Instrukcja obsługi Britax KIDFIX II XP SICT

Britax fotelik samochodowy KIDFIX II XP SICT

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Britax KIDFIX II XP SICT (2 stron) w kategorii fotelik samochodowy. Ta instrukcja była pomocna dla 16 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/2

01 02

Belt guide (bright red)

Release knob

XP-SICT (only KIDFIX II XP SICT)

Belt holder (dark red)

ISOFIX insertion aids

ISOFIX fastening points (automobile)

ISOFIT locking arms

Backrest

SecureGuard

ISOFIT adjustment button

Safety button

Storage compartment

XP-PAD

Adjusting handle of the headrest

Removing the seat cover

1. Moving the headrest of the vehicle seat into the top

position.

2. Unhook the cover hook 19 on the rear of the backrest.

3. Remove the top part of the cover and fold it forwards to

the seat surface.

4. Unhook the cover hook 19 on the front of the backrest.

5. Pull the cover o of the seat surface.

Removing the headrest cover

Unhook the cover loop

on the rear of the backrest.

7. Unhook the cover hook 19 on the front of the backrest.

Pull o the cover of the headrest

►The cover can now be washed.

Please observe the

instructions on the washing label of the cover:

Re-ﬁtting the cover

Proceed in reverse order to put on the cover.

5. CARE AND MAINTENANCE

Seat cushion

2. INTRODUCTION

Thank you for choosing

KIDFIX II XP / KIDFIX II XP SICT

to keep your child

safe through a new stage of their life.

In order to protect your child correctly, the

KIDFIX II XP / KIDFIX II XP

SICT

must always be used and installed as described in these instructions.

If you have any further questions regarding its use, please feel free to contact us:

These instructions use the following symbols stated below:

Symbol Keyword Explanation

DANGER! Risk of severe personal injury

WARNING! Risk of minor personal injury

CAUTION! Risk of material damage

TIP: Useful notes

Instructions that follow a set sequence are numbered.

Example:

1. Press the button...

Belt guide colours

For better dierentiation, the two vehicle seat

belts are highlighted in dierent colours. The

diagonal seat belt 17 in dark red and the lap belt

16 in bright red. The colour of the belt guides

on the child safety seat follows the same colour

scheme.

4. USE IN THE VEHICLE

Please observe the instructions for using children's restraining systems in the operating instruc-

tions of your vehicle. ISOFIX anchoring systems (see type The seat can be used in vehicles with

list) and in vehicles with a

3-point belt.

Please ﬁnd the information on the seats approved for child safety seats of the weight classes 15 to

36 kg in the operating instructions of your vehicle

The is approved for two dierent methods of installation:

KIDFIX II XP / KIDFIX II XP SICT

Symbol Installation type Approval type Section

with the ISOFIT locking arms on the

ISOFIX fastening points in the vehicle.

Observe the vehicle type list.

semi-

universal

with the vehicle's 3-point seatbelt universal 9B

a) This means that the child safety seat may only be used in vehicles that are listed in the

vehicle type list enclosed. This type list is consistently kept up to date. The latest version can

be obtained from us or from www.britax.com

You can use your child safety seat as follows:

In the direction of travel Yes

Against the direction of travel No

with 2-point belt No

with 3-point belt2) Yes

with ISOFIX fastening points

(between seat surface and

backrest)

Yes

on front passenger seat Yes

on outer rear seat Yes

on centre rear seat (with

3-point belt) Yes 4)

1) Use is permitted on a rearward-facing vehicle seat (e.g. in a van or minibus) only if the vehicle

seat is also approved for use by adults. The seat may not be in the area of eect of an airbag.

2) The safety belt must be approved to ECE R 16 or a comparable standard (see test label on

belt with an "E" or "e" in a circle).

3) If there is a front airbag: Slide the vehicle seat a long way back and refer to any instructions

in vehicle owner's manual.

4) Cannot be used if the vehicle seat is equipped with only a 2-point belt.

15-36 kg

3. CERTIFCATION

BRITAX RÖMER

Vehicle child safety

seat

Testing and certiﬁcation

In accordance with ECE* R 44/04

Group Body weight

KIDFIX II XP

KIDFIX II XP SICT

II+III 15 to 36 kg

*ECE = European Standard for Child Safety Equipment

The child safety seat has been designed, tested and certiﬁed according to the

requirements of the European Standard for Child Safety Equipment (ECE R

44/04). The seal of approval E (in a circle) and the approval number are located

on the orange approval label (sticker on the child safety seat).

This approval will be invalidated if you make any modiﬁcations to DANGER!

the child safety seat. Only the manufacturer is permitted to make

modiﬁcations to the child safety seat. The child seat is approved

for use both with and without XP-PAD.

WARNING! Use the

KIDFIX II XP / KIDFIX II XP SICT

exclusively for

securing your child in your vehicle. It is in no way suitable as a

seat or toy in the home.

Never secure your child or the child safety seat with a 2-point DANGER!

belt. If you secure your child in the child seat with only a 2-point

belt, then in the event of an accident this may cause serious

injuries to your child, possibly resulting in death.

PAGE I

6. DISASSEMBLY AND DISPOSAL

Please ensure that you only use the original BRITAX RÖMER replacement seat

covers, as the seat cover is an integral part of the child safety seat and fulﬁls

important functions to ensure the smooth operation of the system. Replacement

seat covers are available from your dealer.

• The cover can be removed and washed with a mild detergent in the delicates

programme of the washing machine (30 °C). Please observe the instructions on

the washing label of the cover.

• The plastic parts and the XP-PAD can be cleaned with a soap sud. Do not use

any caustic cleaning agents (such as solvents).

DANGER! The child seat must not be used without the seat cover.

1. PRODUCT OVERVIEW

1. Operate the release key of your vehicle seat buckle

2. Open the XP-PAD 11 on the Velcro fastener and

remove the diagonal belt 17 .

3. Open the dark red belt holder 03 by pressing

backwards the key on the belt holder 03 and

unthreading the diagonal belt 17 .

Only for installation type A (ISOFIT):

4. To release the ISOFIT fastening, release the green

safety button 08 and the red release button 07 ﬁrst

on the one and the on the other side opposite on

another.

►The child safety seat can now be removed.

The child safety seat must always be DANGER!

secured when it is in the vehicle, even if

no child is being transported.

DISPOSAL:

Please observe the waste disposal regulations in your country.

Disposal of packaging Container for cardboard boxes

Seat cover Residual waste, thermal utilisation

Plastic parts According to the labelling in the

corresponding container

Metal parts Container for metals

Belt straps Container for polyester

buckle and tongue Residual waste

17 11

0807

REMOVAL:

UNFASTENING YOUR CHILD:

1. To unfasten your child, use the release button of your vehicle seat buckle.

TIP! The XP-PAD can remained applied for easier use on the diagonal belt

of your vehicle, the diagonal belt must be retensioned before every journey;

see: [page II].Section10 step 12

KIDFIX II XP

KIDFIX II XP SICT

User instructions

www.britax.com

2000022092 - 05/16

15 kg - 36 kg

(~4 Y - 12 Y)

Britax Childcare

Britax Römer

Kindersicherheit GmbH

Blaubeurer Strasse 71

D-89077 Ulm

Germany

T.: +49 (0) 731 9345-199/-299

F.: +49 (0) 731 9345-210

E.: service.de@britax.com

www.britax.com

Britax Childcare

Britax Exelsior Limited

1 Churchill Way West

Andover

Hampshire SP10 3UW

T.: +44 (0) 1264 333343

F.: +44 (0) 1264 334146

E.:

service.uk@britax.com

www.britax.com

6. Place the XP-PAD 11 in the side of the child safety

seat closer to the vehicle door.

8. Place the child safety seat in driving direction on

a vehicle seat approved for use.Ensure that the

backrest 14 is ﬂush with the backrest of the vehicle

seat .

9. Position the two ISOFIT locking arms 06 directly in

front of the two insertion aids 02 .

10. Push both ISOFIT locking arms 06 into the insert

guides 02 until the ISOFIT locking arms 06 engage

on sides with a clicking sound. both

DANGER! The green safety button 08 must be

visible on both sides so that the child

safety seat is correctly fastened.

11. Hold the ISOFIT

settings button 09 down and push

the child safety seat as far back as possible.

1. Carry out the steps in Section 8 "ADJUSTING THE

HEADREST".

2. Place the XP-PAD 11 on the side of the child safety

seat closer to the vehicle door.

3. Guide the elastic holding strap of the XP-PAD 11

into the dark red belt holder 03 of the headrest 22

until it lies completely in the belt holder 03 and is

not twisted.

4. Place the child seat on the vehicle seat. Ensure that

the backrest 14 is ﬂush with the backrest of the

vehicle seat.

Tip! If the headrest of the vehicle seat gets in the

way, turn it the other way.

5. Carry out the steps in Section 10 "SECURING

YOUR CHILD".

12. Shake the child safety seat to ensure that it is

securely fastened and check again the fastening

buttons 08 to ensure that are fully green. both

13. Carry out the steps in Section 10 "SECURING

YOUR CHILD".

For the safety of your child, before every journey in the car check that...

►the child safety seat is slotted in on both sides with the ISOFIT locking arms

06 in the ISOFIT fastening points 01 and both safety buttons 08 are fully

green;

►the child safety seat is securely fastened;

►the lap belt 16 runs in the bright red belt guides on both sides of the seat

cushion 05 ,

►the

lap belt

runs through the bright red

SecureGuard 10 .

►the diagonal seat belt section 17 on the side of the vehicle seatbelt buckle

18 also runs through the light red belt guide 05 of the seat cushion,

►the diagonal seat belt section 17 runs through the dark red belt holder 03 of

the headrest,

►XP-PAD 11 and XP-SICT 04 are correctly installed and used,

►the diagonal seat belt section 17 runs diagonally backward,

►the straps are tight twisted and not ,

►the seatbelt buckle 18 must not be positioned on the red belt guide 05 in

the seat cushion.

DANGER!

If your child try to use to open the vehicle belt buckle 18 or

introduce the diagonal belt section 17 into the bright red SecureGuard 10 ,

stop as soon as possible. Check whether the child safety seat is correctly

fastened and ensure that your child is correctly secured. Explain to your

child the dangers associated with his actions.

7. SAFETY NOTES

Please take the time to read these instructions carefully and keep them

to hand in the intended storage compartment 13 on the child safety seat

at all times! The instructions must be with the child safety seat if the latter

is passed on to a third party.

DANGER! For the protection of your child:

• In the event of an accident with a collision speed of more than 10 km/h, the

child safety seat may be damaged without the damage becoming immediately

visible. In this case the child safety seat must be replaced. Please dispose of

it properly.

• As a rule, have your child safety seat checked if it was damaged (e.g if it falls

on the ground).

• Regularly check all important parts for damage. Ensure that all mechanical

parts, in particular, are fully functional.

• Never lubricate or oil parts of the child seat.

•

Never leave your child unattended in the child seat in the vehicle.

• Only allow your child to enter and exit the vehicle on the pavement side.

• Protect the child safety seat from intensive direct sunlight when it is not in use.

The child safety seat can get very hot in direct sunshine. Child skin is sensitive

and could thereby be harmed.

•

The more snugly the belt ﬁts over your child's body, the better they will be

protected. Therefore avoid putting thick clothes on your child under the belt.

• Take regular breaks on long journeys in order to give your child the

opportunity to play around.

• Use on the rear seat: Move the front seat forward far enough that you child's

feet cannot hit the backrest of the front seat (to prevent risk of injury).

DANGER! For the protection of all vehicle occupants:

In the case of an emergency stop or an accident, unsecured persons or objects

may cause injury to other vehicle occupants. Please always check that...

• the backrests of the vehicle seats are locked (i.e. that any foldable rear seat

bench latch is engaged).

• all heavy or sharp-edged objects in the vehicle (e.g. on the parcel shelf) are

secured.

• all persons in the vehicle have their seatbelts fastened.

• the child safety seat is always secured when it is in the vehicle, even if no child

is being transported.

WARNING! For your protection when handling the child seat:

• Never use the child safety seat free-standing, not even for test sitting.

• The backrest 14 may tip backward. Always place the child seat on the vehicle

seat before having your child sit down in it.

• When swivelling up the backrest 14 , nothing must come between the

backrest 14 and the seat cushion 15 . You or your child could pinch your

ﬁngers, injuring them.

•

To avoid damage, ensure that the child safety seat is not jammed in between

hard objects (car door, seat rails, etc.).

•

Keep the child safety seat in a safe place when it is not in use. Do not place any

heavy objects on the seat and do not store it directly next to sources of heat or

in direct sunlight.

CAUTION! To protect your vehicle:

•

Certain car seat covers made from more sensitive materials (e.g. velour, leather,

etc.) may sustain signs of wear and tear when using child safety seats. For

optimum protection of your car seat covers, we recommend using the BRITAX

RÖMER car seat protector from our range of accessories.

PAGE II

For the safety of your child, before every journey in the car check that...

►the child safety seat is securely fastened;

►the lap belt

runs in the bright red belt guides on both sides of the seat

cushion

►the

lap belt

runs through the bright red

SecureGuard 10 .

►the diagonal seat belt section 17 on the side of the vehicle seatbelt buckle

18 also runs through the light red belt guide 05 of the seat cushion,

►the diagonal seat belt section 17 runs through the dark red belt holder 03

of the headrest,

►the diagonal seat belt section 17 runs diagonally backward,

►the straps are tight twisted and not ,

►XP-PAD 11 and XP-SICT 04 are correctly installed and used,

►the seatbelt buckle 18 must not be positioned on the red belt guide 05 in

the seat cushion.

DANGER! If your child try to use to open the vehicle belt buckle 18 or

introduce the diagonal belt section 17 into the bright red SecureGuard 10 ,

stop as soon as possible. Check whether the child safety seat is correctly

fastened and ensure that your child is correctly secured. Explain to your

child the dangers associated with his actions.

A correctly set headrest 22 ensures that the diagonal seat belt section 17 is

optimally positioned, and gives your child optimum protection.

The headrest 22 must be adjusted so that there is a space two ﬁngers wide

between the headrest 22 and your child's shoulders.

To adjust the height of the headrest to ﬁt your child:

1. Reach into the adjustment handle 12 on the back

of the headrest 22 and pull it towards you.

This unlocks the headrest.

2. You can now move the unlocked headrest 22 to

the desired height. As soon as you release the

adjustment handle 12 , the headrest 22 will lock

into place.

3. Place the child safety seat on the vehicle seat.

4. Have your child sit down in the child safety seat and

check the height. Repeat the procedure until the

headrest 22 has the correct height.

1. If your vehicle is not ﬁtted with ISOFIX insertion aids by standard, clamp

the two insertion aids 02 , with are included in the scope of delivery of the

seat*, with the section pointing upwards to the two ISOFIX fastening points

01 of your vehicle.

TIP!

The ISOFIX fastening points are located between the surface and the backrest

of the vehicle seat.

* aids facilitate the installation of the child safety seat with the The insertion

use of the SOFIX fastening points and prevent damage to the car seat covers.

As long as they are not used, remove them and keep them in a safe place. For

vehicles with foldable a backrest, the insertion aids need to be removed before

folding the backrest. Any problems occurring usually come from soiling or ex-

ternal objects on the insertion aids and on the hook. Remove soiling or external

objects to rectify such problems.

2. Moving the headrest of the vehicle seat into the top position.

3. Carry out the steps in Section 8 "ADJUSTING THE HEADREST".

8. ADJUSTING THE HEADREST

9. INSTALLATION

With ISOFIT + 3-point belt

The

KIDFIX II XP / KIDFIX II XP SICT

is installed permanently in the vehicle with

the ISOFIT locking arms.

Your child is then buckled into the child seat with the vehicle's 3-point seatbelt.

4. Hold the ISOFIT settings button 09 down and push

the ISOFIT locking arms 06 out in full .

KIDFIX II XP SICT & KIDFIX II XP:

1. Let your child sit in the child safety seat and place

the XP-PAD 11 over the chest area of your child.

If you ﬁnd that the retraction force of the 3-point seat

belt is not enough to ensure that the seat belt is tight

(against the child), the child seat can be used without

XP-PAD 11 ; see Chapter 3 “APPROVAL” [PAGE I].

2. Pull out the vehicle belt and guide it in front of your

child to the vehicle seat buckle 18 .

DANGER! Ensure the vehicle belt is not twisted, as

otherwise the full protective eect of the

retaining system is not ensured.

3. Engage the buckle tongue in the vehicle seat buckle

18 with a CLICK!

4. Place the diagonal seat belt section 17 and lap

belt section 16 on the side of the vehicle seatbelt

buckle 18 into the light red belt guide 05 of the seat

cushion.

DANGER! The vehicle seatbelt buckle must not

be positioned between the light red belt

guide and the armrest. 18 05

5. Also place the lap belt section 16 on the other side

of the seat cushion in the light red belt guide 05 .

DANGER! The lap belt section 16 must lie as low

as possible over your child's hips on both

sides.

7. Guide the diagonal seat belt section 17 into the dark

red belt holder 03 of the headrest 22 until it lies

completely in the belt holder 03 and is not twisted.

Tip! If the backrest

conceals the belt holder

you can adjust the headrest

upwards. The diagonal

seat belt section

can now be easily inserted. Now

return the headrest

to the proper height.

8. Ensure that the diagonal belt 17 runs over the collar-

bone of your child and is not on the neck and that

the key on the belt holder is 03 fully closed.

Tip! You can still adjust the height of the headrest 22

again here in the vehicle.

9. Open the Velcro fastener on the XP-PAD 11 and fold

the top part of the XP-PAD 11 to the side.

10. Insert the diagonal belt 17 in the die nubby surface

of the XP-PAD 11.

11. Close the XP-PAD 11 again by folding the folded

part back and closing the Velcro fastener.

DANGER! The diagonal seat belt section 17 must

run diagonally backward. You can adjust

the course of the belt with your vehicle's

adjustable belt deﬂector.

DANGER! The diagonal belt 17 must never be

directed forwards to the belt deﬂector

on the vehicle. In this case, use the child

safety seat on the back seat only.

12. Tighten the vehicle seat belt by pulling on the diagonal

seat belt section

13. Observe the further steps of the relevant installation

type.

KIDFIX II XP SICT:

Unscrew the XP-SICT

04 anti-clockwise (on the side

closer to the vehicle door) until it has a distance of 5

mm to the vehicle door or has been unscrewed to the

maximum.

5. Push the green safety button

and the red release

button

on both sides of the seat towards each

other. This ensures that both hooks on the ISOFIT

locking arms

are open and ready to use.

10. SECURING YOUR CHILD

UNFASTENING YOUR CHILD AND REMOVAL:

To unfasten your child or to remove the child safety seat, observe the steps in

Section 6 "REMOVAL AND DISPOSAL" [PAGE I]

2212

0807

16 05

17 11

The

KIDFIX II XP / KIDFIX II XP SICT

is not installed permanently in the vehicle. It

is simply secured together with your child using the vehicle's 3-point seatbelt.

With 3-point belt

7. Guide the elastic holding strap of the XP-PAD 11

into the dark red belt holder 03 of the headrest 22

until it lies completely in the belt holder 03 and is not

twisted.

UNFASTENING YOUR CHILD AND REMOVAL:

To unfasten your child or to remove the child safety seat, observe the steps

in Section 6 "REMOVAL AND DISPOSAL" [PAGE I]

Adjusting the backrest:

The backrest 14 is connected to the seat cushion 15 by

an articulated axis. The backrest 14 of the child seat can

be adjusted to any inclination of the vehicle seat.

Please know that optimal protection is guaranteed only if

the vehicle seat is in an upright position.

0602

6. Guide the lap belt section 16 into the bright red

SecureGuard 10.

DANGER!

Do not guide the diagonal the section

into the bright red SecureGuard

10 16

Specyfikacje produktu

Marka:	Britax
Kategoria:	fotelik samochodowy
Model:	KIDFIX II XP SICT
Kolor produktu:	Szary
Szerokość produktu:	540 mm
Głębokość produktu:	390 mm
Waga produktu:	7300 g
Ilość:	1
Grupa:	2-3 (15 - 36 kg; 3.5 - 12 lat)
Typ zapięcia pasów:	3-punktowy
Regulowane oparcie:	Tak
Typ mocowania:	ISOFIX
Łatwa instalacja:	Tak
Wysokość (min):	670 mm
Wysokość (max.):	850 mm
Regulacja wysokości pasa:	Tak
Kolorystyka:	Monochromatyczny