Instrukcja obsługi Black & Decker PKS200

Black & Decker odkurzacz PKS200

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Black & Decker PKS200 (7 stron) w kategorii odkurzacz. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/7

How to use

Before First Use and Tips

• The battery is not fully charged when packed in the carton. Charge the battery for at

least 16 hours before first use. See “Charging the Battery”.

Charging the Battery - Fig. B

RECHARGING

From new, the rechargeable cells of the product need a minimum charge time of 16 hours

to ensure full power. While charging, the product may get warm, this is perfectly normal and

safe. It can remain on charge indefinitely without damage or danger. It is not possible to

“overcharge” the battery cells with the charger provided.

• Recharge the unit by placing in the charging base. Be sure to turn off and wipe any

moisture from the unit before doing so.

• The red indicator light on the charger base will come ON indicating that the battery is

charging. The red light indicates that the charger is connected to the battery and is

charging. This light will remain Red as long as the unit is connected to the charger.

• If a battery does not charge properly:

• ensure the unit is turned off, properly seated in the charging base and the

charge indicator light is on.

• check the current at the outlet by plugging in a lamp or other appliance there

to see if it will work,

• see if the outlet is connected to a wall switch which controls the power,

• move the Charger and battery to a surrounding air temperature of +40°F

(5°C) to 105°F (40°C).

• DO NOT CONTINUE TO USE THE PALM GRIP POWER SCRUBBER with a depleted

battery.

Mounting The Charging Base:

The charging base of your Palm Grip Power Scrubber may be mounted one of the following

ways:

1. Counter mount

2. Wall mount

3. Under cabinet mount

• Consider your normal work pattern and the possible addition of other under-the-cabinet

appliances.

• Be sure to mount the palm grip power scrubber within reach of an electrical outlet.

WARNING: Important safeguards to follow when choosing the

location of the charging base:

• To reduce the risk of fire or electric shock do not operate any heating appliance beneath

the mounted unit.

• Do not mount unit over or near any portion of a heating or cooking appliance or a sink or

basin.

• Do not mount the unit behind, under, or in front of under cabinet lighting appliances.

• NEVER ATTEMPT TO USE TACKS THROUGH OR AGAINST THE CORD TO HOLD IT.

Mounting Hardware: - Fig. C

1. 3 mounting screws 4. 1 mounting bracket 7. 3 mounting screw covers

2. 1 - 1/4” cabinet spacer 5. 4 hollow wall anchors 8. mounting hole template

3. 4 - 1/2” cabinet spacers 6. 4 anchor screws

Counter Mount:

If you do not wish to mount your palm grip power scrubber to a wall or cabinet, you may

simply set the charging base on a counter within reach of an electrical outlet.

1. Install the 3 mounting screws (Fig. C, 1) into the charging base by screwing into the

mounting bracket from the top.

2. Install the 3 mounting screw covers (Fig. C, 7) by pushing onto the screws and into the

slots in the top of the charging base.

3. Plug the charger into an appropriate electrical outlet being sure the electrical cord can

not be damaged by a heat source or physical abuses such as pinching and rubbing.

Slots are provided in the sides of the charging base to assist in routing of the cord to the

outlet.

Wall mount:

NOTE: Use the hardware provided (Fig. C, 5&6) only if hanging on conventional sheet rock

or plaster walls. If not hanging on conventional sheet rock or plaster walls, please use the

appropriate fasteners for that material.

1. Remove the mounting bracket (Fig. C, 4) from the charging base by sliding it out.

2. Position the bracket on the wall where the charging base is to be located ensuring it is

level and is within reach of a suitable electrical outlet. The wall bracket should be a

WARNING: Important Safety Warnings and Instructions

When using electrical appliances, basic safety precautions should always be followed,

including the following:

PLEASE READ AND UNDERSTAND ALL INSTRUCTIONS CAREFULLY BEFORE USING

THE UNIT.

WARNING: Some cleaning products contain chemicals known to the State of

California to cause cancer, birth defects or other reproductive harm.

When using Palm Grip Power Scrubber, be sure to read cleaning

product labels for any Proposition 65 warnings. Follow directions on

containers of all such products.

WARNING: To reduce the risk of fire, electrical shock or injury:

• Close supervision is necessary when any appliance is used by or near children.

Do not allow to be used as a toy.

• To protect against risk of electrical shock, do not put Battery Charger or charging base in

water or other liquid.

• Do not operate in the presence of explosives and/or flammable fumes or liquids.

• Always wear eye protection when using the Scrubber with irritating substances.

You may also want to use rubber gloves. Read and follow manufacturer’s instructions on

the cleaning agent you use. Only use household cleaners.

• Always store unit indoors.

• Keep hair, loose clothing, and all parts of body away from moving parts.

• Do not insert or remove attachments/accessories when unit is running.

• Store out of reach of children.

• To reduce the risk of fire or electric shock do not operate any heating appliance beneath the

mounted unit.

• Do not mount unit over or near any portion of a heating or cooking appliance or a sink or

basin.

• Do not mount the unit behind, under, or in front of under cabinet lighting appliances.

• This appliance is intended for household use only and not for commercial or

industrial use.

• Use only as described in this manual. Use only Black & Decker recommended attachments.

Important Safety Instructions for the Battery And Charger

• Do not charge a battery if it is wet or shows any evidence of corrosion.

• Do not incinerate the battery. It can explode in a fire. A small leakage from the battery cell

may occur under extreme usage, charging, or temperature conditions. This does not

indicate a failure. However, if the outer seal is broken and this leakage gets on your skin:

(1) wash quickly with soap and water or (2) neutralize with a mild acid such as lemon juice

or vinegar, (3) if the liquid gets into the eyes, flush them immediately with clean water for a

minimum of 10 minutes. Seek medical attention.

NOTE: The liquid is a 20-35% solution of potassium hydroxide.

• Do not use an extension cord. Plug the Charger directly into an electrical outlet.

• Use the Charger only in a standard electrical outlet (120V/60Hz).

• Do not attempt to use this charger with any other product; do not attempt to charge this

product with any other charger. Use only the charger supplied by the manufacturer to

recharge. (charger #90500150 or 90500027)

• Do not use Charger in wet or damp conditions. It is intended for indoor use only. Do not use

the Charger near sinks, or tubs. Do not immerse in water.

• Do not allow the cord to hang over the edge of a table or counter or touch hot surfaces.

The Charger should be placed away from sinks and hot surfaces.

• Do not operate Charger with damaged cord or plug — have them replaced immediately.

• Do not operate Charger if it has received a sharp blow, been dropped, or otherwise

damaged in any way. Return the appliance to any authorized service facility for

examination, repair, or electrical or mechanical adjustment. Do not disassemble Charger.

• For best results, do not charge a battery when it or air temperature is BELOW 40°F (5°C) or

above 105°F (40°C).

• Unplug the Charger when not in use and before cleaning or maintenance.

• Do not abuse the cord. To reduce the risk of damage to the electric plug or cord, never

carry the Charger by its cord or yank the cord to disconnect; instead, grasp the Charger

plug and pull to disconnect. Keep Charger cord away from heat, oil, and sharp edges.

SAVE THESE INSTRUCTIONS

Catalog Numbers: PKS200, PKS200B FORM NO. 90500121 PRINTED IN CHINA

VEA EL ESPAÑOL EN LA CONTRAPORTADA.

SAVE THIS MANUAL FOR FUTURE REFERENCE.

Charger

Charge Indicator Light

Charging Base

Removable Drip Cup

Catalog Numbers:

PKS200, PKS200B

CONSERVER LE PRÉSENT GUIDE À TITRE DE RÉFÉRENCE.

Key Information You Should Know

• When immersing scrubber in water, DO NOT cover the unit with more than

1 meter (3 Feet) of water. Do not leave the Scrubber immersed for more

than 30 minutes.

PALM GRIP POWER SCRUBBER

INSTRUCTION MANUAL

Accessory

Scrubber

On/Off Switch

BEFORE RETURNING THIS PRODUCT

FOR ANY REASON PLEASE CALL

1-800-544-6986

BEFORE YOU CALL, HAVE THE CATALOG No. AND DATE CODE AVAILABLE. IN MOST CASES, A

BLACK & DECKER REPRESENTATIVE CAN RESOLVE THE PROBLEM OVER THE PHONE. IF YOU HAVE

A SUGGESTION OR COMMENT, GIVE US ACALL. YOUR FEEDBACK IS VITAL TO BLACK & DECKER.

THANK

HANK YOU

YOU FOR

FOR CHOOSING

CHOOSING B

BLACK

LACK &

DECKER

ECKER!

OTO

TO WWW

WWW.B

.B LACKAND

LACKANDD

DECKER

ECKER.

.COM

COM/N

/NEW

EWO

OWNER

WNER

TO REGISTER

YOUR NEW

NEW PRODUCT

PRODUCT.

FORM NO: 90501347

PALM GRIP POWER SCRUBBER MOUNTING TEMPLATE

GABARIT POUR FIXATION DE LA BROSSEUSE ÉLECTRIQUE À PRISE PALMAIRE

PLANTILLA DE MONTAJE DE LA FREGADORA ELÉCTRICA PARA LA

PALMA DE LA MANO

Line up this edge with inside surface of overhang or 1/4" - 1/2" back from front of cabinet.

Aligner ce bord avec la surface interne d u rebord ou l'éloigner de 6,3 mm à 12,7 mm

(1/4” - 1/2”) du bord ava nt de l'ar moire.

Alinee este borde c on la superﬁcie interior del alero o a 6,35 mm - 12,7 m m (1/4” - 1/2”)

de dista ncia desde la p arte frontal del gabinete.

minimum of 4" from any object above it to allow easy access to the scrubber. Mark the

screw locations using the bracket as a template. (Fig. D, 1)

WARNING: Wear eye protection to prevent injury when working with power and

hand tools.

3. Secure the mounting bracket to the wall using the provided anchors and screws

(Fig. C, 5&6) if the wall is constructed of sheetrock or similar material. Use other

fasteners as appropriate if the wall is constructed of a different material. (Fig. D, 2)

4. Slide the charging base onto the mounting bracket evenly and carefully until it comes in

contact with the wall. (Fig. D, 3)

5. Secure the charging base to the mounting bracket by screwing the 3 - mounting screws

(Fig. C,1) into the mounting bracket through the top of the charging base.(Fig. D, 4)

6. Install the (3) mounting screw pushing onto the screws and into the covers (Fig. C, 7) by

slots in the top of the charging base. (Fig. D, 5)

7. Plug the charger into an appropriate electrical outlet being sure the electrical cord can

not be damaged by a heat source or physical abuses such as pinching and rubbing.

Slots are provided in the sides of the charging base to assist in routing of the cord to the

outlet. (Fig. D, 6)

Under Cabinet Mount:

1. First, determine if your cabinet has a flush (flat) bottom — or an over(Fig. E)

hang (lip extending down) bottom . Even if you have No Overhang, you (Fig. F)

will need to use one (1) 1⁄2” Cabinet Spacer.

2. If your cabinet has an overhang, measure the overhang with a ruler to determine how

many Cabinet Spacers you will need. For example if the measurement is 1” (2.54 cm),

then use three (3) 1⁄2” (1.27 cm) Cabinet Spacers. Use the following guide:

If Overhang 1⁄2” (1.27 cm) 1⁄4” (.64 cm)

Measures Cabinet Spacers Cabinet Spacer

No Overhang 1 None

1⁄2” then use 2 None

3⁄4” then use 2 1

1” then use 3 None

2” then use 4 None

3. With the doors of the cabinet open, use the enclosed template (Fig. C, 8) as a guide to

mark the holes on the underside of the cabinet. If your cabinet has an overhang, slide the

template forward until it touches the inside surface of the over hang. If your cabinet has a

flush bottom, place the template approximately 1⁄4”-1⁄2” (.64 cm-1.27 cm) back from the

front edge of the cabinet.

NOTE: Be sure the Palm Grip Power Scrubber is not set too far back. Hold the unit up

to the underside of the cabinet and confirm that the unit can be easily removed from

the base. Mark the holes through the template onto the underside of the cabinet with

a pencil.

4. Empty the contents from the bottom shelf. Be sure the underside of the cabinet is free of

grease or dirt. Cover the counter top to catch wood chips from drilling.

WARNING: Wear eye protection to prevent injury when working with power and hand

tools.

5. Drill 1/4” (0.64 cm) holes up through the bottom of the cabinet at the hole marks, being

sure to hold the drill vertical.

6. Drop the mounting screws (Fig. C, 1) through the drilled holes from inside the cabinet.

7. You will need (1) 1⁄2” (1.27cm) Cabinet Spacer even if you have a “flush” bottom

cabinet. For cabinets with an overhang, push the proper number of spacers

(see chart) onto the screws coming through the cabinet bottom. You might not use all

the spacers. With the mounting bracket installed in the base, line up the holes with the

exposed screws beneath the cabinet spacers and tighten into the charging base. (Fig. G, 1)

8. Plug the charger into an appropriate electrical outlet being sure the electrical cord can

not be damaged by a heat source or physical abuses such as pinching and rubbing.

Slots are provided in the sides of the charging base to assist in routing of the cord to the

outlet. (Fig. G, 2)

Operation

NOTE: Some accessories may not be included in your model. Refer to product

packaging for contents. Additional accessories are available at local retailers or by

calling, toll-free 1-800-544-6986.

Accessories - Fig. H

1. Tough scour pad (green) for aggressive scrubbing on pots, pans, sinks and other

kitchen surfaces.

2. Scratch free scour pad (white) for non-stick surfaces.

3. Bristle brush for aggressive scrubbing on pots, pans, sinks and other kitchen (blue)

surfaces.

4. Glass brush for cleaning tall narrow glasses, coffee carafes without vacuum insulated

glass liners, blender jars, etc.

Attaching Accessories

Note: Do not attach/remove accessory when unit is running.

1. To connect an attachment, line up the shape of the end of the accessory with the shaft

and push it on, until it snaps in place.

2. To remove an attachment, simply pull it off.

Operation

How to Operate Switch

1. To operate, push the Switch (Fig. A, 3) in to turn on. Press the Switch in again to

turn off. To avoid splatter from a Brush or Pad, turn the scrubber off while the

attachment is still in contact with the surface.

2. Because this scrubber is powerful, you don’t have to apply excessive pressure while

operating. Use a circular motion on large areas.

Tips on Cleaning Agents

IMPORTANT: The palm grip power scrubber has been designed for easy, powerful

cleaning. If you are uncertain about its use on a surface, test an attachment on a

small inconspicuous area before cleaning larger areas.

• Always follow manufacturer’s recommendations when using a chemical cleaner such as

sprays, foams, rub-on gels, liquid detergents, or bleach solutions.

• Cleaners with abrasives can damage some surfaces. Use a cleaner that is appropriate for

the surface being cleaned. Test the cleaner on a small, inconspicuous area if uncertain.

• Always wear rubber gloves and protective eye wear (to avoid splatter) when using irritating

cleaners.

Cleaning and Storage

1. Clean the Brushes and Scrub Pads in a mild detergent, rinse with water and air dry.

You may rinse any attachments/accessories by dipping the scrubber into a bucket of

water no more than 12 inches (30 cm) deep or running under a faucet. Do not leave

immersed for more than 5 minutes.

2. To clean the scrubber unit, wipe with a damp sponge and a mild soap.

3. The drip cup in the charging base can be removed and cleaned with a damp cloth and

a mild soap. (Fig. I)

4. Store the scrubber and attachments/accessories indoors.

Battery Removal and Disposal

This product uses a nickel-cadmium (Ni-Cad) rechargeable and recyclable battery.

When it can no longer be recharged, it should be removed from the unit and recycled.

The battery must not be incinerated or composted. The battery can be taken for disposal to

a Black & Decker Inc.,Company-Owned or Authorized Service center. There are also some

local retailers who are participating in a national recycling program (see “RBRC Seal“).

Call your local retailer for details. If you bring the old battery to a Black & Decker Company

Owned or Authorized Service Center, the Center will arrange for recycling it. Or, if you wish,

contact your local municipality for proper disposal instructions in your city/town.

Battery Removal - Fig. J

1. Remove the three screws from the underside of the unit using a phillips screw driver.

Remove the cap by pulling up as shown. (Fig. J, 1)

2. Loosen the wires out of the notches and slide the switch out. (Fig. J, 2)

3. Disconnect the battery pack terminals. Lift and rotate the motor/battery assembly up out

of the lower housing. (Fig. J, 3)

4. Straighten the battery pack wires to allow it to be slid out of the tool as shown. (Fig. J, 4)

Dispose of the battery as noted above.

Flush Bottom

Superficie nivelada

Sans lambrequin

Overhang Bottom

Inferior saliente

Avec lambrequin

1234

123

Flush Bottom Overhang Bottom

Cabinet

spacers

MODE D’EMPLOI

ÉL

Numéros de catalogue : PKS200, PKS200B

Voici des renseignements importants à connaître :

• Lors de l’immersion de la brosseuse dans l’eau, ne pas couvrir l’appareil

avec plus de 1 mètre (3 pieds) d’eau. Ne pas immerger la brosseuse

pendant plus de 30 minutes.

The RBRC™ Seal

The RBRC™ (Rechargeable Battery Recycling Corporation) Seal on the

nickel-cadmium battery (or battery pack) indicates that the costs to recycle the

battery (or battery pack) at the end of its useful life have already been paid by

Black & Decker. In some areas, it is illegal to place spent nickel-cadmium batteries in the

trash or municipal solid waste stream and the RBRC program provides an environmentally

conscious alternative.

RBRC in cooperation with Black & Decker and other battery users, has established

programs in the United States and Canada to facilitate the collection of spent

nickel-cadmium batteries. Help protect our environment and conserve natural resources by

returning the spent nickel-cadmium battery to an authorized Black & Decker service center

or to your local retailer for recycling. You may also contact your local recycling center for

information on where to drop off the spent battery, or call 1-800-8-BATTERY.

Service Information

Black & Decker offers a full network of company-owned and authorized service locations

throughout North America. All Black & Decker Service Centers are staffed with trained

personnel to provide customers with efficient and reliable power tool service.

Whether you need technical advice, repair, or genuine factory replacement parts, contact

the Black & Decker location nearest you.

To find your local service location, refer to the yellow page directory under "Tools–Electric"

or call: 1-800-54-HOW TO (544-6986) or visit www.blackanddecker.com.

Full Two-Year Home Use Warranty

Black & Decker (U.S.) Inc. warrants this product for two years against any defects in

material or workmanship. The defective product will be replaced or repaired at no charge in

either of two ways:

The first, which will result in exchanges only, is to return the product to the retailer from

whom it was purchased (provided that the store is a participating retailer). Returns should

be made within the time period of the retailer’s policy for exchanges (usually 30 to 90 days

after the sale). Proof of purchase may be required. Please check with the retailer for their

specific return policy regarding returns that are beyond the time set for exchanges.

The second option is to take or send the product (prepaid) to a Black & Decker owned or

authorized Service Center for repair or replacement at our option. Proof of purchase may

be required. Black & Decker owned and authorized service centers are listed under

"Tools–Electric" in the yellow pages of the phone directory.

This warranty does not apply to accessories. This warranty gives you specific legal rights

and you may have other rights which vary from state to state. Should you have any

questions, contact the manager of your nearest Black & Decker Service Center. This prod-

uct is not intended for commercial use.

Free warning label replacement: If your warning labels become illegible or are missing,

call 1-800-544-6986 for a free replacement.

See ‘Tools-Electric’

– Yellow Pages –

for Service & Sales

Black & Decker (U.S.) Inc.,

701 E. Joppa Rd.

Towson, MD 21286 U.S.A.

MÉ

ÉR

-6

D’

’

’A

AVERTISSEMENT : avertissements de sécurité et

directives importantes

Lors de l’utilisation d’appareils électriques, toujours respecter les mesures

de sécurité de base, notamment les suivantes :

LIRE ATTENTIVEMENT ET COMPRENDRE TOUTES LES DIRECTIVES AVANT

D’UTILISER L’APPAREIL.

AVERTISSEMENT : certains produits de nettoyage contiennent des produits

chimiques reconnus par l’État de Californie comme pouvant

causer le cancer, des anomalies congénitales ou d’autres

problèmes liés aux fonctions reproductrices. Lors de

l’utilisation de la brosseuse électrique à prise palmaire,

s’assurer de lire les étiquettes des produits nettoyants et à

rechercher tout avertissement lié à l’article 65. Suivre les

directives mentionnées sur les récipients de tels produits.

AVERTISSEMENT : pour réduire les risques d’incendie, de chocs électriques ou

de blessures :

• Exercer une étroite surveillance pour l’utilisation de tout appareil électrique par des enfants

ou à proximité de ceux-ci. Interdire l’utilisation de l’appareil comme jouet.

• Pour se protéger contre le risque d’électrocution, ne pas immerger le chargeur de pile ou la

base de charge dans l’eau ou autre liquide.

• Ne pas utiliser l’appareil en présence de vapeurs ou de liquides explosifs ou inflammables.

• Toujours porter une protection oculaire lorsque la brosseuse est utilisée avec des

substances irritantes. Utiliser également des gants en caoutchouc, le cas échéant. Lire et

suivre les directives du fabricant à propos du produit nettoyant utilisé. N’utiliser que des

nettoyants domestiques.

• Toujours ranger l’appareil à l’intérieur.

• Éloigner les cheveux, vêtements amples et toutes les parties du corps de tous composants

mobiles.

• Ne pas installer ou retirer d’accessoires/pièces lorsque l’appareil fonctionne.

• Ranger l’appareil hors de la portée des enfants.

• Pour réduire le risque d’incendie ou de choc électrique, ne pas utiliser un appareil

électrique de chauffage sous la base de charge assemblée.

• Ne pas installer la base de charge assemblée au-dessus ou près de toute portion

d’appareil de chauffage ou de cuisinière ou d’un évier ou bassin.

• Ne pas installer l’appareil derrière, sous ou devant le système d’éclairage de l’armoire.

• L’appareil électrique est conçu pour une utilisation domestique seulement et non

commerciale ou industrielle.

• Utiliser l’appareil uniquement selon les indications données dans le présent manuel.

Utiliser uniquement les accessoires recommandés par Black & Decker.

Directives de sécurité importante pour la pile et le

chargeur

• Ne pas charger une pile mouillée ou qui affiche des signes de corrosion.

• Ne pas incinérer la pile. Elle peut exploser dans un feu. Une petite fuite peut se produire

dans la cellule de la pile en cas d’utilisation, de charge ou de conditions de température

extrême(s). Cela n’indique pas de défaillance. Toutefois, si le joint d’étanchéité extérieur est

rompu et que la fuite entre en contact avec la peau : (1) laver immédiatement à l’eau et au

savon ou (2) neutraliser à l’aide d’un acide doux comme du jus de citron ou du vinaigre (3) si

le liquide atteint les yeux, les rincer immédiatement à l’eau claire pendant au moins dix

minutes Consulter un médecin.

REMARQUE : Le liquide est composé d’une solution de 20 % à 35 % d’hydroxyde de

potassium.

• Ne pas utiliser de rallonge. Brancher le chargeur directement dans la prise électrique.

• Le brancher seulement dans une prise électrique standard (120 v, 60 Hz).

• Ne pas utiliser le chargeur avec un autre produit; ni tenter de charger le produit avec un

autre chargeur. Utiliser uniquement le chargeur fourni par le fabricant. (chargeur n°

90500150 ou 90500027)

• Ne pas utiliser le chargeur dans des conditions mouillées ou humide. Il est conçu

uniquement pour une utilisation à l’intérieur. Ne pas utiliser le chargeur près d’éviers ou de

baignoires. Ne pas immerger dans l’eau.

• Ne pas laisser le cordon reposer contre le bord d’une table ou d’un comptoir ou sur une

surface chaude. Installer le chargeur loin d’éviers et de surfaces chaudes.

• Ne pas faire fonctionner le chargeur si la fiche ou le cordon est endommagé; les remplacer

immédiatement.

• Ne pas faire fonctionner le chargeur s’il a reçu un choc violent, s’il est tombé ou s’il a été

endommagé d’une façon ou d’une autre. Retourner l’appareil à tout centre de réparation

autorisé pour évaluation, réparation ou un réglage électrique ou mécanique. Ne pas

démonter le chargeur.

• Pour de meilleurs résultats, ne pas charger la pile si la pile ou la température ambiante est

INFÉRIEURE à 5 °C (40 °F) ou supérieur à 40 °C (105 °F).

• Débrancher le chargeur si non utilisé et avant de le nettoyer ou l’entretenir.

• Ne pas utiliser abusivement le cordon d’alimentation. Pour réduire le risque de dommages à

la fiche ou au cordon d’alimentation, ne jamais transporter le chargeur par le cordon ni tirer

sur le cordon pour le débrancher. Saisir plutôt la fiche et tirer dessus pour débrancher le

chargeur. Éloigner le cordon de la chaleur, de l’huile et des bords tranchants.

CONSERVER CES DIRECTIVES

Mode d’emploi

Avant la première utilisation et conseils pratiques

• La pile n’est pas entièrement chargée lors de son emballage. Charger la pile pour au

moins 16 heures avant la première utilisation. Consulter la rubrique « Charge de la pile ».

Charge de la pile – fig. B

RECHARGE

Les cellules des piles rechargeables neuves du produit doivent être chargées pendant au

moins 16 heures afin d’assurer une puissance maximale. Durant le chargement, le

dispositif peut devenir chaud; ceci est tout à fait normal et ne présente aucun danger. Il peut

être chargé indéfiniment sans danger ni risque de dommages. Il est impossible de «

surcharger » les piles avec le chargeur fourni.

• Placer l’appareil dans la base de charge pour le recharger. Bien éteindre l’appareil et

essuyer toute trace d’humidité avant de le déposer dans la base.

• Le voyant indicateur rouge de la base de charge s’allumera pour indiquer que la pile se

recharge. Il indique que la pile est connectée au chargeur et qu’elle se charge. Le voyant

demeurera rouge tout aussi longtemps que l’appareil est connecté au chargeur.

• Si la pile ne se charge pas correctement :

• s’assurer que l’appareil est éteint et correctement inséré dans la base de charge

et que le voyant de l’indicateur de charge est allumé.

• vérifier le courant à la prise en branchant une lampe ou un autre appareil

électrique pour voir s’il fonctionne;

• vérifier si la prise est reliée à un interrupteur mural qui contrôle le courant;

• déplacer le chargeur et la pile à une température ambiante de 5 à 40 °C (40 à

105 °F).

• NE PAS CONTINUER À UTILISER LA BROSSEUSE À PRISE PALMAIRE avec une pile

épuisée.

Assemblage de la base de charge :

La base de charge de la brosseuse à prise palmaire s’installe de l’une des façons suivantes :

1. installation sur le comptoir

2. installation murale

3. installation sous l’armoire

• Évaluer vos habitudes de travail normales et la possibilité d’ajouter d’autres outils

électriques sous l’armoire.

• S'assurer d'installer la brosseuse électrique à prise palmaire à proximité d'une prise

électrique.

AVERTISSEMENT : importantes mesures de protection à suivre lors

de la sélection de l'emplacement de la base de charge :

• Pour réduire le risque d’incendie ou de choc électrique, ne pas utiliser un appareil électrique

de chauffage sous la base de charge assemblée.

• Ne pas installer la base de charge assemblée au-dessus ou près de toute portion d’appareil

de chauffage ou de cuisinière ou d’un évier ou bassin.

• Ne pas installer l’appareil derrière, sous ou devant le système d’éclairage de l’armoire.

• NE JAMAIS UTILISER DE PETITS CLOUS À TRAVERS OU CONTRE LE CORDON

D’ALIMENTATION POUR LE FIXER.

Quincaillerie pour montage - fig. C

1. 3 vis de montage 4. 1 support de montage

2. 1 cale d’espacement 5. 4 pièces creuses d’ancrage

de 6,3 mm (1/4 po) pour armoire mural

3. 4 cales d’espacement 6. 4 vis d’ancrage

de 12,7 mm (1/2 po) pour armoire 7. 3 capuchons pour vis de montage

8. Gabarit des trous de fixation

Chargeur

Voyant de l’indicateur de charge

Base de charge

Cuvette d’égouttage amovible

Accessoire

Brosseuse

Interrupteur Marche/Arrêt

Specyfikacje produktu

Marka:	Black & Decker
Kategoria:	odkurzacz
Model:	PKS200

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Black & Decker PKS200, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje odkurzacz Black & Decker

Black & Decker VCBD8530 Instrukcja

13 Października 2024

Black & Decker Dustbuster CHV1400 Instrukcja

6 Października 2024

Black & Decker Dustbuster VP302 Instrukcja

5 Października 2024

Black & Decker BLB1401 Instrukcja

4 Października 2024

Black & Decker HV7000 Instrukcja

4 Października 2024

Black & Decker VCBD603 Instrukcja

4 Października 2024

Black & Decker BXVML700E Instrukcja

3 Października 2024

Black & Decker HSVJ415JMBF71 Instrukcja

3 Października 2024

Black & Decker PV1205B Instrukcja

30 Września 2024

Black & Decker REVHV8C Instrukcja

29 Września 2024

Instrukcje odkurzacz

Najnowsze instrukcje dla odkurzacz

Nilfisk BA 551CD Instrukcja

11 Grudnia 2024

Taurus Homeland Ultimate Animal Instrukcja

11 Grudnia 2024

Heinner HVC-MLED700BL Instrukcja

11 Grudnia 2024

Heinner HVC-MC850BL Instrukcja

11 Grudnia 2024

Cecotec Conga Rock Star 3000 matress Instrukcja

11 Grudnia 2024

MetroVac DataVac MDV-1BA Instrukcja

10 Grudnia 2024

MetroVac Vac 'N' Blo HRS-83BA Instrukcja

10 Grudnia 2024

MetroVac MagicAir DIDA-4 Instrukcja

10 Grudnia 2024

ECOVACS Deebot N30 Omni Instrukcja

10 Grudnia 2024

Tower XP10PET Instrukcja

10 Grudnia 2024