Instrukcja obsługi Black & Decker TV700
Black & Decker
Sander
TV700
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Black & Decker TV700 (16 stron) w kategorii Sander. Ta instrukcja była pomocna dla 3 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek
Strona 1/16
1
EN G L I S H
WARNING: IMPORTANT SAFETY WARNINGS
AND INSTRUCTIONS
TO REDUCE RISK OF INJURY:
• Before any use, be sure everyone using this tool reads and understands all
safety instructions and other information contained in this manual.
• Save these instructions and review frequently prior to use and in instructing
others.
WARNING: When using electric tools, basic safety precautions should
always be followed to reduce risk of fire, electric shock,
and personal injury, including the following.
READ ALL INSTRUCTIONS
GENERAL SAFETY WARNINGS AND INSTRUCTIONS
FOR ALL TOOLS
•KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries.
•CONSIDER WORK AREA ENVIRONMENT. Don’t expose power tools to rain.
Don’t use power tools in damp or wet locations. Keep work area well lit. Do not
use in presence of flammable liquids or gases. Motors in these tools normally
spark, and the sparks may ignite the fumes.
•GUARD AGAINST ELECTRIC SHOCK. Prevent body contact with grounded
surfaces. For example; pipes, radiators, ranges, refrigerator enclosures. Use
extreme caution when drilling, driving, or cutting into walls, floors, ceilings or
other areas or wherever live electrical wires may be contacted, do not touch any
metal parts of the tool. Hold the tool only by the plastic handle to prevent electric
shock.
•KEEP CHILDREN AWAY. Do not let children or visitors contact tool or extension
cord. All children and visitors should be kept away from work area.
•STORE IDLE TOOLS. When not in use, tools should be stored in dry, and high or
locked-up place–out of reach of children.
•DON’T FORCE TOOL. It will do the job better and safer at the rate for which it
was intended.
1-800-544-6986
INSTRUCTION
MANUAL
KEY INFORMATION YOU SHOULD KNOW:
•Regularly check wear on paper and replace worn paper.
•Do not push down—let sander do the work.
•Extended drywall sanding may damage the tool.
1/4 Sheet Palm Grip
Finishing Sander
TV700
VEA EL ESPAÑOL EN LA CONTRAPORTADA.
POUR LE FRANÇAIS, VOIR LA COUVERTURE ARRIÈRE.
SAVE THIS
MANUAL FOR
FUTURE REFERENCE.
If you have any questions, call
1-800-544-6986.
INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA DE
GARANTÍA. ADVERTENCIA: LÉASE ESTE INSTRUCTIVO ANTES DE USAR EL
PRODUCTO.
*TV700 / 386237 12/8/03 10:22 AM Page 1
1
Paper clamp lever
Levier de la pince
Palanca del sujetador de lija
3
2
*TV700 / 386237 12/8/03 10:22 AM Page 2
3
•USE RIGHT TOOL. Don’t force small tool or attachment to do the job of a heavy
duty tool. Don’t use tool for purposes not intended.
•DRESS PROPERLY. Do not wear loose clothing or jewelry. They can be caught in
moving parts. Rubber gloves and non-skid footwear are recommended when
working outdoors. Wear protective hair covering to contain long hair.
•USE SAFETY GLASSES AND OTHER SAFETY EQUIPMENT. Use safety goggles or
safety glasses with side shields, complying with applicable safety standards
and, when needed, a face shield. Also use face or dust mask if cutting operation
is dusty. This applies to all persons in the work area. Also use a hard hat,
hearing protection, gloves, safety shoes and dust collection systems when
specified or required.
•DON’T ABUSE CORD. Never carry tool by cord or yank it to disconnect from
receptacle. Keep cord from heat, oil, and sharp edges.
•SECURE WORK. Use clamps or a vise to hold work. It’s safer than using your
hand and it frees both hands to operate tool.
•DON’T OVERREACH. Keep proper footing and balance at all times.
•MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for better and safer
performance. Follow instructions for lubricating and changing accessories.
Inspect tool cords periodically and if damaged, have repaired by authorized
service facility. Inspect extension cords periodically and replace if damaged.
Keep handles dry, clean, and free from oil and grease.
•DISCONNECT TOOLS. Unplug the tool when not in use, when moving tool from
place to place, before servicing, and when changing accessories (such as
blades, bits, cutters) or making adjustments.
•REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see
that keys and adjusting wrenches are removed from tool before turning it on.
•AVOID UNINTENTIONAL STARTING. Don’t carry tool with finger on switch. Be
sure switch is off when plugging in.
•EXTENSION CORDS. Make sure your extension cord is in good condition.
When using an extension cord, be sure to use one heavy enough to carry the
current your product will draw.An undersized cord will cause a drop in line
voltage resulting in loss of power and overheating. The following table shows
the correct size to use depending on cord length and nameplate ampere rating.
If in doubt, use the next heavier gage. The smaller the gage number, the heavier
the cord.
•OUTDOOR USE EXTENSION CORDS. When tool is used outdoors, use only
extension cords intended for use outdoors and so marked.
•STAY ALERT. Watch what you are doing. Use common sense. Do not operate
tool when you are tired or otherwise impaired.
•CHECK DAMAGED PARTS. Before further use of the tool, a guard or other part
that is damaged should be carefully checked to determine that it will operate
properly and perform its intended function. Check for alignment of moving
parts, binding of moving parts, breakage of parts, mounting, and any other
conditions that may affect its operation. A guard or other part that is damaged
should be properly repaired or replaced by an authorized service center. Do not
use tool if switch does not turn it on and off.
•REPAIRS AND SERVICE. Repairs, maintenance and any adjustments not
specified in this manual should be performed by authorized service centers or
other qualified service organizations, always using identical replacement parts.
•USE OF ACCESSORIES AND ATTACHMENTS. The use of any accessory or
attachment not recommended for use with the tool could be hazardous. Note:
Refer to the accessory section of this manual for further details.
EN G L I S H
Minimum Gage for Cord Sets
Volts Total Length of Cord in Feet
120V 0-25 26-50 51-100 101-150
240V 0-50 51-100 101-200 201-300
Ampere Rating
More Not more American Wire Gage
Than Than
0 - 6 18 16 16 14
6 - 10 18 16 14 12
10 - 12 16 16 14 12
12 - 16 14 12 Not Recommended
*TV700 / 386237 12/8/03 10:22 AM Page 3
Specyfikacje produktu
| Marka: | Black & Decker |
| Kategoria: | Sander |
| Model: | TV700 |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Black & Decker TV700, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Sander Black & Decker
5 Października 2024
16 Września 2024
15 Września 2024
13 Września 2024
13 Września 2024
12 Września 2024
12 Września 2024
10 Września 2024
8 Września 2024
8 Września 2024
Instrukcje Sander
- Sander AEG
- Sander Worx
- Sander Milwaukee
- Sander Bosch
- Sander Parkside
- Sander Global
- Sander Toolcraft
- Sander Festool
- Sander Bavaria By Einhell
- Sander Stanley
- Sander Scheppach
- Sander Proxxon
- Sander Ribimex
- Sander Hazet
- Sander RIKON
- Sander DeWalt
- Sander Einhell
- Sander Hyundai
- Sander Silverline
- Sander Makita
- Sander Ozito
- Sander RYOBI
- Sander Flex
- Sander DEDRA
- Sander Biltema
- Sander Hilti
- Sander Trotec
- Sander Dremel
- Sander Handwerk
- Sander Meec Tools
- Sander Güde
- Sander Arendo
- Sander Bavaria
- Sander Mafell
- Sander Gastroback
- Sander DURO PRO
- Sander McKenzie
- Sander Westfalia
- Sander Ergotools Pattfield
- Sander Fein
- Sander Ferm
- Sander Hitachi
- Sander Herkules
- Sander Craftsman
- Sander Matrix
- Sander Fieldmann
- Sander Ridgid
- Sander PowerPlus
- Sander Alpha Tools
- Sander Vonroc
- Sander HiKOKI
- Sander Workzone
- Sander Porter-Cable
- Sander Metabo
- Sander Skil
- Sander Cocraft
- Sander Kinzo
- Sander Far Tools
- Sander Tryton
- Sander Tacklife
- Sander Maktec
- Sander Bort
- Sander Power Craft
- Sander Topcraft
- Sander Gamma
- Sander Kress
- Sander Duro
- Sander Varo
- Sander Max
- Sander Truper
- Sander Bruder Mannesmann
- Sander Meister Craft
- Sander Probuilder
- Sander Rupes
- Sander Batavia
- Sander Protool
- Sander Holzmann
- Sander Black Decker
- Sander Stomer
- Sander Elu
- Sander Wagner SprayTech
- Sander King Craft
- Sander Powertec
- Sander Toolson
- Sander Toledo
- Sander FIXIT
- Sander Einhell Bavaria
- Sander THUN
- Sander Prowork
- Sander Pevec
- Sander TAURUS Titanium
- Sander Stalco
Najnowsze instrukcje dla Sander
15 Stycznia 2025
11 Stycznia 2025
1 Stycznia 2025
27 Grudnia 2024
27 Grudnia 2024
27 Grudnia 2024
27 Grudnia 2024
27 Grudnia 2024
26 Grudnia 2024
26 Grudnia 2024