Instrukcja obsługi Boss BCB-1000

Boss odbiornik BCB-1000

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Boss BCB-1000 (1 stron) w kategorii odbiornik. Ta instrukcja była pomocna dla 3 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/1
*5100075081-02*
© 2020 Roland Corporation
Owner’s Manual
BCB-1000 Pedal Board Before using this unit, carefully read “USING THE UNIT SAFELY” and “IMPORTANT NOTES.” After reading, keep the document(s)
where it will be available for immediate reference.
Main Specications
Connectors
INPUT Jack (1/4” phone type)
SEND Jack (1/4” phone type)
RETURN A/B Jack (1/4” phone type)
OUTPUT A/B Jack (1/4” phone type)
Dimensions 558 (W) x 354 (D) x 194 (H) mm
22 (W) x 14 (D) x 7-5/8 (H) inches
Pedal
installation
dimensions
496 (W) x 293 (D) x 94 (H) mm (front)
496 (W) x 293 (D) x 80 (H) mm (back)
19-1/2 (W) x 11-1/2 (D) x 3-3/4 (H) inches (front)
19-1/2 (W) x 11-1/2 (D) x 3-1/8 (H) inches (back)
Weight 6.7 kg (14 lbs 13 oz)
Accessories Owner’s Manual
• This document explains the specications of the product at the time that the document was issued. For
the latest information, refer to the Roland website.
Eect Unit Installation Examples
By using the slits in the plate to route the cables behind the plate, you can hide the cabling to get a clean layout.
* You can install a commercially available power supply under the plate.
* To secure the eect units, use commercially available hook-and-loop fasteners.
Removing the Plate
If you want to route cables behind the plate, your work will be easier if you remove the plate from the bottom case.
To remove the plate from the bottom case, turn the bottom case over and loosen the coin screws at the four corners.
* Take care that the plate does not fall when you loosen the coin screws.
* When attaching the plate to the bottom case, make sure that the cables you installed are not pinched between the bottom case and the
plate, and then tighten the coin screws.
Plate
Bottom Case
Coin screws
Loosen
Tighten
Before You Use the Case
Parts and functions of the top case
A
C
B
Top Handle
Use this to carry the case.
Pulling Handle
Use this to pull the case.
By pulling the handle out while pressing the
button, you can adjust the length.
D
Side Handle
Casters
Use these to pull the case.
* Note that malfunctions may occur if sand
or dust adheres to the casters, or if threads
wrap around them.
B
Attaching the top case
Before carrying the case, align the four fasteners of the top case with the bottom case, and press
the fasteners inward until you hear them click into place.
Connecting the Equipment
Simply connect the INPUT/OUTPUT jacks of the plate to your guitar and amp, and you’re ready to perform.
To connect the pedals, use the SEND/RETURN jacks located on the back of the plate.
1 INPUT jack
Connect your guitar.
2 OUTPUT A jack
Connect your guitar amp.
3 OUTPUT B jack
Connect your guitar amp.
Use these for stereo output, or if you want an output that
is separate from the OUTPUT A jack.
4 SEND jack
This outputs the signal that is input to the INPUT jack.
Connect this to the input of your eect unit.
5 RETURN A jack
Connect this to the output of your eect unit. The signal
is output to the OUTPUT A jack.
6 RETURN B jack
Connect this to the output of your eect unit. The signal
is output to the OUTPUT B jack.
12 3
4 5 6
USING THE UNIT SAFELY
WARNING
Do not disassemble or modify by yourself
Do not carry out anything unless you are instructed to
do so in the owner’s manual. Otherwise, you risk causing
malfunction.
Do not repair or replace parts by yourself
Be sure to contact your dealer, a Roland service center, or
an ocial Roland dealer.
For a list of Roland service centers and ocial Roland
dealers, refer to the Roland website.
Do not place in an unstable location
Otherwise, you risk injury as the result of the unit toppling
over or dropping down.
Be cautious to protect children from injury
Always make sure that an adult is on hand to provide
supervision and guidance when using the unit in places
where children are present, or when a child will be using
the unit.
Do not drop or subject to strong impact
Otherwise, you risk causing damage or malfunction.
CAUTION
Avoid climbing on top of the unit, or placing heavy objects on it
Otherwise, you risk injury as the result of the unit toppling
over or dropping down.
Take care so as not to get ngers pinched
When handling the following moving parts, take care
so as not to get ngers, toes, etc., pinched. Whenever a
child uses the unit, an adult should be on hand to provide
supervision and guidance.
• Case
• Handles
• Plate
Keep small items out of the reach of children
To prevent accidental ingestion of the parts listed below,
always keep them out of the reach of small children.
• Removable Parts
Coin screws
CAUTION
Take care not to injure your ngers, etc.
When handling the plate, take care that the edge of the
openings or components do not cut your ngers, etc.
Take care to avoid burns
The casters might be hot after the unit has been pulled.
Take care not to burn yourself.
Use the pulling Handle correctly
Do not lift the unit by the pulling Handle, or apply
excessive force to the pulling Handle. Doing so might cause
damage or malfunctions.
Do not use the casters inappropriately
Do not use the casters on stairsteps or when there are
dierences in level; use the handles of the unit instead.
Using the casters in an inappropriate situation might cause
damager or malfunction.
IMPORTANT NOTES
Placement
• Depending on the material and temperature of the surface on
which you place the unit, its rubber feet may discolor or mar
the surface.
Maintenance
• Never use benzine, thinners, alcohol or solvents of any kind, to
avoid the possibility of discoloration and/or deformation.
Additional Precautions
• When disposing of the packing carton or cushioning material
in which this unit was packed, you must observe the waste
disposal regulations that apply to your locality.
• When opening/closing the cover, please be careful not to get
your ngers pinched between the movable part and the unit.
In places where small children are present, make sure that an
adult provides supervision and guidance.
Intellectual Property Right
• Roland and BOSS are either registered trademarks or
trademarks of Roland Corporation in the United States and/
or other countries.
• Company names and product names appearing in this
document are registered trademarks or trademarks of their
respective owners.
For EU Countries
Roland Corporation
2036-1 Nakagawa, Hosoe-cho, Kita-ku, Hamamatsu, Shizuoka 431-1304, JAPAN
Roland Corporation
ENA 23 Zone 1 nr. 1620 Klaus-Michael Kuehnelaan 13, 2440 Geel, BELGIUM
Importer:
Manufacturer:
For EU Countries
Roland Corporation
2036-1 Nakagawa, Hosoe-cho, Kita-ku, Hamamatsu, Shizuoka 431-1304, JAPAN
Roland Europe Group Limited
Hive 2, 1530 Arlington Business Park, Theale, Reading, Berkshire. RG7 4SA United Kingdom
Importer:
Manufacturer:
For the U.K.
For details on the BCB-1000, refer to the BOSS website.
https://www.boss.info/global/products/bcb-1000/
For BOSS cables, refer to the BOSS website (Accessories).
https://www.boss.info/global/categories/accessories/boss_cables/
Used for instructions intended to alert the
user to the risk of injury or material
damage should the unit be used
improperly.
* Material damage refers to damage or
other adverse effects caused with
respect to the home and all its
furnishings, as well to domestic animals
or pets.
Used for instructions intended to alert the
user to the risk of death or severe injury
should the unit be used improperly.
The symbol alerts the user to things that must be
carried out. The specific thing that must be done is
indicated by the design contained within the circle. In the
case of the symbol at left, it means that the power-cord
plug must be unplugged from the outlet.
The symbol alerts the user to important instructions or
warnings.The specific meaning of the symbol is
determined by the design contained within the triangle. In
the case of the symbol at left, it is used for general
cautions, warnings, or alerts to danger.
The symbol alerts the user to items that must never be
carried out (are forbidden). The specific thing that must
not be done is indicated by the design contained within
the circle. In the case of the symbol at left, it means that
the unit must never be disassembled.
About WARNING and CAUTION Notices About the Symbols
ALWAYS OBSERVE THE FOLLOWING
When you need repair service, access this URL and nd your nearest Roland
Service Center or authorized Roland distributor in your country.
https://roland.cm/service
Roland Service Centers and Distributors
Roland Service Centers and Distributors
1

Specyfikacje produktu

Marka: Boss
Kategoria: odbiornik
Model: BCB-1000

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Boss BCB-1000, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje odbiornik Boss

Boss

Boss DD-500 Instrukcja

12 Stycznia 2025
Boss

Boss PT3000 Instrukcja

11 Stycznia 2025
Boss

Boss Acoustic Singer Live LT Instrukcja

15 Grudnia 2024
Boss

Boss Acoustic Singer Live Instrukcja

15 Grudnia 2024
Boss

Boss WAZA-AIR BASS Instrukcja

15 Grudnia 2024
Boss

Boss Elite BE10ACP.WX Instrukcja

7 Października 2024
Boss

Boss Elite BE9ACP.XC Instrukcja

7 Października 2024
Boss

Boss Elite BE10ACP.XC Instrukcja

7 Października 2024
Boss

Boss AR1600.2 Instrukcja

7 Października 2024
Boss

Boss AR1500M Instrukcja

5 Października 2024

Instrukcje odbiornik

Najnowsze instrukcje dla odbiornik

Marantz

Marantz SR-8000 Instrukcja

15 Stycznia 2025
AKAI

AKAI AM-32 Instrukcja

15 Stycznia 2025
Peavey

Peavey CKd 608 Instrukcja

15 Stycznia 2025
OSD Audio

OSD Audio Nero HTX4150 Instrukcja

14 Stycznia 2025
S.M.S.L

S.M.S.L PA200 Instrukcja

14 Stycznia 2025
Pyle

Pyle PFMRA340BB.5 Instrukcja

13 Stycznia 2025
Wavtech

Wavtech link700.4plus Instrukcja

13 Stycznia 2025
Behringer

Behringer NU6000DSP Instrukcja

12 Stycznia 2025
Denon

Denon DRA-935R Instrukcja

12 Stycznia 2025
Kenwood

Kenwood KMM-BT508DAB Instrukcja

12 Stycznia 2025