Instrukcja obsługi Blaupunkt THA500.1

Blaupunkt nieskategoryzowany THA500.1

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Blaupunkt THA500.1 (8 stron) w kategorii nieskategoryzowany. Ta instrukcja była pomocna dla 9 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/8
THA500.1
1 062 310 500 001
Warranty
We provide manufacturer's warranty for 12 months
from the date of sale for Blaupunkt products purchased
within India.
Recommendation
The performance of an amplier can only be as good as
its installation. Correct installation increases the overall
performance of your car sound system. The THA
amplier should be installed by a trained person. If you
would like to install it yourself, please read these
installation instructions very carefully and allow yourself
sufficient time for the installation.
In conclusion, allow us a few words about the topic of
health protection:
During playback of music in your vehicle, please
consider that continuous sound-pressure levels above
100 dB can lead to permanent damage of the human ear
& in some cases loss of hearing. Using today's high-
performance systems and loudspeaker congurations
allows for reaching sound-pressure levels above 130 dB.
Safety notes
Please observe the following safety notes during the
installation and connection.
- Disconnect the negative terminal of the battery!
Observe safety notes of the vehicle manufacturer.
- When you drill holes, ensure that you do not damage
any vehicle components.
- Please use minimum 10AWG power & ground cable
with a fuse located within 18 inches of the battery.
- Use cable glands for holes with sharp edges.
- Incorrect installation can result in malfunction of
vehicle electronic systems or sound system.
Installation and connection instructions
With respect to accident safety, the THA 500.1 must be
secured fastened at its mounting location.
When selecting the installation location, select a dry
location that offers sufficient air circulation for cooling
the amplier.
The THA 500.1 must not be installed on rear shelves, rear
seats or other locations that are open to the passenger
cabin.
The installation location must be suitable to accept the
accompanying screws and provide a rm support.
The amplier power cable must be tted with a fuse no
more than 45 cms from the battery to protect the vehicle
battery in case of a short circuit between power
amplier and battery. The fuse of the amplier protects
only the amplier, not the vehicle battery.
Use loudspeakers with 2 - 4 Ohms impedance (see table
or installation drawing). Do not connect loudspeakers to
ground, use only the referenced terminals.
Audio inputs (see Fig. 3)
You can select between 2 different audio inputs;
- Cinch (RCA)
- Hi level (loudspeaker connections)
Use only one of the audio inputs; otherwise, it may lead
to audio interference.
The preamplier outputs are connected to the cinch
(RCA) sockets ) via a shielded sound cable. j
With control via the loudspeaker outputs, the input
connections of pos. / are fed to the closest k l
loudspeaker cables (front or rear) on the left and right.
They are separated and connected to the input
connections. The polarity of the +or - connections must
be observed. Bridge output stages (BTL) can also be
connected directly without an additional adapter.
Positive / negative connection
- We recommend a minimum cross section of 10 AWG
- Route commercially available positive cable to the
battery and connect via fuse holder.
- Use cable glands for holes with sharp edges.
- Securely fasten commercially available negative
cables to a noise-free ground point (chassis screw,
chassis metal) not to the negative pole of the battery.
- Scrape the contact surfaces of the ground point until
they are bright and grease with graphite grease.
Integrated fuses (Fuse)
The fuses integrated in the amplier (Fuse) protect the
power amplier and the entire electrical system in case
of an error. If a replacement fuse is used, never bridge
fuses or replace them with a type with higher current.
1 x 500 W / 2
25 Hz - 500 Hz
> 100 dB @ RMS power
> 75 dB @ 1W/1kHz
<0.15%
0.2 / 5V
50 - 500Hz
185 x 54 x 184
7.3 x 2.1 x 7.3
0 dB / 6 dB
THA500.1 THA500.1
RMS power

Specyfikacje produktu

Marka: Blaupunkt
Kategoria: nieskategoryzowany
Model: THA500.1

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Blaupunkt THA500.1, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje nieskategoryzowany Blaupunkt

Blaupunkt

Blaupunkt BP-MF05 Instrukcja

6 Lipca 2024
Blaupunkt

Blaupunkt BP-TB05 Instrukcja

6 Lipca 2024
Blaupunkt

Blaupunkt BP-KF07 Instrukcja

5 Lipca 2024
Blaupunkt

Blaupunkt MPD 61080 A Instrukcja

5 Lipca 2024
Blaupunkt

Blaupunkt BP-MF06 Instrukcja

5 Lipca 2024
Blaupunkt

Blaupunkt BP-PJ01M Instrukcja

5 Lipca 2024
Blaupunkt

Blaupunkt BP-PJ02 Instrukcja

5 Lipca 2024
Blaupunkt

Blaupunkt BP-YF06 Instrukcja

5 Lipca 2024
Blaupunkt

Blaupunkt THA500.1 Instrukcja

5 Lipca 2024
Blaupunkt

Blaupunkt THA 285 Instrukcja

5 Lipca 2024

Instrukcje nieskategoryzowany

Najnowsze instrukcje dla nieskategoryzowany

Meec Tools

Meec Tools 010-084 Instrukcja

6 Października 2024
Outwell

Outwell Scenic Road 250 Instrukcja

5 Października 2024
Impact

Impact Qualite QL-3560-LED Instrukcja

4 Października 2024
Impact

Impact QuikBalance Instrukcja

4 Października 2024
Impact

Impact CA-112 Instrukcja

4 Października 2024
Impact

Impact Forever Ready Cool FRC-24-LED Instrukcja

4 Października 2024
Impact

Impact LS-BHA Instrukcja

4 Października 2024
Impact

Impact LKB-5C Instrukcja

4 Października 2024
Impact

Impact Varipole Drop Ceiling Adapter Instrukcja

4 Października 2024
Impact

Impact RST-001 Instrukcja

4 Października 2024