Instrukcja obsługi Cannondale IQ400

Cannondale komputer rowerowy IQ400

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Cannondale IQ400 (6 stron) w kategorii komputer rowerowy. Ta instrukcja była pomocna dla 3 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/6

THANK YOU FOR PURCHASING A CANNONDALE

Congratulations on your purchase of a Cannondale IQ Series computer.

Proper setup and operation will greatly enhance this product’s usefulness and your

enjoyment.

Please follow all Warnings and read all sections of this manual carefully and become fully

familiar with its operation before using it.

YOUR CANNONDALE RETAILER

Along with this manual, your key source of information and assistance is the shop where

you purchased this product. Your local Authorized Cannondale Retailer is your primary

contact to discuss service and adjustment to this product, instruction in its use, and any

warranty questions.

To nd an Authorized Cannondale Retailer closest to you, call 1800BIKEUSA. Or you can

use our dealer locator at our website www.cannondale.com.

IMPORTANT INFORMATION FOR ALL CANNONDALE CYCLING COMPUTERS

WARNINGS

WIRELESS COMPUTER MODELS (IQ200, IQ300, and IQ400) - People with medical/

implanted electronic equipment or devices such as heart pacemakers, EKG equipment,

etc. must not use wireless cycle computers due to possible risk of interference with the

medical devices.

EXERCISE - Adults with health problems (such as heart disease, diabetes or obesity) or

those at high risk, men over age 40 and women over age 50 or pregnant should talk

with their doctor before starting an exercise program.

INTENDED USE: For bicycle use only. Not for use on any motorized vehicle.

OPERATE COMPUTER ONLY WHEN NOT RIDING: Failure to pay attention to the road,

trail, trac or your surroundings could result in an accident, with risk of serious injury,

paralysis or death. You must focus on riding, not your computer. Learn computer opera-

tions, and do all possible computer operations when not riding. For any operations you

choose to perform while riding, choose a time and place where this distraction has less

risk.

MAKE SURE ALL COMPUTER PARTS ARE INSTALLED PROPERLY: The computer

must not interfere with the bicycle controls and your ability to use them. Mount the

computer according to the directions in this instruction manual. See your Authorized

Cannondale Retailer if you have any trouble installing or maintaining your computer.

CHECK FOR DAMAGE REGULARLY: Regularly check the position, alignment, and

condition of the spoke magnet, wireless sensor, cadence sensor, sensor and sensor wire

to make sure they are secure, aligned and in good condition. Make sure nothing is loose

and there are no worn or damaged parts.

BATTERIES: Use only battery size and type specied on the unit. Do not leave any

batteries in reach of children, and dispose of them correctly. If a battery is swallowed,

consult a doctor immediately.

NOT A TOY: Keep this computer and associated parts including the battery away from

children. Small parts could be swallowed.

YOU CAN BE SEVERELY INJURED, PARALYZED OR KILLED IN AN ACCIDENT IF YOU

IGNORE THESE WARNINGS.

NOTICE

■ This product is rain-proof only. Do not submerge or power wash.

■ Do not disassemble the unit.

■ Mount the computer according to the directions in this instruction manual.

■ Avoid direct impact to the computer unit.

■ Avoid using the computer unit in or near strong electromagnetic elds such as

high-voltage power lines or other transmitters.

■ Clean the unit with a mild detergent and a soft dry cloth. Never use any kind of

solvent or alcohol.

■ To prevent damage caused by battery leakage, remove the batteries before storage

or long period of non-use. Do not reverse battery installation. Observe positive (+)

and negative (-) markings.

■ WIRELESS MODELS (IQ200,IQ300, IQ400) Wireless computer uses an analog

wireless signal. It is not digitally coded but uses technology to lower the chance of

interference with circuitry used in other electronic devices such as lights, phones ,

computers, etc.

2012 IQ400 Computer

Setup and Owners Manual - 11/11

COMPUTER PARTS

COMPUTER INSTALLATION

The computer unit can be mounted on a bicycle handlebar or stem.

1. To mount the bracket, insert two nylon ties through the mounting bracket slots.

(a) - handlebar slots, (b) stem slots

2. Insert the rubber pad into back of mount bracket for handlebar or stem by aligning

slots in the back of the mount with the pad.

3. Position the pad/bracket onto the handlebar or stem and tighten both nylon ties

securely. Carefully snip tie ends 1-2mm from tie head.

To mount the computer onto the bracket, position it into the bracket at a 45 degree angle,

hold down and rotate the computer unit clockwise to lock it in place. To remove it, rotate

the computer counter-clockwise and lift it o.

NYLON TIES

MOUNTING BRACKET

HANDLEBAR

Check the following components before installation:

IQ400 COMPUTER UNIT

MOUNTING BRACKET WIRELESS SPEED

& CADENCE SENSOR

CADENCE MAGNET

(back)(front)

(front)

NYLON TIES (X5)

SPOKE MAGNET

SENSOR

STABILIZING PADS (X2)

MOUNTING PAD

(back)

SENSOR INSTALLATION

MAX.

150 cm

SPOKE

MAGNET

CADENCE

SENSOR PIN

GREEN LED LIGHT

SPEED

SENSOR

ARM

STABALIZING

PAD

SPOKE

MAGNET

1~5mm

CADENCE

MAGNET

ADJUSTABLE

CADENCE MAGNET

1. Loosen (DO NOT REMOVE) the screw on the adjustable Speed Sensor arm. Position

the sensor on the top of the non-drive chainstay within 150 mm of the computer. The

Cadence Sensor pin and battery door must point out toward the crank arm as shown.

2012 IQ400 Computer

Setup and Owners Manual - 11/11

2. Pass the two cable ties through the sensor mounting holes and loosely mount the

sensor body to the non-drive side chainstay (do not fully tighten the cable ties at this

point). Install the sensor stabilizing pad between the chainstay and sensor.

3. Secure the sensor to the non-drive side chainstay with 2 nylon ties. Loosely install the

sensor magnet to one of the spokes of the rear wheel. Make sure the silver side of the

magnet faces toward the sensor arm.

Adjust the position of the magnet, sensor arm and sensor together so that the magnet

passes by the full length of the sensor arm and 1-2 mm separates the magnet and

sensor arm.

4. Loosely mount the Cadence Magnet to the inside of the crank arm using 1 of the nylon

ties. Make sure the word “Sensor” faces toward the Cadence Sensor pin and a small

piece of stabilizing pad is installed between the Cadence Magnet and the crank arm.

IMPORTANT: Proper adjustment of the clearances between magnets and sensors must

be accurate for proper computer function. There are multiple ways to make accurate

adjustments and requires care when setting up the sensors.

5. Set the Speed Sensor-to-magnet and Cadence Sensor-to-magnet gaps by tilting the

sensor toward or away from pickup zone. Adjust the position of the Cadence Sensor

pin and Speed Sensor arm as needed - make sure to loosen or tighten the screw on the

front edge of the sensor body when adjusting the Cadence Sensor pin. The maximum

distance between the speed sensor and magnet on the spoke is 5 mm. The maximum

distance between the cadence sensor and magnet on the crank arm is 5mm.

6. When set, draw the nylon ties tight but do NOT fully tighten. This will allow for minor

adjustments after the computer setup is complete.

SETTING THE CLOCK (CLK)

1. Press FUNCTION until the “ ” function shows.CLK

2. Press and hold for >3 seconds to begin programming.SET

3. Press SET to change to “12H” or “24H” hour mode.

4. Press the to move the cursor to the hour eldFUNCTION

5. Press SET hour.

6. Repeat steps 4 and 5 to set Minutes and Seconds.

7. Press and hold the button for 3 seconds to exit programming.FUNCTION

GENERAL NOTES FOR PROGRAMMING ALL FUNCTIONS:

• Press and hold for 3 seconds to begin programming a function. SET

• Press the to change the value of a selected eld. Press/hold SET to change SET

value rapidly.

• Press the button to move the cursor to the next eld. FUNCTION

• Press and hold the button for 3 seconds to exit programming.FUNCTION

To begin using the computer, simply press the button. Following installation, FUNCTION

the computer is activated automatically by a rotating wheel.

There are 2 power saving modes - 50% savings if no movement after 5 minutes, 100%

power savings after 30 minutes.

Press the button to exit the power saving modes prior to using the computer.SET

Press the button, to switch the computer through the following functions: FUNCTION

“CLK” – Clock feature, in 12/24 hr format

“TM” – Time ridden for 1 ride

“AVS” – Average speed for 1 ride

“MXS” – Maximum speed for 1 ride

“A. CAD” - Average cadence per minute for 1 ride

- Maximum cadence for 1 ride“M. CAD”

“DST” - Distance ridden for 1 ride

“ODO” – Total miles ridden for all rides

“KCAL” – Calories burned (estimate) for 1 ride

“DAILY” – Distance ridden in the past 24 hours

“SCAN ” – Computer display scans all functions. Press the FUNCTION button to stop

scanning.

To turn on the backlight, press and release the button. The backlight will stay SET

on for three (3) seconds.

“TM, AVS, MXS, DST, and KCAL“ are recorded automatically as soon as the wheel moves.

A CAD and M CAD are automatically recorded as soon as the crank moves. Recording stops

if the wheel stops. Cadence recording stops if the crank stops. To clear this information,

press and hold the button in the “TM” mode.SET

Main Display anD Functions

CURRENT SPEED

SPEED SCALE

SUB-DISPLAY MODE

SET Button

(back of unit)

FUNCTION Button

FUNCTIONS DISPLAY

CADENCE

MOTION SIGNAL **This button also,

activates the display

backlighting.

SETTING CALORIES BURNED (KCAL)

This computer can estimate calories burned while riding. The estimate is based on weight,

gender, time ridden and average speed. IMPORTANT: The estimate is truly an estimate.

Actual calories burned will vary depending on many variables the computer does not

calculate such as heart rate.

1. Press FUNCTION until the “ ” displays.KCAL

2 Press and hold for >3 seconds to begin programming.SET

3. Press SET to select gender “MALE” or “FEMALE”.

4. Press FUNCTION to store gender.

5. Press SET to change weight unit “Kg” or “Lb”.

6. Press FUNCTION to begin entering your weight in unit selected.

7. Press or hold Set to change the weight. Range: 0 ~ 150 Kg, 0-330 Lb.

8. Press and hold the Function for 3 seconds to exit programming.

RESETTING THE ODOMETER (ODO)

If the battery is replaced, it is possible to update the odometer to the mileage on your bike

after replacing the battery.

1. Press FUNCTION until the “ ” displays.ODO

2. Press and hold for >3 seconds to begin programming.SET

3. Press FUNCTION until “00000” (ve zeros) and “ ” appears on the screenODO

4. Press SET to change the appropriate numbers. Press to change cursor FUNCTION

position.

5. Repeat step 4 until the odometer is set.

6. Press and hold for 3 seconds to exit programming.FUNCTION

7. Verify the computer shows speed and cadence. If not, you may have to complete the

Final Set Up steps shown in these instructions.

2012 IQ400 Computer

Setup and Owners Manual - 11/11

1. Press FUNCTION until the “ ” displays.ODO

2. Press and hold for >3 seconds to begin programming.SET

3. Press SET to change to “KM/H” or “M/H”

4. Determine your then nd the corresponding in the chart below.Tire Size L (mm)

5. Press FUNCTION to move the cursor to the rst eld.

6. Press SET to change the 1st digit of 4 numbers for the .L (mm)

Repeat steps 5 and 6 until the proper is entered.L (mm)

7. Press and hold for 3 seconds to exit programming.FUNCTION

8. Verify the computer shows speed and cadence. If not, you may have to complete the

Final Set Up steps shown in these instructions.

SETTING THE WHEEL SIZE

L (mm)

tire size l (mm) tire size l (mm)

24 X 1.75 1890 27 X 1-3/8 2169

24 X 2.00 1925 650 X 20C 1938

24 X 2.125 1965 650 X 23C 1944

26 X 7/8 1920 650 X 35A 2090

26 X 1(59) 1913 650 X 38A 2125

26 X 1(65) 1952 650 X 38B 2105

26 X 1.25 1953 700 X 18C 2070

tire size l (mm) 26 X 1-1/8 1970 700 X 19C 2080

14 X 1.50 1020 26 X 1-3/8 2068 700 X 20C 2086

14 x 1.75 1055 26 X 1-1/2 2100 700 X 23C 2096

16 X 1.50 1185 26 X 1.40 2005 700 X 25C 2105

16 X 1.75 1195 26 X 1.50 2010 700 X 28C 2136

18 X 1.50 1340 26 X 1.75 2023 700 X 30C 2146

18 X 1.75 1350 26 X 1.95 2050 700 X 32C 2155

20 X 1.75 1515 26 X 2.00 2055 2130700C Tubular

20 X 1-3/8 1615 26 X 2.10 2068 700 X 35C 2168

22 X 1-3/8 1770 26 X 2.125 2070 700 X 38C 2180

22 X 1-1/2 1785 26 X 2.35 2083 700 X 40C 2200

24 X 1 1753 26 X 3.00 2170 29 X 2.1 2288

24 X 3/4 Tubular 1785 27 X 1 2145 29 X 2.3 2326

24 x 1-1/8 1795 27 X 1-1/8 2155

24 X 1-1/4 1905 27 X 1-1/4 2161

IMPORTANT: After the computer is programmed, nal set up must be conrmed.

1. Install the computer onto the mounting bracket.

2. Gently spin the wheel. Verify the Speed and Cadence magnets to not hit the sensor

arms.

3. Gently spin the cranks then check the display to verify the Speed and Cadence are

showing on the computer. The green LED light on the sensor should also ash verifying

proper set up. If either is not appearing on the sreen and the LED is not ashing, adjust

the gaps between magnets. Spin the cranks again.

4. If the speed or cadence do not appear on the screen after steps 1-3 are complete, you

may have to pair the sensor to the computer again.

4a. With the computer mounted, press and hold the SET and FUNCTION buttons at the

same time for 5 seconds.

4b. Turn the cranks. A 2 digit ID code between “00-63” will appear on the screen. Press

the SET button. Turn the cranks when the Sub-Display ashes lines “--------”. Continue

turning the cranks for 10 seconds. Pairing is complete when the computer returns to

the home screen.

4c. If “ERR” appears in the screen, repeat steps 1 through 4b.

5. When all setup including sensors and magnets is complete, draw the nylon ties securely.

Carefully snip the tie ends 1-2mm from tie head.

FINAL SET UP

TROUBLESHOOTING

CONDITION ACTION

Wheel moving but current speed does not

appear

Check/adjust sensor and magnet gap.

Battery is low –> replace

“ERR01” appears on display Battery low –> replace

“ERR” appears on display

Interference from another electronic

device-> turn o or move electronic

device

Display is blank, very light or black Battery low –> replace.

Computer too hot –> move to cool area.

Display changes slowly Computer too cold –> move to warm

area

IQ400 Specications

Operating Temperature 0° C ~ 40° C, ( 32° F ~ 104°F)

Storage Temperature -10° C ~ 50° C, ( 14° F ~ 122°F)

Battery 3 volt lithium, CR2032 cell

Weight 30.6 grams

Timer Range: 0~29 (hour): 59 (minute): 59 (second)

Current Speed Range: 0 ~ 99.9 KM/ 0~62 Mile

Average Speed Range: 0 ~ 99.9 KM/ 0~62 Mile

MAX Speed Range: 0 ~ 99.9 KM/ 0 ~ 62 Mile

(Trip) Distance Range: 0 ~ 999.99 KM/ 0~600 Mile

Odometer Range: 0 ~ 99999 KM/ 0 ~ 62000 Mile

BATTERY REPLACEMENT

Remove the computer from the handlebar mount. Use a coin to unscrew the battery door.

Turn counter-clockwise. Remove the old battery. Place a new battery (CR2032) into the

computer with the positive “+” marking of the battery facing up. Replace the battery door.

Follow these steps for replacing the sensor battery (CR2032).

Verify the computer shows speed and cadence. If not, you may have to complte the Final

Set Up steps shown in these instructions.

CANNONDALE USA

Cycling Sports Group, Inc.

172 Friendship Road,

Bedford, Pennsylvania, 15522 , USA

(Voice): 1-800-BIKE-USA

(Fax): 814-623-6173

custserv@cyclingsportsgroup.com

CANNONDALE EUROPE

Cycling Sports Group Europe, B.V.

mail: Postbus 5100

visits: Hanzepoort 27

7570 GC, Oldenzaal, Netherlands

(Voice): + 41 61.4879380

(Fax): 31-5415-14240

servicedeskeurope@cyclingsportsgroup.com

CANNONDALE AUSTRALIA

Cycling Sports Group Australia Pty Limited

Unit 8, 31-41 Bridge Road

Stanmore, NSW 2048, Australia

(Voice): 61-2-85954444

(Fax): 61-2-85954499

cannondale@cyclingsportsgroup.com.au

CANNONDALE JAPAN

Namba Sumiso Building 9F,

4-19, Minami Horie 1-chome,

Nishi-ku, Osaka 550-0015, Japan

(Voice): 06-6110-9390

(Fax): 06-6110-9361

cjcustserv@cannondale.com

CANNONDALE UK

Cycling Sports Group

Vantage Way, The Fulcrum,

Poole, Dorset, BH12 4NU

(Voice): +44 (0)1202 732288

(Fax): +44 (0)1202 723366

sales@cyclingsportsgroup.co.uk

CANNONDALE CONTACT INFORMATION

Specyfikacje produktu

Marka:	Cannondale
Kategoria:	komputer rowerowy
Model:	IQ400

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Cannondale IQ400, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje komputer rowerowy Cannondale

Cannondale IQ118 Instrukcja

19 Września 2024

Cannondale IQ400 Instrukcja

16 Września 2024

Cannondale IQ200 Instrukcja

15 Września 2024

Cannondale IQ100 Instrukcja

15 Września 2024

Cannondale IQ300 Instrukcja

14 Września 2024

Instrukcje komputer rowerowy

Najnowsze instrukcje dla komputer rowerowy

BBB BCP-35W Instrukcja

12 Października 2024

Wahoo Elemnt Roam v2 Instrukcja

9 Października 2024

VDO R4 Instrukcja

7 Października 2024

VDO R5 Instrukcja

7 Października 2024

Sigma Eox View 1700 Instrukcja

7 Października 2024

IGPSport BSC100 Instrukcja

7 Października 2024

IGPSport iGS800 Instrukcja

7 Października 2024

Lezyne Super Instrukcja

5 Października 2024

Crivit HG01734A Instrukcja

4 Października 2024

Cateye Quick CC-RS100W Instrukcja

3 Października 2024