Instrukcja obsługi Binatone IDECT iRoam

Binatone Niesklasyfikowane IDECT iRoam

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Binatone IDECT iRoam (2 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 4 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/2
Getting started
Help
General Information
1
2
3
Box Contents
IMPORTANT
Accessory headset only – requires a base unit to operate.
Charger
Power adapter
Headset
Getting started
Step 1. Connecting the charger
• Plug the power adapter pin into the charger.
• Plug the other end of the power adapter into a power outlet.
• Use only the provided power adapter.
TIPS
Do not place your phone in the bathroom or other humid areas.
IMPORTANT
Use only the power adapter supplied with the product.
Step 2. Installing and charging the wireless
headset
• Attach the ear hook to the headset body as indicated. The
ear hook can be attached according to your preference to
wear the headset on the left or right ear.
• Put the installed wireless headset on the base cradle all the
way to the end for ensuring effective charging before using.
When the wireless headset is fully charged, the LED on
headset will light on blue steadily.
Left ear: Right ear:
1
L9_QSG_US_EN_FR_ES.fm Page 1 Friday, July 23, 2010 1:05 PM
IRoam
User Guide
Noise interference on your radio or television
• Your registered base or charger may be too close. Move it
as far away from these objects as possible.
Overview of the Wireless
Headset
1 POWER/TALK ON/OFF
• In idle mode: Press to place a call. Press and hold to
power the wireless headset on or off.
• During a call: Press to end the call.
• During registration: Press to exit the registration
mode.
2 VOLUME UP/FLASH
• During a call: Press to increase the earpiece volume.
Press and hold to answer a second incoming call.
• During ringing: Press to increase the ringer volume.
3 VOLUME DOWN
• During a call: Press to decrease the
earpiece volume.
• During ringing: Press to decrease the ringer volume.
Wireless Headset LED
Indicators
Purple:
Steadily on: The wireless headset is unregistered.
Flashing: The wireless headset is registered but the base is
not available (searching or out of range).
Blue:
Steadily on: When the headset is seated in the base and fully
charged. Once the headset is successfully registered, the blue
light will flash on then off, for about three seconds at a time,
and emit a long beep.
Long flashing: The wireless headset is in idle mode and off
the base.
Double flashing: The wireless headset is on, and if the signal
becomes weak, three short beeps will be heard.
Continuously flashing: The wireless headset is ringing and
can be heard through the earpiece.
Red:
Steadily on: When the wireless headset is charging on the
base.
Long flashing: Indicates that the battery is low, the unit is not
on the base, and the headset will emit short double beeps.
Double flashing: Indicates that the battery is low while the
headset is in use and short double beeps will be emitted.
Triple flashing: Indicates powering on/off the headset and
three short beeps will be emitted through the earpiece.
Red/Blue:
Toggling display: The wireless headset is in registration
mode. When the headset is registered successfully, the
headset will beep for around 2 seconds.
Step 3. Registration
To work as the handset extension, the headset must be
Maximum 5 handsets or headsets can be registered.
• Press and hold FIND for 4 seconds on the base and then
release.
• Press and hold VOL+/FLASH together with VOL - until the
LED on wireless headset toggling between red and blue.
• Place the unregistered wireless headset on the charger.
• A long beep tone is generated and the LED on in blue for a
while if the registration is successful.
Help
Poor audio quality
• The registered base is too close to electrical appliances,
reinforced concrete walls or metal doorframes - move the
base away from any electrical appliances.
No ring tone
• The ring tone is deactivated.
• Increase the volume.
When the headset lost its link with the registered
base during a call
• Check if the power cord is connected properly into the
registered base.
• Check if the power adapter is connected properly into the
wall socket.
• Move the headset closer to the base. It may be out of
range.
• Reset the base by unplugging the unit’s electrical power.
Reset the headset by clicking into the reset hole. Wait for
around 15 seconds and re-plug the power again. Allow up
to one minute for the headset to synchronize with the
registered base again.
Printed in China
Version 1.0
2
L9_QSG_US_EN_FR_ES.fm Page 2 Friday, July 23, 2010 1:05 PM
registered to the base of the listed models on page 2. iDECT
1. Registering to series baseiDECT

Specyfikacje produktu

Marka: Binatone
Kategoria: Niesklasyfikowane
Model: IDECT iRoam

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Binatone IDECT iRoam, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Niesklasyfikowane Binatone

Binatone

Binatone IDECT iRoam Instrukcja

24 Września 2024

Instrukcje Niesklasyfikowane

Najnowsze instrukcje dla Niesklasyfikowane

Black Diamond

Black Diamond BD1121530000ALL1 Instrukcja

15 Października 2024
Husqvarna

Husqvarna K 970 SmartGuard Instrukcja

15 Października 2024
Stihl

Stihl HT 70 Instrukcja

15 Października 2024
Ernesto

Ernesto H14270 Instrukcja

15 Października 2024
Uniden

Uniden BT MIC KIT Instrukcja

15 Października 2024
Vaude

Vaude Omnis Bike 26 Instrukcja

15 Października 2024
ART

ART ProChannel II Instrukcja

15 Października 2024
Aukey

Aukey DR02J Instrukcja

15 Października 2024
Master Lock

Master Lock 653EURD Instrukcja

15 Października 2024
Roland

Roland FR-18 Diatonic Instrukcja

15 Października 2024