3 Disp
+Vterm
B AI NCO/WHI ET
NE O/ L CKR B A
R SS RO O/ ED
BLU
GI LLO/AYELLOW
VE DE/G EENR R
J3 Disp
+Vterm
Fig. 4.k
c.pCO Small...Extralarge
The controller and the terminal are connected to a pLAN network.
1: Connecting the terminal to one c.pCO controller
When connecting the controller to the terminal, the following restrictions
should be kept in mind:
1. the overall length of the pLAN network should not exceed 500 m.
Consequently, if the terminal is installed in a remote position, the
length of the terminal cable must be included in the total length;
2. the unshielded telephone cable can be used for a max. length of
50 m. Beyond this length, use a 3-wire shielded cable (see the table
below);
3. for lengths greater than 200 m, the power supply for the terminal
must be provided separately;
4. no more than 3 terminals (semi-graphic terminals such as pGDs or
touch screens such as pGDT / pGDx) can be connected to the same
c.pCO controller. The terminals must be the same type (e.g. all pGD1).
One terminal is powered by the controller, and the other two by an
external power supply;
5. except PGD0 / PGD1 / PGDE, other terminals must be powered with
separate power supply.
Important:
in domestic installations, standard EN55014 requires the connection
cable between the controller and the terminal to be shielded, with the
shield earthed at both ends;
in industrial installations with length >10 m, the connection cable
between the controller and the terminal must be shielded and the
shield must be earthed.
Case A: 1 terminal.
A.1: distance L < 50 m.
The typical connection for one terminal (e.g. PGD1) is made using a 6-wire
telephone cable available from CAREL as an accessory (S90CONN00*).
The telephone connector provides both data transmission and the
power supply for the terminal.
To make the connection:
plug the connector into terminal J10 until it clicks into place.
To remove the connector:
press lightly on the plastic catch on the connector and pull it out.
L < 50 m
ca o te efonicov l
te ephone cab el l
J10
J11 Lp AN
Fig. 4.l
A.2: distance 50< L< 200 m.
Lengths greater than 50 m require two TCONN6J000 cards connected
with a 4-wire shielded cable, as shown in the figure. The terminal is
powered by the controller.
J10
J11 Lp AN
L < 200 m
0 8 m MA, X
0 8 m MA, X
ca o te efonicov l
te ephone cab el l
Ca o schermatov AW 20/22G
2 twisted pair
6
+ +TX
RX
TX
RX
-
+ -
-
5 043 2 1
T 6JCONN 000
6 4 15 3 2 0 6 4 15 3 2 0
ca o te efonicov l
te ephone cab el l
Fig. 4.m
Note: for information on the position of the jumpers on the
TCONN6J000 board, see instruction sheet +050002895.
A.3: distance 200< L< 500 m.
The terminal must be powered by an external power supply. Connect
a 3-wire shielded cable to the pLAN connector (J11). Provide a separate
power supply for the TCONN6J000 card, as shown in the figure.
on/of ntf alarm e er
G
G0
U1
u2
U3
GND
+Vterm
GND
+ 5VREF
J1J24 J2
J10
J L11 pAN
L < 500 m
J 4 J -1 a dn1 5 on 2 3
on CONN T 6J000
AW /G20 22
2 is ed air wt t p
6 453 2 10
+
-
a ime alnt tore
pow ler supp y
20 30... Vd 0 mAc - 15
Fig. 4.n
Note: to reach the maximum network length, use a bus layout
with branches not exceeding 5 m.
Case B: 2 terminals
Two terminals can be directly connected only on Small models. Other
sizes require the second terminal to be powered separately. On Medium/
Large/Extralarge controllers apply configuration A.1, A.2 or A.3.
B.1: distance L < 50 m.
Use 1 TCONN6J000 card, connected as shown in the figure.
ca o te efonicov l
te ephone cab el l
J11 Lp AN
T 6JCONN 000
6 4 15 3 2 0
on/off alarm enteron/off alarm enter
0 8 m MA, X
L < 50 mL < 50 m
Fig. 4.o
20
ENG
c.pCO sistema +0300057EN rel. 1.4 - 25.10.2020
B.2 distance 50< L< 200 m.
Use 3 TCONN6J000 cards, connected as shown in the figure.
G
G0
U1
u2
U3
GND
+Vterm
GND
+ 5VREF
J1 J24 J2
J10
J11 pLAN
L < 200 m L < 200 m
6 4 15 3 2 0
ca o te efonicov l
te ephone cab el l
6 4 15 3 2 0 6 4 15 3 2 0
on/off alarm enter
on/off alarm enter
0 8 m MA, X
Fig. 4.p
B.3 distance 200< L< 500 m.
If one of the terminals is connected at a distance >200 m, connect it
according to the diagram described in A.3. Connect the other terminal as
described in A.1 or A.2. If both terminals are close to a distance > 200 m,
connect them as shown in the diagram below:
on/off ntalarm e er
on/off ntalarm e er
G
G0
U1
u2
U3
GND
+Vterm
GND
+ 5VREF
J1J24 J2
J10
J L11 pANJ31
C NAL
C NAH
GND
L < 500 m
J 4 J -1 a dn1 5 on 2 3
on CONN T 6J000
AW /G20 22
1 w tis edt pair
6 453 2 10
+
-
a aliment tore
pow ler supp y
20 30... Vd 0c - 15 mA
Fig. 4.q
Case C: 3 terminals.
For the first 2 terminals refer to Case B. For the third terminal use one of
connections A.1, A.2 or A.3.
Important:
the 24 Vdc at +Vterm (J24) can be used only in alternative to connector
J10 to power an external terminal, with maximum current 1.5 W;
in networks with a star layout, if the cable is longer than 5 m, connect
the terminal only to the first or last c.pCO in the network (to avoid
branches).
The following table applies.
type of
cable
MAX controller-
terminal distance
(m)
power supply use
TCONN6J000
card
1 telephone 50 from the controller
(150 mA)
NO
2 shielded
AWG24
200 from the controller
(150 mA)
YES
3 shielded
AWG20/22
500 separate YES
2: Shared terminal connection in pLAN network
To share a terminal between several c.pCO controllers, these can be
connected in a pLAN network, and the terminal connected to one of the
controllers in the network (see the figure below). The previous details on
the maximum length allowed between terminal and controller also apply
in this case.
J25 BMS2 J26 FBus2
J11 pLAN
c.pCO
G
G0
J25 BMS2 J26 FBus2
J11 pLAN
c.pCO
G
G0
J25 BMS2 J26 FBus2
J11 pLAN
c.pCO
G
G0
230 Vac
24 Vac
L N
230 Vac
24 Vac
L N
230 Vac
24 Vac
L N
PGD
Fig. 4.r
It is possible use one terminal only, sharing it between controllers to
display the information relating to each (see the paragraph "Private and
shared terminal").
4.6 Input/output labels
c.pCO controllers are distinguished by size and provided with inputs
and outputs and power supplies for the active probes most suitable for
various applications.
The features that depend on the model are:
maximum number and type of inputs/outputs;
availability of built-in driver for expansion valves;
type of interfaces
label Type of signal
U... Universal inputs/outputs, can be configured via software as:
Analogue inputs:
- NTC PTC, PT500, PT1000 sensors
- PT100 sensors
- 0 to 1 Vdc or 0 to 10 Vdc signals
- 0/4 to 20 mA signals
- 0 to 5 V signals for ratiometric probes
Digital inputs (not optically-isolated):
- voltage-free contacts (not optically-isolated)
- fast digital inputs
Analogue outputs (not optically-isolated):
- 0 to 10 Vdc signals
- PWM signals
Y... 0 to 10 Vdc analogue outputs, PWM outputs
ID... 24 Vac/ 24 Vdc digital input
ID...H 230 Vac digital input
NO... Relay output, normally open contact
NC... Relay output, normally closed contact
C... Relay output, common
Tx/Rx, GND Serial port
Ethernet port
Functional earth
Tab. 4.b
21
ENG
c.pCO sistema +0300057EN rel. 1.4 - 25.10.2020
4.7 I/O table
c.pCO Controllers c.pCOe I/O expansion card
mini (Basic)
mini (Enhanced)
mini (High End)
Small
Medium
Large
Extra Large
Built-in driver
Label
In/Out
Type
Basic - c.pCOe
Label
In/Out
Type
Universal
inputs/
outputs
NTC input 10 5 8 10 8 8 U In Universal I/O 10 U In Universal I/O
PTC input 10 5 8 10 8 8 U In Universal I/O 10 U In Universal I/O
PT500 input 10 5 8 10 8 8 U In Universal I/O 10 U In Universal I/O
PT1000 input 10 5 8 10 8 8 U In Universal I/O 10 U In Universal I/O
PT100 input max 5 max 2 max 3 max 4 max 3 max 3 U In Universal I/O max 5 U In Universal I/O
0 to 1 Vdc / 0 to 10 Vdc input (powered
by controller) 0
max tot 5
max 5
max tot 8
max 6
max tot 10
max 6
max tot 8
max 6
max tot 8
max 6 U In Universal I/O 0 U In Universal I/O
0 to 1 Vdc / 0 to 10 Vdc input (powered
externally)
10
(Nota1)max 5 8 10 8 8 U In Universal I/O 10
(Note1)U In Universal I/O
0 to 20 / 4 to 20 mA input (powered
by controller)
max tot 4
max 2
(Nota2)
max tot 4
max 4
max tot 7
max 6
max tot 9
max 6
max tot 7
max 6
max tot 7
max 6 U In Universal I/O
max tot 4
max 2
(Note2)U In Universal I/O
0 to 20 / 4 to 20 mA input (powered
externally) max 4 max 4 max 7 max 9 max 7 max 7 U In Universal I/O max 4 U In Universal I/O
0 to 5 V input for ratiometric probe
(+5Vref) max 2 max 5 max 6 max 6 max 6 max 6 U In Universal I/O 2 U In Universal I/O
Digital input w/ voltage-free contact 10 5 8 10 8 8 U In Universal I/O 10 U - Universal I/O
Fast digital inputs max 2 max 2 max 4 max 6 max 4 max 4 U In Universal I/O max 2 U - Universal I/O
0 to 10 Vdc output, not optically-
isolated max 5 5 8 10 8 8 U Out Universal I/O max 5 U - Universal I/O
PWM output, not optically-isolated 10 5 8 10 8 8 U Out Universal I/O 10 U - Universal I/O
max tot 10 max tot 5 max tot 8 max tot 10 max tot 8 max tot 8 max tot 10
Digital
inputs
Optically-isolated 24 Vac/Vdc input 0 8 12 14 12 12 ID In Digital input 0 ID In Digital input
24 Vac/Vdc or 230 Vac (50/60 Hz) input 0 - 2 4 2 2 ID In Digital input 0 ID In Digital input
Voltage-free contacts 0 2 - - - - - ID In Digital input 0 ID In Digital input
max tot 0 max tot 2 max tot 8 max tot 14 max tot 18 max tot 14 max tot 14 max tot 0
Analogue
outputs
0 to 10 Vdc output, optically-isolated 0 4 4 6 4 4 Y Out Analogue output 0 Y Out Analogue output
0 to 10 Vdc output, not optically-
isolated 0 2 0 0 0 0 0 Y1, Y2 Out Analogue output 0 Y1,
Y2 Out Analogue output
PWM output, optically-isolated 0 2 2 2 2 2 Y3, Y4 Out Analogue output - - -
PWM output, not optically-isolated 0 2 0 0 0 0 0 Y1, Y2 Out Analogue output 0 Y1,
Y2 Out Analogue output
Output for single-pole stepper motor 0 1 0 0 0 0 0 J7 Out Analogue output 0 J7 Out Analogue output
Output for two-pole stepper motor 0 0 0 0 0 1/2 1-3-2-4 Out Analogue output 0 - - -
max tot 0 max tot 2 max tot 4 max tot 4 max tot 6 max tot 4 max tot 6 max tot 0
Digital
outputs
NO/NC relay output 1 1 3 5 3 3 NO/NC Out Digital output 1 NO/
NC Out Digital output
NO relay output 5 7 10 13 26 10 NO Out Digital output 5 NO Out Digital output
24 V SSR output 2 1 2 3/4 2 2 NO Out Digital output 2 NO Out Digital output
230 V SSR output 2 1 2 3/4 2 2 NO Out Digital output 2 NO Out Digital output
max tot 6 max tot 8 max tot 13 max tot 18 max tot 29 max tot 13 max tot 6
16 20 25 39 52 55 41 16 Total I/O
Note 1: CAREL probes, part numbers DP**Q and DP****2, can only be used with external power supply and not powered by c.pCOmini
Note 2: excluding CAREL probes part numbers DP**Q and DP****2.
c.pCO Controllers c.pCOe I/O expansion card
mini (Basic)
mini (Enhanced)
mini (High End)
Small
Medium
Large
Extra Large
Built-in driver
Label
In/Out
Type
Basic - c.pCOe
Label
In/Out
Type
Power to terminal
0 1 1 1 1 1 J10 0 --- Telephone conn. (pLAN) J10
1 0 0 0 0 0 J3 Disp 0 Display port J3
1 1 1 1 1 1 +Vterm 0 Add. power to terminal
Power to probes 1 1 1 1 1 1 +VDC 1 Power to active probes
1 1 1 1 1 1 +5 VREF 1 Power to ratiometric probes
Power to analogue outputs 0 1 1 1 1 1 VG, VG0 0
Built-in Fieldbus ports 0 1 1 1 1 2 2 1 J23/ J26, J4 (Mini) 0
Accessory Fieldbus ports 0 1 1 1 1 1 Fbus card 0
Built-in BMS ports 0 1 0 1 1 1 1 1 J25, J6 (Mini) 1
Accessory BMS ports 0 1 1 1 1 1 BMS card 0
Host USB port 11 1 1 1 1 0
Slave USB port 1 1 1 1 1
Ethernet 0 0 1 2 2 2 2 2 0
22
C.pCO n° (03)
33,6°C
Time 12:33
date: 07.06.2013
54
1 2 3
6
8
7
Basic version
C.pCO n° (03)
33,6°C
Time 12:33
date: 07.06.2013
J6 BMS
1454
1 2 3
6
8
12
9
7
11
Enhanced version
C.pCO n° (03)
33,6°C
Time 12:33
date: 07.06.2013
C
3
3
06.
201
3
54
1 2 3
6
8
12
9 13
14
7
11
High End version
+5 VREF
GND
+V dc
J9
NO3
C3/4/5
NO4
C3/4/5
NO5
J11
NO6
NC6
C6
J12
NO1
C1/2
NO2
J10
G
G0
V bat
J1
U1
U2
U3
GND
U4
U5
U6
GND
U7
U8
U9
U10
GND
J2
J1 - G/G0: 24 V~ 50...60 Hz / 28...36 V 30 VA/12 W
J3 Disp.
+Vterm
J7
54
1 2 3
6
8
7
Basic version
ID1
ID2
GND
Y1
Y2
GND
J8
+5 VREF
GND
+V dc
J9 J7
NO3
C /4/5
NO4
C /4/5
NO5
J11
NO6
NC6
C6
J12
NO1
C1/2
NO2
J10
G
G0
V bat
J1
U1
U2
U3
GND
U4
U5
U6
GND
U7
U8
U9
U10
GND
J2
J1 - G/G0: 24 V~ 50 2 W
J3 Disp.
+Vterm
J4 FBus J6 BMS
14
12
9
11
Enhanced version
1 2 3
6
8
7
54
ID1
ID2
GND
Y1
Y2
GND
J8
+5 VREF
GND
+V dc
J9 J7
NO3
C /4/5
NO4
C /4/5
NO5
J11
NO6
NC6
C6
J12
NO1
C1/2
NO2
J10
G
G0
V bat
J1
U1
U2
U3
GND
U4
U5
U6
GND
U7
U8
U9
U10
GND
J2
J1 - G/G0: 24 V~ 50. 2 W
J3 Disp.
+Vterm
J4 FBus J5 CAN
L
1413
High End version
1 2 3
12
11
8
6
7
954
ENG
c.pCO sistema +0300057EN rel. 1.4 - 25.10.2020
4.8 c.pCOmini e c.pCOe : connections terminals
c.pCOmini - DIN rail version
Fig. 4.s
Key:
Ref. Description Ref. Description
1Power connector G(+), G0(-) 9 FieldBus connector
2Vbat: terminal for external Ultracap module (accessory) 10 BMS connector
3Universal inputs/outputs 11 Analogue outputs
4+Vterm: terminal power supply 12 Digital inputs
5Terminal connector 13 CANbus connector
6Relay digital outputs 14 Ethernet port
7Single-pole valve connector 15 Dip-Switches (only for c.pCOe)
8+5VREF: power supply for ratiometric probes
+VDC: power supply for active probes
c.pCOmini - Panel version (rear view)
23
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15 with offset
no offset
ON
OFF
Address Ext.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15 with offset
no offset
19.2 K
9.6 K
38.4 K
57.6 K
CAREL
Modbus
ON
OFF
Address Ext. ProtBaud
9
9
.
2
2
K
K
9
6
6
K
K
3
8
8.
.4
4K
K
5
7
7.
.
6K
K
C
C
AREL
M
Modbu
s
Pr
o
ot
B
a
u
u
d
ON ON Factory setting:
address = not configured
extension = no offset
Baud Rate = 19.2 K
protocol = Modbus
Basic version
Address Ext Baud Prot
15 10
1 2 3
6
8
ENG
c.pCO sistema +0300057EN rel. 1.4 - 25.10.2020
Fig. 4.t
Description of connection terminals on c.pCO mini/c.pCOe
See the figures on the previous pages relating to c.pCO mini/c.pCOe
Ref. Term. Label Description
1J1-1 G Power supply at voltage A(*)
J1-2 G0 Power supply reference
2 J1-3 Vbat Power supply from external Ultracap module
3
J2-1 U1 Universal input/output 1
J2-2 U2 Universal input/output 2
J2-3 U3 Universal input/output 3
J2-4 GND Common for universal inputs/outputs 1, 2, 3
J2-5 U4 Universal input/output 4
J2-6 U5 Universal input/output 5
J2-7 U6 Universal input/output 6
J2-8 GND Common for universal inputs/outputs 4, 5, 6
J2-9 U7 Universal input/output 7
J2-10 U8 Universal input/output 8
J2-11 U9 Universal input/output 9
J2-12 U10 Universal input/output 10
J2-13 GND Common for universal inputs/outputs 7, 8, 9, 10
4 J3-1 +Vterm Power supply for additional terminal
5
J3-2 Tx-/Rx- Terminal RS485 port Tx-/Rx-
J3-3 Tx+/Rx+ Terminal RS485 port Tx+/Rx+
J3-4 GND Terminal RS485 port GND
6
J10-1 NO1 Normally open contact, relay 1
J10-2 C1/2 Common for relay 1, 2
J10-3 NO2 Normally open contact, relay 2
J11-1 NO3 Normally open contact, relay 3
J11-2 C3/4/5 Common for relay 3, 4, 5
J11-3 NO4 Normally open contact, relay 4
J11-4 C3/4/5 Common for relay 3, 4, 5
J11-5 NO5 Normally open contact, relay 5
J12-1 NO6 Normally open contact, relay 6
J12-2 NC6 Normally closed contact, relay 6
J12-3 C6 Common for relay 6
7 J7 - Single-pole valve connector
8
J9-1 +5 VREF Power supply ratiometric probes 0 to 5 V
J9-2 GND Power supply common
J9-3 +VDC Power to active probes
Ref. Term. Label Description
9
J4-1 Tx-/Rx- FieldBus RS485 port Tx-/Rx-
J4-2 Tx+/Rx+ FieldBus RS485 port Tx+/Rx+
J4-3 GND FieldBus RS485 port GND
10
J6-1 Tx-/Rx- BMS RS485 port Tx-/Rx-
J6-2 Tx+/Rx+ BMS RS485 port Tx+/Rx+
J6-3 GND BMS RS485 port GND
11
J8-4 Y1 Analogue output 1, 0...10 V
J8-5 Y2 Analogue output 2, 0...10 V
J8-6 GND Common for analogue outputs 1, 2
12
J8-1 ID1 Digital input 1
J8-2 ID2 Digital input 2
J8-3 GND Common for digital inputs 1, 2
13
J5-1 TxL/RxL CANbus port TxL/RxL
J5-2 TxH/RxH CANbus port TxH/RxH
J5-3 GND CANbus port GND
(*) Voltage A: 24 Vac o 28...36 Vdc
c.pCOe - DIN rail version
24
SMALL
C1
NO1
NO2
NO3
C1
C4
NO4
NO5
NO6
C4
C7
NO7
C7
NO8
C8
NC8
G
G0
U1
U2
U3
GND
+VDC
U4
GND
U5
GND
VG
VG0
Y1
Y2
Y3
Y4
ID1
ID2
ID3
ID4
ID5
ID6
ID7
ID8
IDC1
J1 J2 J3 J4 J5
J14
J10
J13J12 J15
drac SMBdrac suBdleiF
4 3 2 1
Tx/Rx
J11 pLAN
GND
J25 BMS2
Tx/RxGND Tx/RxGND
J26 FBus2
+Vterm
GND
+5VREF
J24
+
XXXXXXXXXXXX
26
25
18
17
12 1327 14 Mac address 15
16
10 11
45
1 6
2 3 3 7 8
28
C1
NO1
NO2
NO3
C1
C4
NO4
NO5
NO6
C4
C7
NO7
C7
NO8
C8
NC8
G
G0
U1
U2
U3
GND
+VDC
U4
GND
U5
GND
VG
VG0
Y1
Y2
Y3
Y4
ID1
ID2
ID3
ID4
ID5
ID6
ID7
ID8
IDC1
J1 J2 J3 J4 J5
J14
J10
J13J12 J15
drac SMBdrac suBdleiF
4 3 2 1
Tx/Rx
J11 pLAN
GND
J25 BMS2
Tx/RxGND Tx/RxGND
J26 FBus2
+Vterm
GND
+5VREF
J24
+
XXXXXXXXXXXX
NO12
C12
NC12
NO13
C13
NC13
C9
NO9
NO10
NO11
C9
U6
U7
U8
GND
ID9
ID10
ID11
ID12
IDC9
ID13H
ID13
IDC13
ID14
ID14H
J7
J8
J16 J17 J18
J6
8 9
MEDI MU
15
3
26
25
18
17
12 1327 14 Mac address 15
16
10 11
4 51 62 3 3 7 8
28
ENG
c.pCO sistema +0300057EN rel. 1.4 - 25.10.2020
4.1 c.pCO Small and Medium: connection terminals
Fig. 4.u
Key:
Ref. Description Ref. Description
1 Power conncetion G(+), G0(-) 12 Reserved
2+Vterm: power supply for additional terminal
+5 VREF power supply for ratiometric probes 13 Ethernet port 1
3 Universal inputs/outputs 14 Ethernet port 2
4 +VDC: power supply for active probes 15 Relay digital outputs
5 Button for setting pLAN address, second display, LED 16 BMS2 port
6VG: power supply at voltage A(*) for opto-isolated analogue output
VG0: power to optically-isolated analogue output, 0 Vac/Vdc 17 FieldBus2 port
7 Analogue outputs 18 Jumpers for selecting FieldBus/ BMS
8 ID: digital inputs for voltage A (*) 25 USB Host Port (Master)
9ID..: digital inputs for voltage A (*)
IDH..: digital inputs for voltage B (**) 26 USB Device Port (Slave)
10 pLAN telephone connector for terminal 27 Faston for earth connection to Ethernet Port
11 pLAN plug-in connector 28 Display built-in and keypad
(*) Tensione A: 24 Vac o 28...36 Vdc; (**) Tensione B: 230 Vac - 50/60 Hz.
25
C1
NO1
NO2
NO3
C1
C4
NO4
NO5
NO6
C4
C7
NO7
C7
NO8
C8
NC8
G
G0
U1
U2
U3
GND
+VDC
U4
GND
U5
GND
VG
VG0
Y1
Y2
Y3
Y4
ID1
ID2
ID3
ID4
ID5
ID6
ID7
ID8
IDC1
J1 J2 J3 J4 J5
J14
J10
J13
J12 J15
drac SMBdrac suBdleiF
4 3 2 1
Tx/Rx
J11 pLAN
GND
J25 BMS2
Tx/Rx GND Tx/Rx GND
J26 FBus2
+Vterm
GND
+5VREF
J24
+
XXXXXXXXXXXX
U6
U7
U8
GND
J20
J21 J22
J16 J17 J18
J6
J19
NO14
C14
NC14
NO15
C15
NC15
C16
NO16
NO17
NO18
C16
ID15H
ID15
IDC15
ID16
ID16H
Y5
Y6
ID17
ID18
IDC17
U9
GND
U10
GND
J23 FBus2
3 8 9
1915
93 8
LARGE
C9
NO9
NO10
NO11
C9
NO12
C12
NC12
NO13
C13
NC13
ID9
ID10
ID11
ID12
IDC9
J7
ID13H
ID13
IDC13
ID14
ID14H
J8
Tx/Rx GND
7
15
26
25
12 1327 14 Mac address 15
16
10 11
45
1 6
2 3 3 7 8
28
18
17
EXTRALARGE
C25
NO25
NO26
NO27
NO28
NO29
C25
J20
C21
NO21
NO22
NO23
NO24
C21
15
C17
NO17
NO18
NO19
NO20
C17
J19
C1
NO1
NO2
NO3
C1
C4
NO4
NO5
NO6
C4
C7
NO7
C7
NO8
C8
NC8
G
G0
U1
U2
U3
GND
+VDC
U4
GND
U5
GND
VG
VG0
Y1
Y2
Y3
Y4
ID1
ID2
ID3
ID4
ID5
ID6
ID7
ID8
IDC1
J1 J2 J3 J4 J5
J14
J10
J13J12 J15
drac SMBdrac suBdleiF
4 3 2 1
Tx/Rx
J11 pLAN
GND
J25 BMS2
Tx/Rx GND Tx/Rx GND
J26 FBus2
+Vterm
GND
+5VREF
J24
+
XXXXXXXXXXXX
C14
NO14
NO15
NO16
C14
U6
U7
U8
GND
J21 J22
J16 J17 J18
J6
J23 FBus2
3 8 9
19
15
C9
NO9
NO10
NO11
C9
NO12
C12
NC12
NO13
C13
NC13
ID9
ID10
ID11
ID12
IDC9
J7
ID13H
ID13
IDC13
ID14
ID14H
J8
Tx/Rx GND
26
25
12 1327 14 Mac address 15 15
16
10 11
4 51 62 3 3 7 8
28
18
17
ENG
c.pCO sistema +0300057EN rel. 1.4 - 25.10.2020
4.9 c.pCO Large and Extralarge: connection terminals
Fig. 4.v
Key:
Ref. Description Ref. Description
1 Power connector G(+), G0(-) 13 Ethernet port 1
2+Vterm: power supply for additional terminal
+5 VREF power supply for ratiometric probes 14 Ethernet port 2
3 Universal inputs/outputs 15 Relay digital outputs
4 +VDC: power supply for active probes 16 BMS2 port
5 Button for setting pLAN address, second display, LED 17 FieldBus2 port
6VG: power supply at voltage A(*) for opto-isolated analogue output
VG0: power to optically-isolated analogue output, 0 Vac/Vdc 18 Jumpers for selecting FieldBus/ BMS
7 Analogue outputs 19 FieldBus2 port
8 ID: digital inputs for voltage A (*) 25 USB Host Port (Master)
9ID..: digital inputs for voltage A (*)
IDH..: digital inputs for voltage B (**) 26 USB Device Port (Slave)
10 pLAN telephone connector for terminal/downloading application 27 Faston for earth connection to Ethernet Port
11 pLAN plug-in connector 28 Display built-in and keypad
12 Reserved
(*) Voltage A: 24 Vac or 28-36 Vdc; (**) Voltage B: 230 Vac - 50/60 Hz.
26
C1
NO1
NO2
NO3
C1
C4
NO4
NO5
NO6
C4
C7
NO7
C7
NO8
C8
NC8
G
G0
U1
U2
U3
GND
+VDC
U4
GND
U5
GND
VG
VG0
Y1
Y2
Y3
Y4
ID1
ID2
ID3
ID4
ID5
ID6
ID7
ID8
IDC1
J1 J2 J3 J4 J5
J14
J10
J13J12 J15
drac SMBdrac suBdleiF
4 3 2 1
Tx/Rx
J11 pLAN
GND
J25 BMS2
Tx/Rx GND Tx/Rx GND
J26 FBus2
+Vterm
GND
+5VREF
J24
+
XXXXXXXXXXXX
A B C D
NO12
C12
NC12
NO13
C13
NC13
C9
NO9
NO10
NO11
C9
U6
U7
U8
GND
J8
J16 J17 J18
J6
3 8 9
22 24
20 21
J27
1
3
2
4
J28
1
3
2
4
driver
VBAT
G0
G
J30
23
GND
VREF
S1
S2
S3
S4
DI1
DI2
J29
B ILT - IN DRIVERU
ID13H
ID13
IDC3
ID14
ID14H
ID9
ID10
ID11
ID12
IDC9
J7
15
26
25
18
17
12 1327 14 Mac address 15
16
10 11
4 51 62 3 3 7 8
28
ENG
c.pCO sistema +0300057EN rel. 1.4 - 25.10.2020
4.2 c.pCO built-in driver: connection terminals
Two models of c.pCO are available with one or two built-in electronic expansion valve drivers.
Fig. 4.w
Key:
Ref. Description Ref. Description
1 Power connctor G(+), G0(-) 15 Relay digital outputs
2+Vterm: power supply for additional terminal
+5 VREF power supply for ratiometric probes 16 BMS2 port
3 Universal inputs/outputs 17 FieldBus2 port
4 +VDC: power supply for active probes 18 Jumpers for selecting FieldBus/ BMS
5 Button for setting pLAN address, second display, LED 20 Electronic valve A connector
6VG: power supply at voltage A(*) for opto-isolated analogue output
VG0: power to optically-isolated analogue output, 0 Vac/Vdc 21 Electronic valve B connector
7 Analogue outputs 22 Connector for external Ultracap module (accessory)
8 ID: digital inputs for voltage A (*) 23 Valve driver analogue and digital inputs
9ID..: digital inputs for voltage A (*)
IDH..: digital inputs for voltage B (**) 24 Valve status indicator LED
10 pLAN telephone connector for terminal 25 USB Host Port (Master)
11 pLAN plug-in connector 26 USB Device Port (Slave)
12 Reserved 27 Faston for earth connection to Ethernet Port
13 Ethernet port 1 28 Display built-in and keypad
14 Ethernet port 2
(*) Voltage A: 24 Vac or 28-36 Vdc; (**) Voltage B: 230 Vac - 50/60 Hz.
Description of connection terminals on c.pCO Small... Extralarge
Ref. Term. Label Description
1J1-1 G Power supply at voltage A(*)
J1-2 G0 Power supply reference
2
J24-1 +Vterm Additional power supply terminal
J24-2 GND Power supply common
J24-3 +5 VREF Power supply ratiometric probes 0 to 5 V
3
J2-1 U1 Universal input/output 1
J2-2 U2 Universal input/output 2
J2-3 U3 Universal input/output 3
J2-4 GND Common for universal inputs/outputs 1, 2, 3
3
J3-1 U4 Universal input/output 4
J3-2 GND Common for universal input/output 4
J3-3 U5 Universal input/output 5
J3-4 GND Common for universal input/output 5
3
J6-1 U6 Universal input/output 6
J6-2 U7 Universal input/output 7
J6-3 U8 Universal input/output 8
J6-4 GND Common for universal inputs/outputs 6, 7, 8
Ref. Term. Label Description
3
J20-3 U9 Universal input/output 9i
J20-4 GND Common for universal input/output 9i
J20-5 U10 Universal input/output 10i
J20-6 GND Common for universal input/output 10i
4 J2-5 +VDC Power to active probes
5 Button for setting pLAN address, secondary display, LED
6
J4-1 VG Power to optically-isolated analogue output,
voltage A(*)
J4-2 VG0 Power to optically-isolated analogue output, 0
Vac/Vdc
7
J4-3 Y1 Analogue output 1, 0 to 10 V
J4-4 Y2 Analogue output 2, 0 to 10 V
J4-5 Y3 Analogue output 3, 0 to 10 V
J4-6 Y4 Analogue output 4, 0 to 10 V
7J20-1 Y5 Analogue output 5, 0 to 10 Vi
J20-2 Y6 Analogue output 6, 0 to 10 Vi
27
ENG
c.pCO sistema +0300057EN rel. 1.4 - 25.10.2020
Ref. Term. Label Description
8
J5-1 ID1 Digital input 1 at voltage A(*)
J5-2 ID2 Digital input 2 at voltage A(*)
J5-3 ID3 Digital input 3 at voltage A(*)
J5-4 ID4 Digital input 4 at voltage A(*)
J5-5 ID5 Digital input 5 at voltage A(*)
J5-6 ID6 Digital input 6 at voltage A(*)
J5-7 ID7 Digital input 7 at voltage A(*)
J5-8 ID8 Digital input 8 at voltage A(*)
J5-9 IDC1 Common for digital inputs from 1 to 8 (negative
pole for DC power supply)
8
J7-1 ID9 Digital input 9 at voltage A(*)
J7-2 ID10 Digital input 10 at voltage A(*)
J7-3 ID11 Digital input 11 at voltage A(*)
J7-4 ID12 Digital input 12 at voltage A(*)
J7-5 IDC9 Common for digital inputs from 9 to 12 (negative
pole for DC power supply
8
J20-7 ID17 Digital input 17 at voltage A(*)i
J20-8 ID18 Digital input 18 at voltage A(*)i
J20-9 IDC17iCommon for digital inputs 17 and 18 (negative
pole for DC power supply
9
J8-1 ID13H Digital input 13 at voltage B(**)
J8-2 ID13 Digital input 13 at voltage A(*)
J8-3 IDC13 Common for digital inputs 13 and 14 (negative
pole for DC power supply)
J8-4 ID14 Digital input 14 at voltage A(*)
J8-5 ID14H Digital input 14 at voltage B(**)
9
J19-1 ID15H Digital input 15 at voltage B(**)i
J19-2 ID15 Digital input 15 at voltage A(*)i
J19-3 IDC15iCommon for digital inputs 15 and 16 (negative
pole for DC power supply)
J19-4 ID16 Digital input 16 at voltage A(*)i
J19-5 ID16H Digital input 16 at voltage B(**)i
10 J10 - Connector for telephone cable pLAN
11
J11-1 Tx-/Rx- pLAN RS485 port Tx-/Rx-
J11-2 Tx+/Rx+ pLAN RS485 port Tx+/Rx+
J11-3 GND pLAN RS485 port GND
12 - - Reserved
13 - - Ethernet port 1
14 - - Ethernet port 2
15
J12-1 C1 Common for relays 1, 2, 3
J12-2 NO1 Normally open contact, relay 1
J12-3 NO2 Normally open contact, relay 2
J12-4 NO3 Normally open contact, relay 3
J12-5 C1 Common for relay 1, 2, 3
J13-1 C4 Common for relay 4, 5, 6
J13-2 NO4 Normally open contact, relay 4
J13-3 NO5 Normally open contact, relay 5
J13-4 NO6 Normally open contact, relay 6
J13-5 C4 Common for relay 4, 5, 6
J14-1 C7 Common for relay 7
J14-2 NO7 Normally open contact, relay 7
J14-3 C7 Common for relay 7
J15-1 NO8 Normally open contact, relay 8
J15-2 C8 Common for relay 8
J15-3 NC8 Normally closed contact 8
J16-1 C9 Common for relay 9, 10, 11
J16-2 NO9 Normally open contact, relay 9
J16-3 NO10 Normally open contact, relay 10
J16-4 NO11 Normally open contact, relay 11
J16-5 C9 Common for relay 9, 10, 11
J17-1 NO12 Normally open contact, relay 12
J17-2 C12 Common for relay 12
J17-3 NC12 Normally closed contact 12
J18-1 NO13 Normally open contact, relay 13
J18-2 C13 Common for relay 13
J18-3 NC13 Normally closed contact 13
J21-1 NO14 Normally open contact, relay 14i
J21-2 C14 Common for relay 14i
J21-3 NC14 Normally closed contact 14i
J21-4 NO15 Normally open contact, relay 15i
J21-5 C15 Common for relay 15i
J21-6 NC15 Normally closed contact 15i
J22-1 C16 Common for relay 16, 17, 18i
J22-2 NO16 Normally open contact, relay 16i
J22-3 NO17 Normally open contact, relay 17i
J22-4 NO18 Normally closed contact 18i
J22-5iC16 Common for relay 16, 17, 18
J21-1 C14 Common for relay 14, 15, 16ii
J21-2 NO14 Normally open contact, relay 14ii
J21-3 NO15 Normally open contact, relay 15ii
J21-4 NO16 Normally open contact, relay 16ii
J21-5 C14 Common for relay 14, 15, 16ii
Ref. Term. Label Description
15
J22-1 C17 Common for relay 17, 18, 19, 20ii
J22-2 NO17 Normally open contact, relay 17ii
J22-3 NO18 Normally open contact, relay 18ii
J22-4 NO19 Normally open contact, relay 19ii
J22-5 NO20 Normally open contact, relay 20ii
J22-6 C17 Common for relay 17, 18, 19, 20ii
J19-1 C21 Common for relay 21, 22, 23, 24ii
J19-2 NO21 Normally open contact, relay 21ii
J19-3 NO22 Normally open contact, relay 22ii
J19-4 NO23 Normally open contact, relay 23ii
J19-5 NO24 Normally open contact, relay 24ii
J19-6 C21 Common for relay 21, 22, 23, 24ii
J20-1 C25 Common for relay 25, 26, 27, 28, 29ii
J20-2 NO25 Normally open contact, relay 25ii
J20-3 NO26 Normally open contact, relay 26ii
J20-4 NO27 Normally open contact, relay 27ii
J20-5 NO28 Normally open contact, relay 28ii
J20-6 NO29 Normally open contact, relay 29ii
J20-7 C25 Common for relay 25, 26, 27, 28, 29ii
16
J25-1 Tx-/Rx- Tx-/Rx- RS485 BMS2 port
J25-2 Tx+/Rx+ Tx+/Rx+ RS485 BMS2 port
J25-3 GND GND RS485 BMS2 port
17 J26-1 Tx-/Rx- Tx-/Rx- RS485 Fieldbus 2 port
J26-2 Tx+/Rx+ Tx+/Rx+ RS485 Fieldbus 2 port
18 Port J26 configuration microswitches
19
J23-1 Tx-/Rx- Tx-/Rx- Fieldbus 2 RS485 port
J23-2 Tx+/Rx+ Tx+/Rx+ Fieldbus 2 RS485 port
J23-3 GND GND RS485 port network Fieldbus 2
For pCO5+ built-in driver only:
20
J27-1 1
Electronic expansion valve 1 control (see par.
“Electronic valve connection”).
J27-2 3
J27-3 2
J27-4 4
21
J28-1 1
Electronic expansion valve 2 control (see par.
“Electronic valve connection”).
J28-2 3
J28-3 2
J28-4 4
22
J30-1 VBAT
Power supply from external Ultracap moduleJ30-2 G0
J30-3 G
23
J29-1 GND Common probe power supply
J29-2 VREF Probe driver power supply
J29-3 S1 Probe 1
J29-4 S2 Probe 2
J29-5 S3 Probe 3
J29-6 S4 Probe 4
J29-7 DI1 Digital input 1
J29-8 DI2 Digital input 2
24 A, B Valve A status LED
C, D Valve B status LED
Tab. 4.c
(*): voltage A: 24 Vac or 28...36 Vdc;
(**): voltage B: 230 Vac - 50/60 Hz.
i: Large model; ii: Extralarge model
28
ENG
c.pCO sistema +0300057EN rel. 1.4 - 25.10.2020
5. INPUT/OUTPUT CONNECTIONS
5.1 Power supply
The figure below shows the power supply connection diagram. Use
a class II safety isolation transformer with short-circuit and overload
protection. See the Technical Specifications table for information on the
size of the transformer required by each model (see chap. 13).
2 Vac4
230 Vac
2.5 A T
G
G0
J1
28...3 Vdc6
2.5 A T
G
G0
J1
-+
AC DC
Fig. 5.a
Important:
power the c.pCO built-in driver with AC voltage only, with the
transformer secondary winding earthed;
if the Ethernet connection is featured and used, the transformer
secondary must be earthed;
using a supply voltage other than specified can seriously damage the
controller;
if the transformer secondary is earthed, make sure that the earth
conductor is connected to terminal G0. This applies to all the devices
connected to the c.pCO through a serial network;
if more than one c.pCO board is connected to a pLAN network, make
sure that the G and G0 references are observed (G0 must be maintained
for all controllers);
the power supply to the controller(s) and the terminal(s) should be
kept separate from the power supply to the other electrical devices
(contactors and other electromechanical components) inside the
electrical panel.
Note:
when the controller is powered, the yellow LED lights up;
refer to the diagrams in par. 4.4 in case of controllers connected to a
pLAN network and installed in the same electrical panel or in separate
panels.
5.2 Universal inputs/outputs
Universal inputs/outputs are distinguished by the letter U...
They can be configured from the application program for many different
uses, such as the following:
passive temperature probes: NTC, PTC, PT100, PT500, PT1000;
active pressure/temperature/humidity probes;
ratiometric pressure probes;
current inputs, 0 to 20 mA or 4 to 20 mA;
voltage inputs, 0 to 1 Vdc or 0 to 10 Vdc;
voltage-free contact digital inputs and fast digital inputs;
analogue outputs, 0 to 10 Vdc;
PWM outputs.
Important:
the universal inputs/outputs must be pre-configured to handle their
respective signals from the application program;
the universal inputs/outputs cannot be used as digital outputs.
Max. number of connectable analogue inputs
The maximum number of analogue inputs that can be connected to the
universal inputs/outputs depends on the type used.
Maximum number of inputs connectable to universal inputs/outputs
Type of signal c.pCO
mini -
c.pCOe
Small Medium/ Built-in
driver/ Extralarge
Large
Analogue inputs
- NTC/PTC/
PT500/PT1000
probes
10 5 8 10
- PT100 probes max 5 2 3 (2 on U1...U5, 1
on U6...U8)
4 (2 on U1...U5, 1 on
U6...U8, 1 on U9...
U10)
- 0 to 1 Vdc/0
to 10 Vdc
signals from
probes po-
wered by the
controller
0
max tot 5
5
max tot 8
6
max tot 10
max 6
- 0 to 1 Vdc/0
to 10 Vdc si-
gnals powered
externally
10 5 8 10
- 0 to 20 mA
/4 to 20 mA
inputs from
probes po-
wered by the
controller
max tot 4
2
max tot 4
4
max tot 7
6:
(max 4 on U1...
U5,
3 on U6...U8)
max tot 9
6:
(max 4 on U1...
U5,
3 on U6...U8,
2 on U9...U10)
- 0 to 20 mA
/ 4 to 20 mA
inputs from
probes powe-
red externally
4 4 7:
(max 4 on U1...
U5,
3 on U6...U8)
9:
(max 4 on U1...
U5,
3 on U6...U8,
2 on U9...U10)
- 0 to 5 V
signals from
ratiometric
probes po-
wered by the
controller
max 2 max 5 max 6 max 6
Tab. 5.a
Note: the table shows the maximum number of inputs that can be
connected. For example, it is possible to connect to a Small size controller
a maximum of five 0 to 1Vdc inputs related to probes powered by the
controller, and a a maximum of five 0 to 1 Vdc inputs related to probes
powered externally. In any case, maximum number of 0 to 1Vdc inputs
must be 5.
Remote connection of analogue inputs
The table below shows the required cable sizes to be used for the remote
connection of the analogue inputs.
Type of input Cross section for lengths
<50 m (mm2)
Cross section for lengths
<100 m (mm2)
NTC 0,5 1,0
PT1000 0,75 1,5
I (current) 0,25 0,5
V (current) 0,25 0,5
Tab. 5.b
Important:
if the controller is installed in an industrial environment (standard
EN 61000-6-2) the connections must be less than 10 m long; do not
exceed this length to avoid measurement errors.
to avoid electromagnetic interference, keep the probe and digital
input cables separate from the power cables as much as possible (at
least 3 cm). Never run power cables and probe signal cables in the
same conduits (including the ones in the electrical panels).
29
ENG
c.pCO sistema +0300057EN rel. 1.4 - 25.10.2020
Connecting NTC, PTC temperature probes
For information on the maximum number of probes that can be
connected see the table at the beginning of this paragraph. For details
on the operating range see the Technical Specifications table (cap. 12).
G
G0
U1
U2
U3
GND
+VDC
+Vterm
GND
+5 VREF
U4
GND
U5
GND
VG
VG0
Y1
Y2
Y3
Y4
ID1
ID2
ID3
ID4
ID5
ID6
J1 J24 J2 J3 J4 J5
F ie ld Bus c ar d B MS car d
U1
U2
U3
GND
+VDC
U4
GND
U5
GND
1
23
4
Fig. 5.b
Key
Controller terminals
NTC probe
1 2 3 4
GND Wire 1
U1 Wire 2
GND Wire 1
U2 Wire 2
GND Wire 1
U4 Wire 2
GND Wire 1
U5 Wire 2
Connecting PT500/PT1000 temperature probes
For information on the maximum number of probes that can be
connected see the table at the beginning of this paragraph. For
details on the operating range see the Technical Specifications table
(cap. 12).
Important:
to ensure correct measurements from the probe each wire must be
connected to only one terminal.
the two probe wires have no polarity.
G
G0
U1
U2
U3
GND
+VDC
+Vterm
GND
+5 VREF
U4
GND
U5
GND
VG
VG0
Y1
Y2
Y3
Y4
ID1
ID2
ID3
ID4
ID5
ID6
J1 J24 J2 J3 J4 J5
F ie ld Bus c ar d B MS car d
input: 24 V 50...60 Hz / 28...36 V
max. power: 45 VA/20 W
U1
U2
U3
GND
+VDC
U4
GND
U5
GND
1
2
Fig. 5.c
Key
Controller terminals PT500/PT1000 probe
1 2
GND Wire 1
U4 Wire 2
GND Wire 1
U5 Wire 2
Connecting PT100 temperature probes
For information on the maximum number of probes that can be
connected see the table at the beginning of this paragraph. For details on
the operating range see the Technical Specifications table (see chap. 12).
The probe has three wires: connect one to GND and the other two to two
separate but adjacent universal inputs on the same controller (e.g. U1, U2,
GND, or U4, U5, GND).
G
G0
U1
U2
U3
GND
+VDC
+Vterm
GND
+5 VREF
U4
GND
U5
GND
VG
VG0
Y1
Y2
Y3
Y4
ID1
ID2
ID3
ID4
ID5
ID6
J1 J24 J2 J3 J4 J5
F ie ld Bus c ar d B MS car d
U1
U2
U3
GND
+VDC
U4
GND
U5
GND
12
Fig. 5.d
Key
Controller terminals PT100 probe
1 2
U1 Wire 1 (red)
U2 Wire 2 (red)
GND Wire 3 (white)
U4 Wire 1 (red)
U5 Wire 2 (red)
GND Wire 3 (white)
Connecting active temperature and humidity probes
For information on the maximum number of probes that can be connected
see the table at the beginning of this paragraph. The number depends on
the power supply used. The distinction is between probes powered by the
controller (terminal +VDC) and probes powered by an external source, and
also between active probes with voltage or current outputs. For details
on the operating range see the data sheets supplied with the probes. The
controller can be connected to all the CAREL DP* series active temperature
and humidity probes configured for 0 to 1 V or 4 to 20 mA.
Note: in c.pCOmini models it is not possible to manage 0 to 1 Vdc
or 0 to 10 Vdc signals coming from probes powered directy by the
controller.
Important: for temperature probes use the 4 to 20 mA or NTC
configuration, cause 0 to 1 Vdc signal is limited to the 0 to 1 V range and
is therefore not always compatible with the standard 10 mV/°C signal of
CAREL probes (at temperatures below 0 °C or above 100 °C a probe alarm
may be activated).
G
G0
U1
U2
U3
GND
+VDC
+Vterm
GND
+5 VREF
U4
GND
U5
GND
VG
VG0
Y1
Y2
Y3
Y4
ID1
ID2
ID3
ID4
ID5
ID6
J1 J24 J2 J3 J4 J5
F ie ld Bus c ar d B MS car d
U1
U2
U3
GND
+VDC
M
out T
+ (G)
out H
Fig. 5.e
Key
Controller terminals Probe terminals Description
GND M Reference
+VDC +(G) Probe power supply
U1 outH Humidity probe output
U2 outT Temperature probe output
30
ENG
c.pCO sistema +0300057EN rel. 1.4 - 25.10.2020
Connecting current-output pressure probes
For information on the maximum number of probes that can be connected
see the table at the beginning of this paragraph. For details on the operating
range see the data sheets supplied with the probes. The controller can
be connected to all CAREL SPK* series active pressure probes or any
commercially available pressure probes with 0 to 20 mA or 4 to 20 mA signals.
G
G0
U1
U2
U3
GND
+VDC
+Vterm
GND
+5 VREF
U4
GND
U5
GND
VG
VG0
Y1
Y2
Y3
Y4
ID1
ID2
ID3
ID4
J1 J24 J2 J3 J4
F ie ld Bus c ar d B MS ca r d
U1
U2
U3
GND
+VDC
U4
GND
U5
GND
1
1
2
21
2
Fig. 5.f
Key
Controller
terminals
Current-output pressure probe
1 2
+VDC Wire 1 power brown Wire 1 power brown
U1 Wire 2 Signal white -
U2 Wire 2 Signal white
Connecting 0 to 5 V ratiometric pressure probes
For information on the maximum number of probes that can be
connected see the table at the beginning of this paragraph. For details
on the operating range see the probe data sheets. The controller can
be connected to all CAREL SPKT series active pressure probes or any
commercially available pressure probes with 0 to 5 V ratiometric signals.
Important:
ratiometric probes are powered by the controller via terminal +5 VREF;
ratiometric probes cannot be powered by an external source.
G
G0
U1
U2
U3
GND
+VDC
+Vterm
GND
+5 VREF
U4
GND
U5
GND
VG
VG0
Y1
Y2
Y3
Y4
ID1
J1 J24 J2 J3 J4
F ie ld Bus c ar d B MS car d
U1
U2
U3
GND
GND
+ VREF5
+VDC
Fig. 5.g
Key
Controller terminals Description Wire colour
+5 Vref Power black
GND Power reference green
U1 Signal white
Connecting active probes with 0 to 10 V output
For information on the maximum number of probes that can be
connected see the table at the beginning of this paragraph. For details
on the operating range see the data sheets supplied with the probes.
G
G0
U1
U2
U3
GND
+VDC
+Vterm
GND
+5 VREF
U4
GND
U5
GND
VG
VG0
Y1
Y2
Y3
Y4
ID1
ID2
ID3
ID4
J1 J24 J2 J3 J4
F ie ld Bus c ar d B MS ca r d
U1
U2
U3
GND
+VDC
M
out T
+ ( )G
out H
Fig. 5.h
Key
Controller terminals Active probes with 0 to 10 V output
GND Reference
+VDC Power
U1 Signal 1
U2 Signal 2
Max. number of connectable digital inputs
The controller allows the universal inputs/outputs to be configured as
non-optically isolated, voltage-free digital inputs. In any case, the inputs
must be connected to a voltage-free contact.
Maximum number of dig. inputs connectable
to universal inputs/outputs
Type of signal
c.pCO
mini Small Medium/ Built-in
driver/ Extralarge Large
Digital
inputs
(not opto-
isolated)
- volt-free
contacts 10 5 8 10
- fast
inputs max 2 max 2
4
(max 2 on U1...U5,
max 2 on U6..U8)
6
(max 2 on U1...U5,
max 2 on U6...U8,
2 on U9...U10)
Tab. 5.c
Important: the maximum current allowed on the digital input is 10
mA. Therefore the rating of the external contact must be at least 10 mA.
Connecting ON/OFF inputs
There is no particular restriction on the maximum number of inputs that
can be connected. For details on the operating range see the Technical
Specifications table (see chap. 12).
G
G0
U1
U2
U3
GND
+VDC
+Vt erm
GND
+5 VREF
U4
GND
U5
GND
VG
VG0
Y1
Y2
Y3
Y4
ID1
ID2
ID3
ID4
ID5
ID6
ID7
J1 J24 J2 J3 J4 J5
FieldB u s ca r d B M S ca r d
U4
U5
GND
GND
Fig. 5.i
Key
Controller terminals Description
U4 Digital input 1
GND
U5 Digital input 2
GND
Connecting fast digital inputs
Important: the wires connecting the fast digital inputs/counters
must be shielded to avoid causing electromagnetic interference with the
probe cables.
G
G0
U1
u2
U3
GND
+VDC
+Vte rm
GND
+5 VREF
U4
GND
U5
GND
J1 J24 J2 J3
Field B us c ard
U4
GND
U5
GND
J3
E lxterna
imp seul
generator
Fig. 5.j
31
ENG
c.pCO sistema +0300057EN rel. 1.4 - 25.10.2020
The fast digital input can be used as a frequency meter. The count is
performed on the rising edge of the pulse. The pulse generator device
will have one digital output with transistor optocoupler, which will be
connected to the input as shown in the figure. For details on the input
signal see the Technical Specifications table (see chap. 12).
Note: the application program shows the frequency values using
specific variables. If the inputs are configured as counters, the counter is
reset by the application program.
Example:
t
t
inp tu
count
Fig. 5.k
Note: in the case of fans with current output and high series
resistance, the reading of the pulses may depend on the current. The
current value can be configured in the c.design I/O Editor.
Connecting non-optically-isolated analogue outputs
There is no particular restriction on the number of outputs that can
be connected. For details on the output signal see the Technical
Specifications table (see chap. 12).
Example: analogue/PWM output connection diagram.
U1
U2
U3
GND
+VDC
+Vterm
GND
+5 VREF
U4
GND
U5
GND
VG
VG0
Y1
Y2
Y3
Y4
ID1
J24 J2 J3 J4
ID1
Vo tu
Vo tu
Fig. 5.l
Key
Controller terminals Description
U1 Analogue output 1
GND
U2 Analogue output 2
GND
U3 Analogue output 3
GND
Note: the analogue outputs cannot be connected in parallel.
5.3 Digital inputs
The controller features digital inputs for connecting safety devices, alarms,
device status indicators and remote switches. See the table of technical
specifications for the maximum cable length cables (see chap. 12).
c.pCOmini
The digital inputs are not optically-isolated and have voltage-free
contacts. The following figure shows how to connect the digital inputs:
U1
U2
U3
GND
U4
U5
U6
GND
U7
U8
U9
U10
GND
J1
G
G0
Vbat
+5VREF
GND
+V DC
J9
Y1
GND
ID2
ID1
Y2
GND
J8
J7
J2
Fig. 5.m
c.pCO Small...Extralarge
These inputs are all optically isolated from the other terminals. They can
work at 24 Vac (+10/-15%) or 28 to 36 Vdc (-20/+10%) (indicated as ID*),
and some at 230 Vac (indicated as IDH*), see as reference figure below.
Note:
if the control voltage is drawn in parallel with a coil, install a dedicated
RC filter in parallel with the coil (typical ratings are 100 Ω, 0.5 μF, 630 V);
if the digital inputs are connected to safety systems (alarms), the
presence of voltage across the contact should be taken as the normal
operating condition, while no voltage represents an alarm situation.
This will ensure that any interruption (or disconnection) of the input
will also be signalled;
do not connect the neutral in place of an open digital input;
always interrupt the phase.
Important:
to avoid electromagnetic interference, keep the probe and digital
input cables separate from the power cables as much as possible (at
least 3 cm). Never run power cables and probe signal cables in the
same conduits (including the ones in the electrical panels.
24 Vac digital inputs (c.pCO Small... Extralarge only)
Digital inputs ID... can be controlled at 24 Vac.
Note:
the digital inputs are only functionally isolated from the rest of the
controller;
to keep the digital inputs optically isolated a separate power supply is
needed for each input;
the digital inputs can be powered at a different voltage from the rest
of the controller.
Cable cross-section
For remote connections to the digital inputs (length <50 m), use cables
with a cross-section = 0.25 (mm2)
Important: If the controller is installed in an industrial environment
(standard EN 61000-6-2) the connections must be less than 30 m long. Do
not exceed this length to avoid measurement errors.
32
ENG
c.pCO sistema +0300057EN rel. 1.4 - 25.10.2020
Example of connection diagram (LARGE model):
G
G0
U1
U2
U3
GND
+VDC
+Vterm
GND
+5 VREF
U4
GND
U5
GND
VG
V 0G
Y1
Y2
Y3
Y4
ID1
ID2
ID3
ID4
ID5
ID6
ID7
ID8
I 1DC
U6
U7
U8
GND
ID9
ID10
ID11
ID12
IDC9
ID13H
ID13
I 1DC 3
ID14
ID14H
J1 J24 J2 J3 J4 J J5 7 J8
J20
J6
J19
ID15H
ID15
IDC15
ID16
ID16H
Y5
Y6
ID17
ID18
IDC17
U9
GND
U10
GND
F i e l d B u s c a r d B M S c a r d
G
G0
24 Vac
I 1D
ID2
ID3
I 4D
ID5
I 6D
ID7
ID8
I 1DC
ID9
I 1D 0
I 11D
I 1D 2
IDC9
I 1 HD 3
I 1D 3
I 1DC 3
I 14D
I 14HD
Fig. 5.n
G
G0
U1
U2
U3
GND
+VDC
+Vterm
GND
+5 VREF
U4
GND
U5
GND
VG
VG0
Y1
Y2
Y3
Y4
ID1
ID2
ID3
ID4
ID5
ID6
ID7
ID8
IDC1
U6
U7
U8
GND
ID9
ID10
ID11
ID12
IDC9
ID13H
ID13
IDC13
ID14
ID14H
J1 J24 J2 J3 J4 J5 J7
J8
J20
J6
J19
ID15H
ID15
IDC15
ID16
ID16H
Y5
Y6
ID17
ID18
IDC17
U9
GND
U10
GND
F i e ldB u s c a rd BM S c a r d
230 Vac
L
N
-
+
24 Vdc
Fig. 5.o
24 Vdc digital inputs
The ID... digital inputs can be controlled at 24 Vdc.
Example of connection diagram (LARGE model):
G
G0
U1
U2
U3
GND
+VDC
+Vterm
GND
+5 VREF
U4
GND
U5
GND
VG
VG0
Y1
Y2
Y3
Y4
ID1
ID2
ID3
ID4
ID5
ID6
ID7
ID8
IDC1
U6
U7
U8
GND
ID9
ID10
ID11
ID12
IDC9
ID13H
ID13
IDC13
ID14
ID14H
J1 J24 J2 J3 J4 J5 J7
J8
J20
J6
J19
ID15H
ID15
IDC15
ID16
ID16H
Y5
Y6
ID17
ID18
IDC17
U9
GND
U10
GND
Fi e l d B us c a rd BM S c a r d
input: 24 V 50...60 Hz / 28...36 V
max. power: 45 VA/20 W
-
+
24 Vdc
I 1D
ID2
ID3
I 4D
ID5
I 6D
ID7
ID8
I 1DC
ID9
ID10
ID11
ID12
IDC9
ID13H
ID13
IDC13
ID14
ID14H
Fig. 5.p
G
G0
U1
U2
U3
GND
+VDC
+Vterm
GND
+5 VREF
U4
GND
U5
GND
VG
VG0
Y1
Y2
Y3
Y4
ID1
ID2
ID3
ID4
ID5
ID6
ID7
ID8
IDC1
U6
U7
U8
GND
ID9
ID10
ID11
ID12
IDC9
ID13H
ID13
IDC13
ID14
J1 J24 J2 J3 J4 J5 J7 J8
J20
J6
J19
ID15H
ID15
IDC15
ID16
ID16H
Y5
Y6
ID17
ID18
IDC17
U9
GND
U10
GND
Fi e l d B u s ca rd BMS c a r d
-
+
24 Vdc
Fig. 5.q
33
ENG
c.pCO sistema +0300057EN rel. 1.4 - 25.10.2020
230 Vac digital inputs (c.pCO Medium...Extralarge only)
Medium and Extralarge models feature one group of 230 Vac inputs
(terminal J8), while Large models have two groups (on terminals J8 and
J19). Each group consists of two digital inputs that can be powered at 230
Vac, indicated as IDH*, and two inputs that can be powered at 24 Vac/Vdc,
indicated as ID*. The two groups of 230 Vac inputs have double insulation
between each other and between them and the controller. The digital
inputs connected may be the 24 Vac/dc inputs from one group and the
230 Vac inputs from the other. The two inputs of each group have the
same common pole. Functional insulation is provided. In each group, the
digital inputs must be powered at the same voltage (24 Vac, 28 to 36
Vdc or 230 Vac) in order to avoid dangerous short-circuits and/or the
risk of powering lower-voltage circuits at 230 Vac
Note:
the range of uncertainty of the switching threshold is from 43 to 90 Vac;
the voltage must be 230 Vac (+10/-15%), 50/60 Hz.
Example 1: connection diagram with 230 Vac inputs.
G
G0
U1
U2
U3
GND
+VDC
+Vterm
GND
+5 VREF
U4
GND
U5
GND
VG
VG0
Y1
Y2
Y3
Y4
ID1
ID2
ID3
ID4
ID5
ID6
ID7
ID8
IDC1
U6
U7
U8
GND
ID9
ID10
ID11
ID12
IDC9
ID13H
ID13
IDC13
ID14
ID14H
J1 J24 J2 J3 J4 J5 J7
J8
J20
J6
J19
ID15H
ID15
IDC15
ID16
ID16H
Y5
Y6
ID17
ID18
IDC17
U9
GND
U10
GND
Fi e l d B u s c a r d B M S c a r d
230 Vac
L
N
Fig. 5.r
Example 2: connection diagram with digital inputs at dierent voltages.
G
G0
U1
U2
U3
GND
+VDC
+Vterm
GND
+5 VREF
U4
GND
U5
GND
VG
VG0
Y1
Y2
Y3
Y4
ID1
ID2
ID3
ID4
ID5
ID6
ID7
ID8
IDC1
U6
U7
U8
GND
ID9
ID10
ID11
ID12
IDC9
ID13H
ID13
IDC13
ID14
ID14H
J1 J24 J2 J3 J4 J5 J7
J8
J20
J6
J19
ID15H
ID15
IDC15
ID16
ID16H
Y5
Y6
ID17
ID18
IDC17
U9
GND
U10
GND
F i e l d B u s c a r d B M S c a r d
230 Vac
L
N
-
+
24 Vdc
Fig. 5.s
5.4 Analogue outputs
c.pCOmini: analogue outputs without optical isolation
The controller features 0 to 10 Vdc and PWM analogue outputs without
optical isolation, powered directly by the controller. See the table of the
technical specifications (output current, output impedance, etc., Chap. 12).
Example connection diagram (c.pCOmini model):
U1
U2
U3
GND
U4
U5
U6
GND
U7
U9
U10
GND
J1 J2
G
G0
Vbat
+5VREF
GND
+V DC
J9
Y1
GND
ID2
ID1
Y2
GND
J8
J7
24 Vac / 28...36 Vdc
0 V
Vout
Vout
Fig. 5.t
34
ENG
c.pCO sistema +0300057EN rel. 1.4 - 25.10.2020
c.pCO Small...Extralarge: 0 to 10 V analogue outputs
On terminals VG and VG0 the controller provides optically-isolated 0 to 10
V analogue outputs, to be powered externally at the same voltage as the
controller, i.e. 24 Vac or 28 to 36 Vdc. The connection diagram is shown
in the figure below. The 0 V supply voltage is also the voltage reference
of the outputs. See the Technical Specifications table for details on the
output current, output impedance, etc. (see chap. 12).
Note:
the analogue output can be connected to the CONVONOFF0 module
to convert the 0 to 10 V output into an ON/OFF relay output;
a 0 to 10 Vdc analogue output can be connected in parallel to other
outputs of the same type, or alternatively to an external voltage
source. The higher voltage will be considered. Correct operation is not
guaranteed if actuators with voltage inputs are connected;
if optical isolation is not required, the VG-VG0 analogue outputs can be
powered at the same voltage on G-G0: connect G0 to VG0 and G to VG.
Example connection diagram (LARGE model):
U1
U2
U3
GND
+VDC
U4
GND
U5
GND
VG
VG0
Y1
Y2
Y3
Y4
ID1
ID2
ID3
ID4
ID5
ID6
ID7
ID8
IDC1
U6
U7
U8
GND
ID9
ID10
ID11
ID12
I DC9
ID13H
ID13
IDC13
ID14
ID14H
J2 J3 J4 J5 J7 J8
J20
J6
J
19
ID15H
ID15
IDC15
ID16
ID16H
Y5
Y6
ID17
ID18
IDC17
U9
GND
U10
GND
Fi e l dB u s ca r d BM S ca r d
24 Vac / 28...3 Vdc 6
0 V
ID1
ID2
ID3
ID4
ID5
ID6
ID7
ID8
IDC1
ID9
ID10
ID11
ID12
IDC9
ID13H
ID13
IDC13
ID14
ID14H
Vo tu
Vo tu
Vo tu
Vo tu
Vo tu
Vo tu
Fig. 5.u
Maximum number of optically-isolated analogue outputs (ref. VG0)
c.pCO model Small/Medium/Extralarge Large
Outputs Y1, Y2, Y3, Y4 Y1, Y2, Y3, Y4, Y5, Y6
5.5 Connecting the Ultracap module
The Ultracap module can be connected to power the controllers in the event
of blackouts:
1. c.pCOmini controller: the module guarantees temporary power to
the controller and driver for enough time to close the electronic
valve (40s with forced closing of the valve, 60s without forced closing
of the valve). NB: with Vdc power supply, forced closing of the
electronic expansion valve is not managed in the event of blackouts.
25A, T
24 Vac 230 Vac
4 0 VA
U1
U2
U3
GND
U4
U5
U6
GND
U7
U8
U9
U10
GND
J1 J2
G
G0
Vbat
G/G0: 24 V~ 50...60 Hz / 28...36 V 30 VA/12W
J3 Disp.
+Vterm
J4 FBus J5 CAN
L H
Ultracap echno T logy
G
G0
Vbat
Fig. 5.v
35
ENG
c.pCO sistema +0300057EN rel. 1.4 - 25.10.2020
2. c.pCO controller with built-in driver: the module guarantees
temporary power to the driver for enough time to close the
electronic valves.
80 VA
2.5 AT
C7
NO7
C7
NO8
C8
NC8
NO13
C13
NC13
C9
NO9
NO10
NO11
C9
ID6
ID7
ID8
IDC1
B6
B7
B8
GND
ID9
ID10
ID11
ID12
IDC9
ID13H
ID13
IDC13
ID14
ID14H
J7 J8
J29
J14
J28
J17 J18J15
J6
J30
J27
VBAT
G0
G
GND
VREF
S1
S2
S3
S4
DI1
DI2
dri erv
G
G0
VBAT
Ultracap e chno T logy
CAREL E
XV
v lv a e A
1 43 2 1 43 2
CAREL EXV
v lv a e B
G
G0
NO12
C12
NC12
J16
Fig. 5.w
5.6 Connecting the electronic valve
c.pCOmini: unipolar electronic valve
The controller incorporates the driver for connection of an unipolar
electronic expansion valve.
Note: to manage the valve, the control algorithm requires 2
probes (1 pressure probe and 1 temperature probe);
Connection example using ratiometric probes (pressure) and NTC
probes (temperature).
U1
U2
U3
GND
U4
U5
U6
GND
U7
U8
U9
U10
GND
J1 J2
G
G0
Vbat
+5VREF
GND
+V dc
J9
G/G0: 24 V~ 50...60 Hz / 28...36 V 30 VA/12W
Y1
GND
ID2
ID1
Y2
GND
J8
J7
CAREL E2V* *, E3V
Unipolar valve
NTC
Ratiometric pressure
transducer
Fig. 5.x
c.pCO (Medium with built-in driver): bipolar electronic valve
The controller with a built-in driver can be used to control one or two
electronic expansion valves with two-pole motor.
Example connection diagram (the colour of the wires refers to the
standard Carel valve cable P/N E2VCABS*00):
A B C D
C7
NO8
C8
NC8
J15
J27
1
3
2
4
J28
1
3
2
4
driver
VBAT
G0
G
J30
GND
VREF
S1
S2
S3
S4
DI1
DI2
J29
shield shield
giallo/yellow
bianco/white
verde/green
marrone/brown
NTC driver A
ratiometric pressure
transducer driver A
NTC driver B
ratiometric pressure
transducer driver B
digital input to start the
regulation of driver A
digital input to start the
regulation of driver B
CAREL Ex
V valve A CAREL ExV valve B
Fig. 5.y
Note:
connect the valve cable shield to the spade connector and then to the
earth;
for information on the compatibility of valves and refrigerants, see the
Technical Specifications table (see chap. 12) and the EVD Evolution driver
manual.
On the controller with built-in valve driver it is possible to apply the
Ultracap module (accessory P/N PCOS00UC20) . The module is made
with special capacitors called ultracapacitors that close the electronic
valve in case of power failures. The module only powers the driver and
not the controller.
Important: the c.pCO with built-in driver and PCOS00UC20 module
(or EVD0000UC0 external Ultracap module, or EVBAT00400 battery) must
be powered at 24 Vac so that emergency valve closing is ensured in case
of power failures. If the controller is powered with DC voltage it will not
close the valve in case of power failures.
Note:
the built-in driver replicates all the hardware and logic functions of
the “EVD Evolution stand-alone driver in case of 1 valve and of the
“EVD Evolution TWIN” driver in case of 2 valves. In other words, it
independently controls one or two electronic expansion valves with
two-pole stepper motors. The only difference with EVD Evolution is
that there are no output relays. For details on the valve control logic,
set-up and installation, see the EVD Evolution manual (+0300005EN for
single driver, +0300006EN for double driver);
as with EVD Evolution, the built-in driver on the c.pCO controller
is available in the CAREL and the “Universal” versions. “Universal”
models are used to control both CAREL electronic expansion valves,
as well as valves produced by other manufacturers (see the Technical
Specifications table, chap. 12), while CAREL models only control CAREL
valves.
37
ENG
c.pCO sistema +0300057EN rel. 1.4 - 25.10.2020
Remote connection of digital outputs
The table below shows the cable sizes required according to the current.
Cross-section (mm2)/AWG Current (A)
0,5/20 2
1,5/15 6
2,5/14 8
Note: when dierent relay outputs must be operated consecutively
at very close intervals (e.g. star-delta motor starter) in the order of
hundreds of ms, use relays belonging to the same group, according to
the following table.
c.pCOmini - c.pCOe
relay groups for consecutive commands (~ 100 ms)
123
Relay 1, 2 3,4,5 6
c.pCO Small...Extralarge
relay groups for consecutive commands (~ 100 ms)
1 2 3 4 - c.pCO
Large
4 -
c.pCO ExtraLarge 5
Relay 1, 2, 3, 45, 6,
7, 8
9, 10, 11,
12, 13
14, 15, 16,
17, 18
14, 15, 16, 17, 18,
19, 20, 21
22, 23, 24, 25,
26, 27, 28, 29
Important: using relays that belong to dierent groups can cause
delays in switching.
5.8 Solid state relay (SSR) digital outputs
c.pCO controllers are also available in versions with solid-state relays (SSR)
for controlling devices that require an high number of switching cycles that
would not be supported by electromechanical relays. These outputs are
dedicated to resistive loads powered at 224 Vac SELV or 28 to 36 Vdc SELV
with max. load current up to 1 A or 230 Vac with max. load current up to
70 mA.
Example 1: connection diagram for resistive load.
NO1
NO2
NO3
C1
C4
NO4
NO5
NO6
C4
C7
NO7
C7
NO8
C8
NC8
24 Vac/Vdc
Fig. 5.ac
Example 2: connection diagram for inductive or resistive loads, with
max. load current < 1 A.
NO5
NO6
C4
C7
NO7
C7
NO8
C8
NC8
24 Vac/Vdc( )*
SSR S RNO/ E TE
EXTE L RNA SSR carico/load
inp tu
Fig. 5.ad
(*) dedicated power supply or same power supply as controller: not in
common with the power supply for other external loads (e.g. contactors,
coils).
Important: in applications with SSR outputs:
the controller should only power resistive loads with load current less
than maximum declared;
use an additional external SSR to power inductive loads;
for AC power supply to resistive loads or external SSRs, use the same
power supply as the controller (connected to terminals G/G0), which
must be dedicated and not in common with the power supply to other
devices in the electrical panel (contactors, coils, etc.)
Note: the SSR load is powered at 24 Vac SELV, 28 to 36 Vdc SELV or
230 Vac; consequently all the other terminals in the group must be
powered at the same voltage due to the absence of reinforced insulation
within the group.
38
MINI
digital input 1
digital input 2
out H
M
NTC
NTC
+ (G)
probe 7-8
probe 4 Carel NTC
probe 5 Carel NTC
probe 6 voltage-free/digital input
probe 9 voltage-free/digital input
probe 10 voltage-free/digital input
probe 1 (0/5V)
230/24 Vac
L
N
2,5 A T
analog output 1 (0...10 Vdc)
analog output 2 (0...10 Vdc)
M
OUT
+V
probe 2 (4/20 mA)
probe 3 (0/1 Vdc or 4/20 mA))
digital output 1
digital output 2
digital output 3
digital output 4
digital output 5
digital output 6
ENG
c.pCO sistema +0300057EN rel. 1.4 - 25.10.2020
5.9 General connection diagram c.pCOmini
Fig. 5.ae
39
SMALL MEDI MU LARGE
230/24 Vac
M
OUT
+V
analog output 1 (0...10 Vdc)
analog output 2 (0...10 Vdc)
analog output 3 (0...10 Vdc)
analog output 4 (0...10 Vdc)
analog output 5 (0...10 Vdc)
digital output 1
digital output 2
digital output 3
digital output 4
digital input 1
digital input 2
digital input 3
digital input 4
digital input 5
digital input 6
digital input 7
digital input 8
digital input 15
digital input 16
digital input 17
digital input 18
digital output 5
digital output 6
digital output 7
digital output 8
digital output 14
digital output 15
digital output 16
digital output 17
digital output 18
probe 9 CAREL NTC
probe 10
voltage-free
digital input
analog output 6 (0...10 Vdc)
out H
M
NTC
NTC
+ (G)
digital input 9
CP
digital input 10
digital input 11
digital input 12
digital input 13
digital input 14
digital output 9
digital output 10
digital output 11
digital output 12
digital output 13
probe 8 CAREL NTC
probe 6 - 7
50VA
2.5 AT
C1
NO1
NO2
NO3
C1
C4
NO4
NO5
NO6
C4
C7
NO7
C7
NO8
C8
NC8
G
G0
U1
U2
U3
GND
+VDC
+Vterm
GND
+5 VREF
U4
GND
U5
GND
VG
VG0
Y1
Y2
Y3
Y4
ID1
ID2
ID3
ID4
ID5
ID6
ID7
ID8
IDC1
J1 J24 J2 J3 J4 J5
J14
J10
J13J12 J15
Field B u s card BMS ca r d
J11 pLAN
J25 BMS2 J26 FBus2
4 3 2 1
NO12
C12
NC12
NO13
C13
NC13
C9
NO9
NO10
NO11
C9
IDC1
U6
U7
U8
GND
ID9
ID10
ID11
ID12
IDC9
ID13H
ID13
IDC13
ID14
ID14H
J7 J8
J16 J17 J18
J6
J20
J21 J22
J19
NO14
C14
NC14
NO15
C15
NC15
C16
NO16
NO17
NO18
C16
ID15H
ID15
IDC15
ID16
ID16H
Y5
Y6
ID17
ID18
IDC17
U9
GND
U10
GND
J23 FBus2
probe 1 (0/5 V)
probe 2 (4/20 mA)
probe 3 (0/1 Vdc or 4/20 mA)
probe 4 Carel NTC
probe 5 PT1000
XXXXXXXXXXXX
N
L
ENG
c.pCO sistema +0300057EN rel. 1.4 - 25.10.2020
5.10 General connection diagram c.pCO
Fig. 5.af
40
ENG
c.pCO sistema +0300057EN rel. 1.4 - 25.10.2020
6. START-UP
6.1 Switching on
When the controller is switched on, it runs a test on the secondary display,
lighting up the segments one by one.
6.2 Private and shared terminal
All c.pCO controllers can be connected to each other in a local area
network (pLAN, see Figure 6.a) in order to share one or more terminals.
Shared terminals can show the variables (temperature, humidity, pressure,
I/O, alarms) from just one controller at a time. The terminal does not need
to be connected to the controller during normal operation, but can be
used just for the initial programming of the main parameters. If one or
more terminals are disconnected or malfunctioning, the application
program continues to work correctly on each controller. Generally, the
application program can monitor the status of the network and intervene
as necessary to ensure continuity of the control functions. The gure
below shows a possible pLAN network connection diagram.
p D /p DG E G 1
p N 85LA ( 4RS )
c.pCO DD: A R=1
C1
NO1
NO2
NO3
C1
C4
NO4
NO5
NO6
C4
C7
NO7
C7
NO8
C8
NC8
NO12
C12
NC12
NO13
C13
NC13
C9
NO9
NO10
NO11
C9
G
G0
U1
U2
U3
GND
+VDC
+Vterm
GND
+5 VREF
U4
GND
U5
GND
VG
VG0
Y1
Y2
Y3
Y4
ID1
ID2
ID3
ID4
ID5
ID6
ID7
ID8
IDC1
U6
U7
U8
GND
ID9
ID10
ID11
ID12
IDC9
ID13H
ID13
IDC13
ID14
ID14H
J1 J24 J2 J3 J4 J5 J7
J8
J20
J21
J14
J10
J13J 12
J22
J16 J17 J18J15
J6
J19
NO14
C14
NC14
NO15
C15
NC15
C16
NO16
NO17
NO18
C16
ID15H
ID15
IDC15
ID16
ID16H
Y5
Y6
ID17
ID18
IDC17
U9
GND
U10
GND
Fi el dBu s car d BM S c ar d
J23 FBus 2
input:24 V 50...60 Hz /28...36 V
max.power: 45 W VA/20
J11 pLAN J31
CANL
CANH
GND
J25 BM S2 J26 FBus 2
OFF
4 3 2 1
ON
c.pCO DD: A R 2=
C1
NO1
NO2
NO3
C1
C4
NO4
NO5
NO6
C4
C7
NO7
C7
NO8
C8
NC8
NO12
C12
NC12
NO13
C13
NC13
C9
NO9
NO10
NO11
C9
G
G0
U1
U2
U3
GND
+VDC
+Vterm
GND
+5 VREF
U4
GND
U5
GND
VG
VG0
Y1
Y2
Y3
Y4
ID1
ID2
ID3
ID4
ID5
ID6
ID7
ID8
IDC1
U6
U7
U8
GND
ID9
ID10
ID11
ID12
IDC9
ID13H
ID13
IDC13
ID14
ID14H
J1 J24 J2 J3 J4 J 5 J7
J8
J20
J21
J14
J10
J13J12
J22
J16 J17 J18J15
J6
J19
NO14
C14
NC14
NO15
C15
NC15
C16
NO16
NO17
NO18
C16
ID15H
ID15
IDC15
ID16
ID16H
Y5
Y6
ID17
ID18
IDC17
U9
GND
U10
GND
Fi el dBu s car d BM S c ar d
J23 FBus 2
input:24 V 50...60 Hz /28...36 V
max. power:45VA/20 W
J11 pLAN J31
CANL
CANH
GND
J25 BM S2 J26 FBus2
OFF
4 3 2 1
ON
Fig. 6.a
All the terminals and controllers in the network must communicate at the
same speed. The speed is adapted automatically.
A maximum of 32 units can be connected, including:
c.pCO controllers, which run the control program;
terminals.
Every device belonging to a pLAN network is identied by a unique
address, i.e. a number from 1 to 32. The number 32 can be assigned only to
a terminal. Programs for dierent applications (e.g. chillers, air-conditioners,
compressor racks, etc.) cannot be automatically integrated into a local
network they must be congured according to the system architecture
using the CAREL development tool.
Each controller connected to the network can simultaneously manage
up to 3 terminals in the pLAN network (semi-graphic terminals such as
pGDs or touch screens such as pGDT / pGDx). The values are displayed on
the terminals at the same time and not independently, as if the keypads
and the displays were connected in parallel. Because of that, the controller
cannot manage dierent kinds of terminals at the same time.
Each terminal associated with a certain controller is dened as:
- private (“Pr”) if it displays only the output of that controller;
- shared (“Sh”) if either automatically or from the keypad it can be switched
between various controllers.
Each c.pCO constantly updates the displays on the private terminals, while
the shared terminals (if present) are updated only by the c.pCO that is
controlling the terminal at that time.
The gure below illustrates the logic of the relationships:
C1
NO1
NO2
NO3
C1
C4
NO4
NO5
NO6
C4
C7
NO7
C7
NO8
C8
NC8
NO12
C12
NC12
NO13
C13
NC13
C9
NO9
NO10
NO11
C9
G
G0
U1
U2
U3
GND
+VDC
+Vterm
GND
+ 5 VREF
U4
GND
U5
GND
VG
VG0
Y1
Y2
Y3
Y4
ID1
ID2
ID3
I 4D
ID5
I 6D
ID7
ID8
IDC1
U6
U7
U8
GND
ID9
ID10
ID11
ID12
IDC9
I HD13
ID13
IDC13
I 4D1
ID14H
J J 4 J J1 2 2 3 J4 J J5 7
J8
J20
J21
J 41
J10
J13J12
J22
J 6 J1 17 J18J15
J6
J19
NO14
C14
NC14
NO15
C 51
NC15
C16
NO16
NO17
NO18
C16
I HD 51
ID 51
IDC15
I 6D1
ID16H
Y5
Y6
ID 71
ID 81
IDC17
U9
GND
U10
GND
F u c cie l dB s a rd B MS ar d
J F23 Bus2
i 2 0 0np tu : 4 V 5 ...6 Hz /2 38... 6 V
max. wpo er: 45 V / A20 W
J L11 p AN
J25
BMS2 J 62 F uB s2
4 3 2 1
C1
NO1
NO2
NO3
C1
C4
NO4
NO5
NO6
C4
C7
NO7
C7
NO8
C8
NC8
NO12
C12
NC12
NO13
C13
NC13
C9
NO9
NO10
NO11
C9
G
G0
U1
U2
U3
GND
+VDC
+Vterm
GND
+ 5 VREF
U4
GND
U5
GND
VG
VG0
Y1
Y2
Y3
Y4
ID1
ID2
ID3
I 4D
ID5
I 6D
ID7
ID8
IDC1
U6
U7
U8
GND
ID9
ID10
ID11
ID12
IDC9
I HD13
ID13
IDC13
I 4D1
ID14H
J J 4 J J1 2 2 3 J4 J J5 7
J8
J20
J21
J 41
J10
J13J12
J22
J 61 J17 J18J15
J6
J19
NO14
C14
NC14
NO15
C 51
NC15
C16
NO16
NO17
NO18
C16
I HD 51
ID 51
IDC15
I 6D1
ID16H
Y5
Y6
ID 71
ID 81
IDC17
U9
GND
U10
GND
F u c ciel d B s a rd BM S a rd
J F23 Bus2
i 2 0 0np tu : 4 V 5 ...6 Hz / 2 38... 6 V
max. power: 45 V / A20 W
J L11 p AN
J25
BMS2 J 62 F uB s2
4 3 2 1
C1
NO1
NO2
NO3
C1
C4
NO4
NO5
NO6
C4
C7
NO7
C7
NO8
C8
NC8
NO12
C12
NC12
NO13
C13
NC13
C9
NO9
NO10
NO11
C9
G
G0
U1
U2
U3
GND
+VDC
+Vterm
GND
+ 5 VREF
U4
GND
U5
GND
VG
VG0
Y1
Y2
Y3
Y4
ID1
ID2
ID3
I 4D
ID5
I 6D
ID7
ID8
IDC1
U6
U7
U8
GND
ID9
ID10
ID11
ID12
IDC9
I HD13
ID13
IDC13
I 4D1
ID14H
J J 4 J J1 2 2 3 J4 J J5 7
J8
J20
J21
J 41
J10
J13J12
J22
J 61 J17 J18J15
J6
J19
NO14
C14
NC14
NO15
C 51
NC15
C16
NO16
NO17
NO18
C16
I HD 51
ID 51
IDC15
I 6D1
ID16H
Y5
Y6
ID 71
ID 81
IDC17
U9
GND
U10
GND
F u c cie l dB s a rd B MS ar d
J F23 B s2u
i 2 0 0np tu : 4 V 5 ...6 Hz / 2 38... 6 V
max. w po er: 45V /A20 W
J L11 p AN
J25
BMS2 J 62 F uB s2
4 3 2 1
c 4.pCO:
c.pCO: 1 p D tG E P v ri a e
p D tG E P v ri a e p D tG E P v ri a e
p D tG E P v ri a e
p D /p D hG E G 1 S ared
1
34
2
c.pCO: 2
C1
NO1
NO2
NO3
C1
C4
NO4
NO5
NO6
C4
C7
NO7
C7
NO8
C8
NC8
NO12
C12
NC12
NO13
C13
NC13
C9
NO9
NO10
NO11
C9
G
G0
U1
U2
U3
GND
+VDC
+Vterm
GND
+ 5 VREF
U4
GND
U5
GND
VG
VG0
Y1
Y2
Y3
Y4
ID1
ID2
ID3
I 4D
ID5
I 6D
ID7
ID8
IDC1
U6
U7
U8
GND
ID9
ID10
ID11
ID12
IDC9
I HD13
ID13
IDC13
I 4D1
ID14H
J J 4 J J1 2 2 3 J4 J J5 7
J8
J20
J21
J 41
J10
J13J12
J22
J 6 J1 17 J18J15
J6
J19
NO14
C14
NC14
NO15
C 51
NC15
C16
NO16
NO17
NO18
C16
I HD 51
ID 51
IDC15
I 6D1
ID16H
Y5
Y6
ID 71
ID 81
IDC17
U9
GND
U10
GND
F u c cie l dB s a rd B MS ar d
J F23 B s2u
i 2 0 0nput: 4 V 5 ...6 Hz / 2 38... 6 V
max. pow er: 45 V /A 20 W
J L11 p AN
J25
BMS2 J 62 F uB s2
4 3 2 1
c.pCO 5:
Fig. 6.b
In this example, the shared terminal is associated with 4 controllers, but
at this instant only controller 1 can display data and receive commands
from the keypad. Switching between controllers occurs:
1. using a command in the system menu;
2. in sequence (1->2->3->4->1...) by pressing a button dened by the
application program; however it can also be done automatically
when requested by the program. For example, a c.pCO may request
control of the shared terminal to display alarms or, vice-versa,
relinquish control to the next c.pCO after a set time (cyclical rotation).
Data on the number and type of terminals is determined during initial
network conguration and saved in the permanent memory of each
c.pCO controller. Details of the conguration procedure are described
below. See the “Installation chapter for information on the cables to use
for the electrical connections.
6.3 Setting the controller pLAN address
The controller pLAN address is factory-set as 1.
There are two ways to set a controller address:
1. using button A (see the gure below) located next to the 7-segment
display. This can be accessed using the tip of a screwdriver (ø<3 mm);
2. from the system menu (see Chapter 7).
Displaying the pLAN address
The pLAN address is displayed permanently on the pLAN address display.
NO1
C1/2
NO2
NO3
C3/4/5
NO4
J10 J11
ID1
J7
GND
U5
GND
VG
VG0
Y1
J3 J4
car d
Fig. 6.c
42
ENG
c.pCO sistema +0300057EN rel. 1.4 - 25.10.2020
Acquire/ release commands
These commands are used by a controller to acquire / release a terminal.
Procedure:
1. Press Alarm and ENTER together to enter the system menu. Select
“Settings”
INFORMATION
SETTINGS
APPLICATION
UPGRADE
LOGGER
DIAGNOSTICS
2. Select pLAN Settings
PASSWORD
USB SETTINGS
PLAN SETTINGS
CLOCK SETTINGS
TCP/IP SETTINGS
3. The following screen is shown, where the acquire/release
commands can be activated.
pLan pCO Addr: 1
Release Term: No
Acquire Term: No
Update config: No/Yes
Key
pLan pCO addr. Address of c.pCO controller currently connected to the
terminal
Release terminal Release command
Acquire terminal Acquire command
Update congu-
ration
Conrm update
Command virtualisation
Whenever a pGD terminal is connected to a c.pCO, the pGD terminal
displays the corresponding user interface. The command is sent from
the terminal, however it is the controller that executes the operation to
release or acquire the terminal.
Example 1
A: the release command on terminal 21 releases c.pCO 3 from terminal
21, and this is then assigned to c.pCO 1;
B: the release command on terminal 21 releases c.pCO 1 from terminal 21,
and this is then assigned to c.pCO 2.
drac SMBdrac suBdleiF
XXXXXXXXXXXX
drac SMBdrac suBdleiF
XXXXXXXXXXXX
drac SMBdrac suBdleiF
XXXXXXXXXXXX
c.pCO
c.pCO
c.pCO
pGD
pGD
pGD
1
2
3
21
22
23
drac SMBdrac suBdleiF
XXXXXXXXXXXX
drac SMBdrac suBdleiF
XXXXXXXXXXXX
drac SMBdrac suBdleiF
XXXXXXXXXXXX
c.pCO
c.pCO
c.pCO
pGD
pGD
pGD
1
2
3
21
22
23
Term 21:
Release term
A B
drac SMBdrac suBdleiF
XXXXXXXXXXXX
drac SMBdrac suBdleiF
XXXXXXXXXXXX
drac SMBdrac suBdleiF
XXXXXXXXXXXX
c.pCO
c.pCO
c.pCO
pGD
pGD
pGD
1
2
3
21
22
23
Term 21:
Release term
Example 2
A: the release command on terminal 22 releases c.pCO 3 from terminal
21, and this is then assigned to c.pCO 1;
B: the release command on terminal 22 releases c.pCO 3 from terminal 22,
and this is then assigned to c.pCO 1.
drac SMBdrac suBdleiF
XXXXXXXXXXXX
drac SMBdrac suBdleiF
XXXXXXXXXXXX
drac SMBdrac suBdleiF
XXXXXXXXXXXX
c.pCO
c.pCO
c.pCO
pGD
pGD
pGD
1
2
3
21
22
23
drac SMBdrac suBdleiF
XXXXXXXXXXXX
drac SMBdrac suBdleiF
XXXXXXXXXXXX
drac SMBdrac suBdleiF
XXXXXXXXXXXX
c.pCO
c.pCO
c.pCO
pGD
pGD
pGD
1
2
3
21
22
23
Term 22:
Release term
A B
drac SMBdrac suBdleiF
XXXXXXXXXXXX
drac SMBdrac suBdleiF
XXXXXXXXXXXX
drac SMBdrac suBdleiF
XXXXXXXXXXXX
c.pCO
c.pCO
c.pCO
pGD
pGD
pGD
1
2
3
21
22
23
Term 22:
Release term
Example 3
A: the acquire command on terminal 22 acquires c.pCO 1 on terminal 21,
and this is thus assigned to c.pCO 1;
B: the acquire command on terminal 22 has no eect, as c.pCO 1 has
already acquired all the terminals
drac SMBdrac suBdleiF
XXXXXXXXXXXX
drac SMBdrac suBdleiF
XXXXXXXXXXXX
drac SMBdrac suBdleiF
XXXXXXXXXXXX
c.pCO
c.pCO
c.pCO
pGD
pGD
pGD
1
2
3
21
22
23
drac SMBdrac suBdleiF
XXXXXXXXXXXX
drac SMBdrac suBdleiF
XXXXXXXXXXXX
drac SMBdrac suBdleiF
XXXXXXXXXXXX
c.pCO
c.pCO
c.pCO
pGD
pGD
pGD
1
2
3
21
22
23
Term 22:
Release term
A B
drac SMBdrac suBdleiF
XXXXXXXXXXXX
drac SMBdrac suBdleiF
XXXXXXXXXXXX
drac SMBdrac suBdleiF
XXXXXXXXXXXX
c.pCO
c.pCO
c.pCO
pGD
pGD
pGD
1
2
3
21
22
23
Term 22:
Release term
6.6 Uploading/updating the software
It is possible to load/update the application software of the c.pCO
controllers family with the following methods:
Update from computer by using c.factory (via USB or Ethernet
connection
Update via USB ash drive
Update with le transfer via FTP (see par. FTP commands)
Update via tERA cloud service
The c.factory software is part of the c.suite, but it can be also installed
individually, downloading it from http://ksa.carel.com under “Software &
Support”->“c.suite”.
Update from computer using c.factory
On all c.pCO family controllers, the application program can be uploaded
by using the c.factory software, with direct connection to the controller
via USB cable or Ethernet network. To upload the application program,
proceed as follows:
a) Update from computer using c.factory via Ethernet connection:
Congure the computer and the c.pCO controller so that they belong to
the same LAN (see paragraph 9.2).
1. Open c.factory and select the application program le compiled in
c.strategy tool (“.otr” le extension). The tool will list the congurations
dened in c.design. Select the conguration to be loaded on the
controller and click “next.
Fig. 6.f
44
ENG
c.pCO sistema +0300057EN rel. 1.4 - 25.10.2020
2. Select the les to be loaded onto the controller and click ”Export Ap1”. In
the application package it is possible to include also:
the Operating System, selecting the specic path;
the web pages for the c.pCO web server functionality (see Chapter 10).
Fig. 6.l
3. Click “Export” and save the le to a ash drive, under a directory called
“UPGRADE”.
4. Plug the ash drive into the Host USB port and enter the system
menu (see Chapter 7). On the screen, select UPGRADE and then the
application program to be loaded and conrm by pressing enter.
USB key
A
Fig. 6.m
INFORMATION
SETTINGS
APPLICATION
UPGRADE
LOGGER
DIAGNOSTICS
INFORMATION
SETTINGS
APPLICATION
UPGRADE
LOGGER
DIAGNOSTICS
Important:
Before updating the c.pCO controller via USB connection, check in
the system menu that the Host USB port is enabled (Settings --> USB
Settings --> Pen drive, see Chapter 7).
Only use ash drives with FAT le system.
Do not use both USB ports on the controller at the same time.
Do not use mass storage peripherals that have a current draw more
than 500 mA.
Update with le transfer via FTP
The c.pCO family controllers tted with Ethernet port include an FTP
server that provides access to the public partition of the le system.
Files and directories in this partition can be read, modied, created and
deleted. FTP can also be used to transfer an .ap1 le, for example to
update the image of the operating system or the application program.
This is done using an FTP client, for example “FileZilla.
To protect the contents of the public le system against unauthorised
access, dierent users can be created, assigning each a dierent access
prole, dedicated to each service and adapted to the individual directory
(see Chapter 9). To update via FTP:
1. Open an FTP client (e.g. FileZilla). Enter the IP address of the c.pCO
controller and the access credentials (default user “anonymous”, no
password).
2. Drag & drop the software update le from the directory on the
computer to the “UPGRADE” directory on the c.pCO controller.
Fig. 6.n
Nota: Please use following settings in Filezilla:
Edit->Settings->Connection-> set timeout in seconds = 0
Edit -> Settings -> Transfers -> set maximum simultaneous transfers to 1
3. Access the system menu on the c.pCO and select “UPGRADE” (see
Chapter 7).
INFORMATION
SETTINGS
APPLICATION
UPGRADE
LOGGER
DIAGNOSTICS
INFORMATION
SETTINGS
APPLICATION
UPGRADE
LOGGER
DIAGNOSTICS
Note: when having loaded the update le to the “UPGRADE”
directory via FTP, the update procedure can also be started using the
virtual terminal (see paragraph 10.3).
Update via tERA cloud service.
See paragraph 10.6.


Specyfikacje produktu

Marka: Carel
Kategoria: Niesklasyfikowane
Model: c.pCO

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Carel c.pCO, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje Niesklasyfikowane Carel

Carel

Carel Hecu Instrukcja

30 Grudnia 2025
Carel

Carel µChiller process Instrukcja

14 Października 2024
Carel

Carel Karta KNX Instrukcja

29 Września 2024
Carel

Carel iJF Instrukcja

17 Września 2024
Carel

Carel SmartCella Instrukcja

15 Września 2024
Carel

Carel Energy2 Instrukcja

14 Września 2024
Carel

Carel µC3 Instrukcja

13 Września 2024
Carel

Carel powersplit Instrukcja

13 Września 2024
Carel

Carel MPXone Instrukcja

5 Września 2024
Carel

Carel c.pCO Instrukcja

4 Września 2024

Instrukcje Niesklasyfikowane

Najnowsze instrukcje dla Niesklasyfikowane

SmallRig

SmallRig VB99 SE Instrukcja

29 Stycznia 2025
QSC

QSC TSC-8 Instrukcja

29 Stycznia 2025
XTRARM

XTRARM XTR-FS5130 Instrukcja

29 Stycznia 2025
Sunding

Sunding SD-581G Instrukcja

29 Stycznia 2025
XTRARM

XTRARM XTR-FS5070 Instrukcja

29 Stycznia 2025
XTRARM

XTRARM XTR-FS2010 Instrukcja

29 Stycznia 2025
OSEE

OSEE TX402 Instrukcja

29 Stycznia 2025