Instrukcja obsługi BlueStar WR060MLPLT
BlueStar
Okap wyciągowy
WR060MLPLT
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla BlueStar WR060MLPLT (34 stron) w kategorii Okap wyciągowy. Ta instrukcja była pomocna dla 11 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek
Strona 1/34

Ventilation Hood
Installation Instructions
Designer Hoods

TABLE OF CONTENTS
Safety Instructions 1
Safety Procedures 2
Wall Hood Installation
Installation Instructions 3
Wall Hood 600 CFM In-– Hood Fan (8” Round) 5
Wall Hood 600 CFM In-– Hood Fan (8” Transition) 6
Chimney & Island Hood 600 CFM In-Hood Fan 7 –
Wall Hood 1200 CFM In-Hood Fan 8 –
Chimney & Island Hood -1200 CFM In-Hood Fan 9
Island Hood Installation
Installation Instructions 10
Island Duct Cover Installation 11
Island Duct Work Installation 12
Remote Fan Installation 13
Metal Liner Installation
Installation Instructions 15
Transition Installation & Removal 16
Electrical Connections 18
Compact Metal Liner Sloped Sides 19
Metal Liner Sloped Sides 20
Professional Metal Liner Sloped Sides 21
Metal Liner Flat Sides 22
Chimney Hood Installation
Installation Instructions 23
Alternate Installation Instructions 26
Installing Rear Discharge Through Duct Cover 27
Installing a 600CFM Fan in a 30” Wide Hood 28
Wiring a Remote Fan 29
Use & Care
Bae Filters, Grease Troughs and Lights 30
Cleaning Recommendations 31
Troubleshooting Tips 32

PLEASE READ COMPLETE INSTRUCTIONS BEFORE PROCEEDING.
INSTALLATION MUST COMPLY WITH ALL LOCAL CODES.
IMPORTANT: Save these instructions for the local electrical inspector’s use.
INSTALLER: Please leave these instructions with this unit for the owner.
OWNER: Please retain the instructions for future reference.
SAFETY WARNING: Turn power circuit OFF at the service panel and lock panel door before
wiring this unit.
IMPORTANT SAFETY INSTRUCTIONS
CAUTION To reduce the –
risk of a rangetop grease re.
1. Never leave cooktop surface
unattended while on high
setting
2. Boil overs cause smoke and
greasy spillovers may ignite.
Heat oils slowly on low or
medium settings.
3. Hood fan should always be
ON when cooking on high
heat or when ambeing
foods (i.e. Crepes Suzette,
Cherries Jubilee, Peppercorn
Beef Flambe.)
4. Clean in-hood fans
frequently. Do not allow
grease to accumulate on fan
or bae lters.
5. Always use cookware
appropriate for the size of the
surface element.
CAUTION To reduce the –
risk of re, electric shock, or
injury to people, observe the
following:
1. Use this rangehood only in
the manner intended by the
manufacturer. If you have
any questions, contact the
manufacturer – Prizer
Hoods.
2. Before servicing or cleaning
the unit, switch power o at
service panel and lock the
panel to prevent the power
from being switched on
accidentally. When switched
o for service, attach a tag to
the service panel to indicate
power has been switched o
for maintenance.
3. Install this rangehood only
with remote fan models rated
maximum 12.8A or in-hood
fans manufacturered by
Prizer Hoods, CFM300,
CFM600, CFM1200.
CAUTION To reduce the –
risk of injury to people, in the
event of a rangetop grease re,
observe the following:
1. SMOTHER FLAMES with a
tight tting lid, cookie sheet
or other metal tray.
Immediately turn the gas
burner OFF. NEVER USE
WATER, wet dish-cloths or
towels as a violent steam
explosion will occur.
2. PREVENT BURNS. If gas
ames do not extinguish
immediately: EVACUATE
AND CALL THE FIRE
DEPARTMENT.
3. NEVER PICK UP A
FLAMING PAN as you may
sustain burns.
4. Use re extinguisher only if:
•You know you have a class
ABC extinguisher, and you
know how to operate it.
•Fire is small & contained in
the area where it started.
•Fire department is being
called.
•You can ght the re with
your back to an exit.
CAUTION: FOR GENERAL VENTILATION
USE ONLY. DO NOT USE TO EXHAUST
HAZARDOUS OR EXPLOSIVE MATERIALS
OR VAPOR.
HOOD SHAPES & DIMENSIONS CAN VARY
WITHOUT NOTIFICATION. NO HARDWARE
IS SUPPLIED FOR INSTALLATION
3

SAFETY PROCEDURES FOR INSTALLING YOUR
NEW PRIZER HOOD (continued)
CAUTION reduce the risk of re, electric shock, or injury to people, observe the following: –To
CAUTION For general ventilation use only. Do not use to exhaust hazardous or explosive materials or –
vapors.
1. Installation work and electrical wiring must be done by a qualied installer in accordance with all applicable
codes and standards, including re-rated construction.
2. Sucient air is needed for proper combustion and gas exhaustion through the ue to prevent backdrafting.
Follow the manufacturer’s guidelines and safety standards such as those published by the National Fire Protection
Association (NFPA), and the American Society of Heating, Refrigeration and Air Conditioning Engineers
(ASHRAE), and the local building code authorities.
3. When cutting/drilling into a wall or ceiling, avoid damage to electrical wiring and other hidden utilities.
4. In-hood or in-line fans must be vented to the outdoors.
5. All range hoods should be connected to a dedicated, non-GFCI circuit to prohibit damage to components.
6. NEVER place a control switch where it can be reached from a tub or shower.
7. CAUTION To reduce the risk of re within walls or roofs, use only metal ductwork. –
8. Install this hood in accordance with all requirements specied by the manufacturer of your cooktop/range.
9. Install this hood using required clearance from cooking surface to combustible material specied in cooktop
installation instructions.
READ & SAVE: UPON RECEIVING YOUR HOOD
•Any damage must be reported to Prizer Hoods prior to
installation. Once installed, no returns will be
accepted.
•The high degree of craftsmanship in the construction
and nish of your hood requires careful handling to
ensure proper installation.
•Do not remove your hood from its carton until you are
ready to hang it.
•Do not store your hood anywhere other than within the
carton. If it is necessary to remove your hood from the
carton, place it on a blanket or padded area that will
protect your hood from scratches or indentations.
•Remove all rings, watches, belt buckles and jackets
(snaps/zippers) to prevent scratches on the hood.
•Wearing cotton gloves are preferred. They will protect
the surface from ne scratches and eliminate
ngerprints.
•Do not lift the hood by its utensil rail. Place your
ngers under the lower reveal of the hood. Grasp
rmly and lift.
•If applicable, do not remove the protective covering
from your hood until the installation process is
complete. It will be necessary to remove only a small
portion on the back side for a wall mounted hood in
order to position in place.
•Located within the hood cavity (behind the baes) are
component parts and halogen bulbs.
4

1. The hood is shipped with the back panel and the transition. (Note: The transition is shipped upside down
within the hood and can be ipped for rear discharge if desired. It must be removed then reinstalled See –
Figures 1 though 3)
2. Detach the transition from the back panel removing four (4) screws. These shipping screws are needed for
re-attaching the transition to the back panel.
3. Secure the transition to the top of the back panel, using the four (4) screws provided. Use duct tape to seal
the joints of the transition and the top of the back panel. (See Figure 2)
4. Secure the back side of the hood to wall stud following building code in your area. (See Figure 3)
WALL HOOD INSTALLATION
5

WALL HOOD INSTALLATION (continued)
1. Add 2” x 4” wood framing block to aid in securing the
top and rear of the hood to the wall. (See Figure 6)
2. To mount CFM300, CFM600 and CFM1200 fans within
hood walls. (See Figures 8, 9, 10 & 11)
3. Install the fan by aligning the fan holes with the PEM
studs on the back panel. Tighten the fan to the panel
using the hex nuts provided. (See Figures 8, 9, 10 & 11)
4. Connect the “Molex” from the fan to the “Molex” plug on
the hood. (See Figure 4 from previous page)
5. Attach three wires: black, white and green (#16 AWG) in
½” conduit from the service panel to the hood junction
box. Power supply must be rated for 120v, 60Hz, 15
amps (minimum).
6. Remove the junction box from the rough-in plate.
Connect black wire to power supplied black wire, white
wire to power supplied white wire and green wire to
ground supplied green wire.
7. Place all wiring connectors inside junction box.
OPTIONAL DUCT COVER
1. Install the hood as described in “Hood Rough in Plate Mount” (Note: -
Be sure to allow enough room for duct cover width on the top section
of the rough-in plate.
2. Slide duct cover into opening.
3. Attach Duct Cover from the inside of the hood through lter opening
using screws. (See Figure 7) Note: Do not completely tighten screws
until all components have been installed. At this point, check the
alignment of the duct to the hood. First tighten the four corners to
secure the duct, then tighten the remaining screws.
6

CFM 600 IN-HOOD FAN
WALL APPLICATION – 8” ROUND COLLAR
7

CFM 600 IN-HOOD FAN
WALL APPLICATION – 8” TRANSITION
8

CFM 600 IN-HOOD FAN
CHIMNEY AND ISLAND APPLICATION– 8” TRANSITION
9

CFM 1200 IN-HOOD FAN
WALL APPLICATION – 10” TRANSITION
10

CFM 1200 IN-HOOD FAN
CHIMNEY AND ISLAND APPLICATION – 10” TRANSITION
10

INSTALLATION
WARNING: To reduce the risk
of re, use only metal ductwork.
1. Decide the placement of the
ductwork between the hood
and the outside of the home.
Your island hood has a top
discharge which will run
vertically.
2. When not installing a remote
fan, always install a roof cap
or wall cap. Connect rigid
round metal ductwork to the
roof cap and work back
towards the hood location.
3. Use duct tape to seal the
joints between the ductwork
sections.
4. A transition with backdraft
damper is included with your
island hood. It is
recommended that the
enclosed backdraft damper
be used in all installations.
PREPARATION
1. When installing a duct cover,
the duct cover must be
installed prior to the hood
installation. See Figure 14
for duct cover installation
instructions.
2. Remove the bae filters from
hood shell. (See Figure 12)
3. The hood is shipped with the
transition attached. The
transition is shipped upside
down in the top of the hood
and must be removed then
reinstalled.
4. Detach the transition from the
hood by removing the (4)
shipping screws. DO NOT
discard these screws. These
shipping screws will be
needed for the reinstallation
of the transition to hood.
5. Invert the transition (the
round collar points away from
top of hood). Use the
shipping screws removed
from step 4.
6. When installing a remote fan,
drill a 7/8” hole through hood
framing for conduit wiring
where needed. See Figure 13
IMPORTANT NOTES:
•Do not place electrical wiring
within the duct work itself.
•All island hoods must exhaust
to the outdoors.
ISLAND HOOD INSTALLATION
11

ISLAND DUCT COVER INSTALLATION
12

ISLAND HOOD DUCT WORK INSTALLATION
1. Cut a 10” diameter opening in
the ceiling to accommodate the
duct work necessary for proper
ventilation.
2. Transfer the overall dimensions
of the hood top plate onto the
nished ceiling/unfinished
surface. The top plate width
and overall width will vary
with the size of the hood.
3. Construct the frame using
unistrut or wood 2x4’s. Due to
the weight of the hood,
structural support is necessary.
(See Figure 3)
4. Locate and mark the center of
the hood. Attach two wood
2x4’s across the top of the
ceiling joists. (See Figure 3)
5. Drill four 3/8” holes in the
2x4’s to match the pattern on
the top of the hood. (See
Figure 3)
6. Remove hood bae lters
prior to installation of hood.
(See Figure 12)
WARNING: Framing must be
structurally tied together and
attached to the ceiling joists to
provide enough strength to
support the weight of the hood
and the internal blower, if
applicable.
WARNING: Island hoods are
very heavy. A minimum of three
installers are required to lift the
hood to the ceiling.
WARNING: When making any
electrical connections, make sure
electrical power is turned o at
the power source (or circuit
breaker) before proceeding.
7. Connect 10” round duct-work to
the hood transition using sheet
metal screws and/or duct tape.
8. Complete all electrical
connections. (See Wiring
Diagram, pg 22)
9. Align hood and tighten all nuts
until hood surface is ush with
ceiling. Install #10 x 2” screws
through remaining hood
mounting holes near top edge of
hood surface. This additional
support is necessary.
10. If installing an in-hood or in-line
fan, -install bae DO NOT re
lters until blower installation is
complete. (See in-hood fan
installation instructions)
13

REMOTE FAN
ROOF MOUNT OR WALL MOUNT
14

15

CHECK LOCATION
•If your installation has been roughed-in (including ductwork and wiring), be certain there is nothing in the way
of the mounting, pipes, other wiring etc.
•If the installation has not been roughed in, check what is needed to create the framing and mounting hardware
(all threads, nuts etc.). Be sure the location will not interfere with wiring, other utilities, or structural
considerations.
METAL LINERS TYPICAL INSTALLATION –
METAL LINER INSTALLATION
19
Specyfikacje produktu
Marka: | BlueStar |
Kategoria: | Okap wyciągowy |
Model: | WR060MLPLT |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z BlueStar WR060MLPLT, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Okap wyciągowy BlueStar

22 Września 2024

22 Września 2024

22 Września 2024

22 Września 2024

22 Września 2024

22 Września 2024

22 Września 2024

22 Września 2024

22 Września 2024

22 Września 2024
Instrukcje Okap wyciągowy
- Okap wyciągowy Bauknecht
- Okap wyciągowy Ikea
- Okap wyciągowy Samsung
- Okap wyciągowy Tesy
- Okap wyciągowy Bertazzoni
- Okap wyciągowy Electrolux
- Okap wyciągowy DeLonghi
- Okap wyciągowy AEG
- Okap wyciągowy Balay
- Okap wyciągowy Beko
- Okap wyciągowy Teka
- Okap wyciągowy LG
- Okap wyciągowy Küppersbusch
- Okap wyciągowy Smeg
- Okap wyciągowy Gram
- Okap wyciągowy Amica
- Okap wyciągowy Gorenje
- Okap wyciągowy Etna
- Okap wyciągowy LERAN
- Okap wyciągowy Sharp
- Okap wyciągowy Cookology
- Okap wyciągowy Russell Hobbs
- Okap wyciągowy Dometic
- Okap wyciągowy Bosch
- Okap wyciągowy Candy
- Okap wyciągowy Whirlpool
- Okap wyciągowy Miele
- Okap wyciągowy Midea
- Okap wyciągowy Toolcraft
- Okap wyciągowy Lamona
- Okap wyciągowy Hisense
- Okap wyciągowy Berg
- Okap wyciągowy Infiniton
- Okap wyciągowy Panasonic
- Okap wyciągowy Baumatic
- Okap wyciągowy OK
- Okap wyciągowy Hoover
- Okap wyciągowy Tesla
- Okap wyciągowy Westinghouse
- Okap wyciągowy Maytag
- Okap wyciągowy GE
- Okap wyciągowy Orbegozo
- Okap wyciągowy Blaupunkt
- Okap wyciągowy Brandt
- Okap wyciągowy Vivax
- Okap wyciągowy Siemens
- Okap wyciągowy Grundig
- Okap wyciągowy Haier
- Okap wyciągowy KKT Kolbe
- Okap wyciągowy Cylinda
- Okap wyciągowy Jocel
- Okap wyciągowy Silverline
- Okap wyciągowy Blomberg
- Okap wyciągowy Honeywell
- Okap wyciągowy Concept
- Okap wyciągowy Fisher & Paykel
- Okap wyciągowy ECG
- Okap wyciągowy Indesit
- Okap wyciągowy Ilve
- Okap wyciągowy Viking
- Okap wyciągowy Nodor
- Okap wyciągowy CATA
- Okap wyciągowy Broan
- Okap wyciągowy Hotpoint
- Okap wyciągowy V-Zug
- Okap wyciągowy Ariston Thermo
- Okap wyciągowy Zelmer
- Okap wyciągowy PKM
- Okap wyciągowy Unox
- Okap wyciągowy Thor
- Okap wyciągowy Amana
- Okap wyciągowy Dacor
- Okap wyciągowy Hotpoint Ariston
- Okap wyciągowy Furrion
- Okap wyciągowy Bomann
- Okap wyciągowy InAlto
- Okap wyciągowy Meireles
- Okap wyciągowy Schneider
- Okap wyciągowy MPM
- Okap wyciągowy CDA
- Okap wyciągowy Sam Cook
- Okap wyciągowy Philco
- Okap wyciągowy Neff
- Okap wyciągowy Corbero
- Okap wyciągowy Zanussi
- Okap wyciągowy Thermex
- Okap wyciągowy Fagor
- Okap wyciągowy Everdure
- Okap wyciągowy Thomson
- Okap wyciągowy Ardo
- Okap wyciągowy Klarstein
- Okap wyciągowy Coyote
- Okap wyciągowy Witt
- Okap wyciągowy Wolkenstein
- Okap wyciągowy Cecotec
- Okap wyciągowy Artusi
- Okap wyciągowy KitchenAid
- Okap wyciągowy Imperial
- Okap wyciągowy Helios
- Okap wyciągowy Sôlt
- Okap wyciągowy Exquisit
- Okap wyciągowy Bartscher
- Okap wyciągowy Hestan
- Okap wyciągowy Privileg
- Okap wyciągowy Dimplex
- Okap wyciągowy Falmec
- Okap wyciągowy Arçelik
- Okap wyciągowy Hanseatic
- Okap wyciągowy Continental Edison
- Okap wyciągowy Linarie
- Okap wyciągowy Atag
- Okap wyciągowy Rosieres
- Okap wyciągowy Franke
- Okap wyciągowy Novy
- Okap wyciągowy Rommer
- Okap wyciągowy Inventum
- Okap wyciągowy SVAN
- Okap wyciągowy Euro Appliances
- Okap wyciągowy Mora
- Okap wyciągowy Caple
- Okap wyciągowy AEG-Electrolux
- Okap wyciągowy Omega
- Okap wyciągowy Comfee
- Okap wyciągowy Classique
- Okap wyciągowy Kenmore
- Okap wyciągowy Kaiser
- Okap wyciągowy Zephyr
- Okap wyciągowy VOX
- Okap wyciągowy Hiberg
- Okap wyciągowy AYA
- Okap wyciągowy Pelgrim
- Okap wyciągowy Frilec
- Okap wyciągowy Orima
- Okap wyciągowy Rex
- Okap wyciągowy Kernau
- Okap wyciągowy Aspes
- Okap wyciągowy Weller
- Okap wyciągowy Twin Eagles
- Okap wyciągowy Respekta
- Okap wyciągowy Technika
- Okap wyciągowy Seiki
- Okap wyciągowy JennAir
- Okap wyciągowy Frigidaire
- Okap wyciągowy Matrix
- Okap wyciągowy Barazza
- Okap wyciągowy Summit
- Okap wyciągowy Gemini
- Okap wyciągowy Sirius
- Okap wyciągowy Foster
- Okap wyciągowy Chef
- Okap wyciągowy Fulgor Milano
- Okap wyciągowy Kelvinator
- Okap wyciągowy Gaggenau
- Okap wyciągowy Elica
- Okap wyciągowy Asko
- Okap wyciągowy Esatto
- Okap wyciągowy Signature
- Okap wyciągowy Porter & Charles
- Okap wyciągowy Kunft
- Okap wyciągowy Robinhood
- Okap wyciągowy Becken
- Okap wyciągowy Scandomestic
- Okap wyciągowy Ignis
- Okap wyciągowy Guzzanti
- Okap wyciągowy Venmar
- Okap wyciągowy Belling
- Okap wyciągowy De Dietrich
- Okap wyciągowy ZLine
- Okap wyciągowy Constructa
- Okap wyciągowy Proline
- Okap wyciągowy Euromaid
- Okap wyciągowy BLANCO
- Okap wyciągowy Scancool
- Okap wyciągowy Thermador
- Okap wyciągowy Bestron
- Okap wyciągowy Zanker
- Okap wyciągowy Kluge
- Okap wyciągowy Acec
- Okap wyciągowy Airlux
- Okap wyciągowy ABK
- Okap wyciągowy Ariston
- Okap wyciągowy Saturn
- Okap wyciągowy Progress
- Okap wyciągowy Bellini
- Okap wyciągowy Vestel
- Okap wyciągowy Itho
- Okap wyciągowy Prima
- Okap wyciągowy Junker
- Okap wyciągowy Monogram
- Okap wyciągowy Scholtes
- Okap wyciągowy Profilo
- Okap wyciągowy Heinner
- Okap wyciągowy Juno
- Okap wyciągowy Defy
- Okap wyciągowy Nordmende
- Okap wyciągowy Rangemaster
- Okap wyciągowy Boretti
- Okap wyciągowy Eico
- Okap wyciągowy Hansa
- Okap wyciągowy Air King
- Okap wyciągowy Elba
- Okap wyciągowy Steel Cucine
- Okap wyciągowy Jenn-Air
- Okap wyciągowy Limit
- Okap wyciągowy Freggia
- Okap wyciągowy Edesa
- Okap wyciągowy Lofra
- Okap wyciągowy New World
- Okap wyciągowy Leisure
- Okap wyciągowy Glem Gas
- Okap wyciągowy Viva
- Okap wyciągowy M-System
- Okap wyciągowy German Pool
- Okap wyciągowy Falcon
- Okap wyciągowy Airforce
- Okap wyciągowy Ices
- Okap wyciągowy Mx Onda
- Okap wyciągowy Kleenmaid
- Okap wyciągowy Stoves
- Okap wyciągowy Faber
- Okap wyciągowy Eurotech
- Okap wyciągowy Wolf
- Okap wyciągowy Carrefour Home
- Okap wyciągowy Mepamsa
- Okap wyciągowy Upo
- Okap wyciągowy Belion
- Okap wyciągowy SIBIR
- Okap wyciągowy Sauter
- Okap wyciągowy Café
- Okap wyciągowy ARC
- Okap wyciągowy Lynx
- Okap wyciągowy FABER CASTELL
- Okap wyciągowy Tecnolux
- Okap wyciągowy Tisira
- Okap wyciągowy Cobal
- Okap wyciągowy Premier
- Okap wyciągowy Marynen
- Okap wyciągowy Axiair
- Okap wyciągowy La Germania
- Okap wyciągowy Gutmann
- Okap wyciągowy Roblin
- Okap wyciągowy Oranier
- Okap wyciągowy Bielmeier
- Okap wyciągowy Turbo Air
- Okap wyciągowy Schweigen
- Okap wyciągowy James
- Okap wyciągowy Apelson
- Okap wyciągowy Dominox
- Okap wyciągowy NuTone
- Okap wyciągowy Eudora
- Okap wyciągowy Steelmatic
- Okap wyciągowy Wells
- Okap wyciągowy Piccante
- Okap wyciągowy Kucht
- Okap wyciągowy Best
- Okap wyciągowy Wave
- Okap wyciągowy Halifax
- Okap wyciągowy Siku
- Okap wyciągowy Elin
- Okap wyciągowy High One
- Okap wyciągowy Whispair
- Okap wyciągowy Ciarra
- Okap wyciągowy XO
- Okap wyciągowy Adelberg
- Okap wyciągowy K&H
- Okap wyciągowy Cosmo
- Okap wyciągowy FAURE
- Okap wyciągowy Viali
- Okap wyciągowy Kobe
- Okap wyciągowy Qasair
- Okap wyciągowy Berbel
- Okap wyciągowy Samus
- Okap wyciągowy Royal Catering
- Okap wyciągowy Sedona
- Okap wyciągowy Vitrokitchen
- Okap wyciągowy Arthur Martin-Electrolux
- Okap wyciągowy Elektra Bregenz
- Okap wyciągowy CENDO
- Okap wyciągowy Pando
- Okap wyciągowy Applico
- Okap wyciągowy Airone
- Okap wyciągowy Trade-Wind
- Okap wyciągowy Mayer
- Okap wyciągowy Vent-A-Hood
- Okap wyciągowy HomeCraft
- Okap wyciągowy CEEM
- Okap wyciągowy Condor
- Okap wyciągowy Baumann
- Okap wyciągowy Pitsos
- Okap wyciągowy Windster
- Okap wyciągowy Conia
Najnowsze instrukcje dla Okap wyciągowy

17 Marca 2025

15 Marca 2025

14 Marca 2025

14 Marca 2025

11 Marca 2025

11 Marca 2025

10 Marca 2025

10 Marca 2025

10 Marca 2025

10 Marca 2025