Instrukcja obsługi Boss NX694
Boss
Autospeaker
NX694
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Boss NX694 (2 stron) w kategorii Autospeaker. Ta instrukcja była pomocna dla 3 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek
Strona 1/2
NX694
Installation Instructions
800 Watts / 6” x 9” (152 x 229 mm)
4-Way Full Range Speakers (1 Pair)
- 1 -
Thank you for purchasing a BOSS Audio Systems product. Please read through these
instructions carefully so you will know how to install this product properly.
Package Contents
• 2x Speakers
• 2x Speaker wires with polarity connectors
• 8x Mounting screws and clip nuts
• Installation Instructions/ Cutout Template/
Warranty
Specications
• 4-way full range system
Woofer: 6” x 9” (152 x 229 mm),
polypropylene cone, rubber surround
Tweeter: 2x 0.71” (18 mm), dome
Midrange: 2.28” (58 mm), dome
• Output power: max 800 W
• Nominal impedance: 4 Ω
• Frequency response: 45 Hz-20 kHz
• Sensitivity: 89 dB (1 watt/1 meter)
Speaker dimensions
a
b
a
b
e
f
c
d
g
a. Overall diameter: 9.25” x 6.42” / 235 x 163 mm
b. Mounting hole diameter:
8.55” x 5.85” (217 x 149 mm)
c. Mounting depth: 3.47” (88 mm)
d. Grill protrusion: 1.3” (33 mm)
e. Overall speaker with grill:
10.2” x 7.52” (259 x 191 mm)
f. Tweeter protrusion: 0.44” (11 mm)
g. Outer motor diameter: 4.97” (126 mm)
Customer service: 805-751-4853
Tech support: www.bossaudio.com/support
- 2 -
Installation
You can t the speakers in the factory speaker openings in a vehicle, or create a cutout in a vehicle for speaker
installation.
Consult an expert when in doubt about installation. Professional installation is always recommended.
Prior to installation, disconnect the negative terminal of the vehicle battery.
If you must modify the vehicle for the speaker installation, make sure you do not impair the safety and
structural integrity of the vehicle.
Before you drill or cut any holes, investigate your vehicle’s layout very carefully. Take special care when
you work near the fuel tank, fuel lines, hydraulic lines and electrical wiring.
Option 1: Mounting in the factory speaker location
1. Make sure the factory speaker opening (e.g. in the door or kick panel) ts the speaker in size.
2. Remove the panel which hides the factory speaker locations, and then remove the old speaker.
3. Connect the speaker to the factory speaker wiring with correct polarity. If factory speaker wiring is corroded,
use supplied speaker wires.
4. Fasten the speaker into the factory opening with the supplied screws. Some vehicles may require a speaker
mounting adapter.
Make sure the speaker sits ush across the entire mounting surface.
Make sure the newly installed speaker does not interfere with any operations (e.g. windows rolling all the way
down if in a door, or trunk mechanism if in the rear deck, etc.)
5. Perform a quick test, then reinstall the panel. Be sure to properly break in speakers and not reach max volume
until after two 20 minute cycles at regular volume.
Option 2: Mounting in a new location
1. Remove the interior vehicle panel (e.g. from the door or rear deck) where the speakers are to be mounted.
2. Cut a mounting hole and screw holes on the mounting surface as follows:
• Verify the supplied template matches the speaker and mounting cut-out.
• Cut out the template along the cut line. Use the cut-out template to mark the mounting hole and screw holes
on the mounting surface. Then cut the holes for the speaker to be mounted.
3. Slide the speaker from the top into the hole, and correctly place the supplied speaker grill over the top.
4. Fasten the speaker with four supplied screws and clip nuts.
Make sure the speaker sits ush across the entire mounting surface.
Make sure the newly installed speaker does not interfere with any operations (e.g. windows rolling all the way
down if in a door, or trunk mechanism if in the rear deck, etc.)
5. Using the supplied speaker wires, connect the speaker to the source unit.
6. Perform a quick test, then reinstall the panel. Be sure to properly break in speakers and not reach max volume
until after two 20 minute cycles at regular volume.
Wiring
• Make sure the speakers are wired correctly at 4 ohms. Observe speaker polarity when making connections.
• Avoid routing wires near any sharp or moving parts. Run wires away from other wires that may cause unwanted
noise. Insulate bare wires properly.
• Connect the supplied speaker wires to the speakers as follows:
Connect the plug ends of the speaker wires to the speaker terminals, the red wire to the positive terminal and
the black wire to the negative terminal. Make sure the wires are rmly attached to the terminals.
0322
Specyfikacje produktu
| Marka: | Boss |
| Kategoria: | Autospeaker |
| Model: | NX694 |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Boss NX694, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Autospeaker Boss
3 Października 2024
15 Września 2024
14 Września 2024
13 Września 2024
10 Września 2024
Instrukcje Autospeaker
- Autospeaker Sony
- Autospeaker Pioneer
- Autospeaker JBL
- Autospeaker Blaupunkt
- Autospeaker Kenwood
- Autospeaker Alpine
- Autospeaker Memphis Audio
- Autospeaker Auna
- Autospeaker Audiotec Fischer
- Autospeaker Fusion
- Autospeaker Magnat
- Autospeaker Pyle
- Autospeaker JL Audio
- Autospeaker Hifonics
- Autospeaker Focal
- Autospeaker Kicker
- Autospeaker Mac Audio
- Autospeaker Hertz
- Autospeaker Crunch
- Autospeaker Caliber
- Autospeaker Autotek
- Autospeaker Lanzar
- Autospeaker Dnt
- Autospeaker Axton
- Autospeaker Mtx Audio
- Autospeaker Sinus Live
Najnowsze instrukcje dla Autospeaker
5 Października 2024
4 Października 2024
3 Października 2024
3 Października 2024
3 Października 2024
3 Października 2024
3 Października 2024
2 Października 2024
23 Września 2024
22 Września 2024