Instrukcja obsługi Blebox dimmerBox

Blebox inteligentny dom dimmerBox

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Blebox dimmerBox (2 stron) w kategorii inteligentny dom. Ta instrukcja była pomocna dla 7 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/2

The device requires pre-conguration! After the rst start, select

the type of light source controlled. The incorrect selection can

cause irreparable damage to the controller and to light source.

It is forbidden to connect dierent types of light sources to the

controlled circuit as well as to change the load type with the

connected controller.

After clicking on the device name, a window will appear informing you that

you need to select the type of load (the type of lighting that the dimmerBox

will control). Go to “Settings” (icon at the top-right corner of the screen) and

select the appropriate option in the "Load Type" box.

Remember that choosing the wrong option it can cause permanently

damage to the controller and to the light source!

If you change the load type in the future, e.g. by replacing the traditional

bulbs with LEDs, rst select the load type for "None", remove old bulbs, add

new ones and in the next step change the load type to "LED bulb". Never add

to controlled circuit, dierent types of load, e.g. a traditional bulb and a LED

bulbs, or selecting the wrong load type.

After saving the settings, go to the main panel by clicking the arrow top-left

corner of the screen. Test the controller by moving the scrollbar several times

in extreme and intermediate positions - the light source should change its

brightness.

If you have connected a wall push-button, go to the settings and then in the

"Buttons" option select the type of mounted push-button - with a single

button or two buttons. Then check its work. For a single-button, a single click

will cause that the light will switch on and switch o accordingly. Holding the

push-button generates an increase in the brightness of the light source or its

attenuation. For a button with two buttons, one of the buttons is forswitch o

(single click) or dimming (hold down) while the other is for turn on increase

the intensity of the light source.

TURN ON / OFF AND DIMM 230V LIGHTING FROM ANY PLACE IN THE WORLD

Disconnect theinstallation supply voltage before installing the controller.

Remember that any mounting works should be carried out when the mains

voltage is disconnected (switch o the mains fuse or disconnect the power

cord from the mains socket).

The controller should be installed in a place protected against adverse

environmental conditions, protected from third party access - in the ush box

or inside the enclosure of the controlled device. Remember that metallic

elements (wires, housing parts) have a negative inuence on the range of the

device, and consequently the comfort of use. It is recommended that the

device be mounted in a stable and xed position. Due to the operating

voltage of the device it is necessary that the connectors of the controller be

protected against accidental contacts or short circuits, which could cause

electric shock or damage to the device.

Download the If you have an Android mobile device, free wBox application.

you will nd the application in the Play Store. For iOS devices the application

is in the App Store.

By using your mobile phone or tablet, connect it to the device wireless

network. To do this, enter to your smartphone or tablet settings, then go to

setting of the WiFi network and nd the network name „dimmerBox-

-xxxxxxxxxx” where xxxxxxxxxx is the serial number of the device. Connect to

this network.

Turn on the wBox application. A device will appear at the top of the screen. To

add it to the application, click on "plus" on the right side of the name. To

pre-congure the controller, click on the default device name.

2 FIRST START

You can also set the conguration using the web browser

of your phone / tablet. After connecting to the wireless

network of the controller, turn on the browser and go

website www.blebox.eu

brightness controller for 230v lighting

with μWiFi technology

CONNECTION DIAGRAM

light source

INSTALLATION - BASICS

User manual

SAFETY RULES Read the diagram and then proceed to install the controller. Pay particular

attention to the designation of the controller connectors. Start with power

wires - phase L (usuallybrown) and neutral N (blue). Then, connect the load. If

you only want a local control with a wall switch, connect the wall push-button

according to the diagram. To control using only your phone or Tablet, it is not

necessary to install the wall push-button.

The controller supports all types of double monostable push-button. The order

of connection of the S1 / S2 input, to the right / left push-button does not

matter at the installation stage - it can be set at a later stage of the controller

conguration.

After making sure that the device is connected in accordance with the diagram

and that there are no metal components near the controllerwhich may

accidentally cause short-circuit, start the device by turning on the power

(turning on the mains fuse or connecting the power cord to the power outlet).

Connect only in accordance with the diagram presented in the

manual. Improper connections may be dangerous, it can damage

the controller, and loss of the warranty.

Do not connect the device to loads exceeding the permitted

values.

Using dimmerBox with magnetic low-voltage (MLV) transformers

is strictly forbidden and can cause a device damage and risk of

re.

The installation of the device to a power mains that does not

meet the quality requirements dened by PN-EN 50160, will

result in the loss of the warranty.

DANGER!: Risk of electric shock! Even with the device turned o,

the outputs may be live. All assembly work should be ALWAYS

performed with the disconnected power circuit.

direct connection (as Access Point),

Wi-Fi connection via a stan- dard router,

connection with access from any location

in the world (requires only access

to the Internet)

Apple iPhone, Apple iPad, iPad Mini,

Android, computers and mobile devices

supporting HTML5

230V AC Dimmable LED,

Incandescent/Halogen,

Electronic Low-voltage (ELV)

made of polyurethane composition not

containing halogens, self-extinguishing for

thermal class B (130 °C)

230 V AC

250 W

logical, active when connected to N,

congurable

230 V AC

<1W

output phase

bi-directional, encrypted

in the ush-mounted box,

inside the wall, inside the housing

of the dimming device

IP20

2.4 GHz

μWiFi, compatible with WiFi, 802.11g

48 x 38 x 23 mm

leading edge, trailing edge

housing

supply voltage

control modes

energy consumption

maximum voltage

type of control outputs

maximum load

dimensions

communication standard

transmission type

mode

number of inputs

type of inputs

protection level

mounting method

radio frequency

compatible devices

Once you turn on the controller for the rst time, you can proceed to its

further conguration. Being connected to the WiFi network emitted by the

device, in the control panel of the wBox application select the device, then go

to “Settings” (icon at the top-right corner of the screen).

You can change the name of the device that is displayed in the wBox

application. In addition, you can change the name and password of its

generated WiFi network. Remember that changing the network name or

password will disconnect the device immediately after you click the "Save"

button, so re-connect to the device using the newly assigned network name

and password.

You can add the controller to your home WiFi network to control it through

this home network or from anywhere in the World. To do this, in the "Connect"

settings section, select a network name from the list and press "Connect". If is

required, enter the WiFi network password. During the connection of the

controller to your home network, the phone / tablet may disconnected from

the network. In this case, you will need to reconnect your phone / tablet to the

controller network.

Please remember that in order to control the device outside the local WiFi

network, from anyplace in the World by using the wBox application, the

option "Remote access enabled" in the controller settings must be set to "Yes".

Once you've nished conguring the WiFi network, you can disconnect your

phone/tablet from the controller network and connect your mobile device

directly to your home WiFi network. The control from the wBox application

will work the same way as when the phone / tablet is connected to the

controller network. If the user leaves the local network, for example, leaving

home or using the mobile data, the wBox application will signal this state as

"Remote mode". In this case, the devices can be controlled, but for security

reasons settings are not available.

ACCESS POINT AND WIFI NETWORK SETTINGS

TECHNICAL SPECIFICATIONS

for more information visit our website

www.blebox.eu

or send us an email to: info@blebox.eu

support is available at support@blebox.eu

ADDITIONAL INFORMATION

SOFTWARE UPDATE

LOCATION AND TIME OF THE DEVICE,

SCHEDULE

To update the software in the controller, connect it to your home WiFi network

(see "Access Point and WiFi settings" section) which is connected to the

Internet. Go to “Settings” (icon at the top-right corner of the screen) and click

the "Get new rmware" button in the nal section on settings. Wait about 1

minute, do not close the interface and don’t perform other actions. The device

will download the latest software. The software version number, hardware

version and device identier can be read at the bottom of the settings screen.

The controller has the ability to work according to a given schedule. To make

this possible, set the device's time. Go to settings in the "Device time" section,

click "Change timezone". Then select your region and location from the list,

conrm your selection clicking the "Save" button. The device will synchronize

its time with the server time (if the controller is in a WiFi network with access

to Internet) or it will download time from the phone / tablet. It is recommen-

ded that the controller is always connected to a WiFi network with Internet

access so that it can automatically synchronize its clock.

To be able to control devices using the local sunrise and sunset, you must also

select the location of the controller. You can specify the location of the device

using a smartphone or tablet. In the section "Device location", click "Set

locations". Browser will ask whether to share locations - allow. In the "Coordi-

nates" eld, should appear the approximate coordinates of your location. If

the "Set locations" button blinks red with the word "Error", or the "Coordina-

tes" eld did not change the value from "Not set" to numeric data, a failurehas

occurred during the location download. You should make sure that the phone

/ tablet has a GPS module and that the sharinglocation service is enabled on

the phone.

Adding schedule entries can be performed by clicking the "Add item" button

in the "Schedule" section of settings. You can select the days in which the task

will be performed, the type of entry (at a specic time, or relative to sunrise /

sunset - only having a correctly set location) and set the parameters of the

task. The set tasks will be visible as a list, individual entries can be edited or

deleted.

lights types

Specyfikacje produktu

Marka:	Blebox
Kategoria:	inteligentny dom
Model:	dimmerBox

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Blebox dimmerBox, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje inteligentny dom Blebox

Blebox SwitchBox Instrukcja

1 Października 2024

Blebox switchBoxD Instrukcja

1 Października 2024

Blebox wLightBoxS Instrukcja

1 Października 2024

Blebox wlightbox Instrukcja

1 Października 2024

Blebox dimmerBox Instrukcja

1 Października 2024

Blebox LightBox Instrukcja

1 Października 2024

Instrukcje inteligentny dom

Najnowsze instrukcje dla inteligentny dom

Elro AB600S-2 Instrukcja

13 Października 2024

Shelly Qubino Wave 1PM Mini Instrukcja

9 Października 2024

EZVIZ DL01 Pro Instrukcja

9 Października 2024

Tenda SP15 Instrukcja

9 Października 2024

Ikea RODRET 005.597.95 Instrukcja

8 Października 2024

Acer Wave 7 Instrukcja

8 Października 2024

Ikea TRETAKT 505.565.20 Instrukcja

8 Października 2024

Ikea RODRET 505.597.93 Instrukcja

8 Października 2024

Aqara Smart Gas Detector Instrukcja

8 Października 2024

V-TAC VT-5132 Instrukcja

7 Października 2024