Instrukcja obsługi BeamZ S1200 MKII 160.491

BeamZ nóż S1200 MKII 160.491

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla BeamZ S1200 MKII 160.491 (12 stron) w kategorii nóż. Ta instrukcja była pomocna dla 29 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/12

Ref. № 160.491

S MKII 1200

INSTRUCTION MANUAL

GEBRUIKSAANWIJZING

BEDIENUNGSANLEITUNG

V1.2

- 2 -

- 3 -

Warning

- The smokemachine must be placed at least 100 cm away from inammable materials such as curtains,

books, etc. Make sure that the housing cannot be touched by accident.

- For indoor use only.

- During installation, nobody should stand beneath the mounting area.

- Prior to the rst use, have the unit checked by a qualied person.

- The unit contains voltage carrying parts. DO NOT open the smokemachine

- Never plug or unplug the unit with wet hands.

- If the plug and/or mains lead are damaged, they need to be repaired by a qualied technician.

- he unit is damaged to an extent that you can see internal parts, do not plug the unit into a mains If t

outlet. It needs to be repaired by a qualied technician.

- Only connect this unit to an earthed mains outlet of 230Vac/50Hz .

- Always unplug the unit during a thunderstorm or when it is not in use.

- If the unit has not been used for a longer period of time, condensation can occur inside the housing.

Please let the unit reach room temperature prior to use.

- When you unplug the unit from the mains always pull the plug, never the lead.

- In order to prevent dropping of the unit, a safety fastening needs to be installed. This can be a solid

chain, a steel cable, etc. which has to be fastened separately from the mounting bracket.

- The supplied bracket is the main xing and must be used to solidly mount the light eect.

- In order to avoid accidents in public premises, the local legal requirements and safety

regulations/warnings must be fullled.

- Keep out of the reach of children.

Safety

Plug the smoke machine only in an earthed mains outlet or extension cord! ATTENTION: the powercord can

only be replaced by an original replacement, supplied by Tronios. Be careful when lling the fluid tank. First of

all, unplug the mains lead! Then unscrew the cap on the tank and ll it by means of a funnel. Only use the

original Beamz smoke uid which is environmental friendly and, if used correctly, leaves no residues. Do not

obstruct the openings on top of the case to guarantee a good ventilation. The heating element of the smoke

machine generates heat which needs to be removed. Don’t put any objects on the smoke machine.

Installation and Use

Unpack the fog machine. Fill the uid tank by means of a funnel. Plug the unit into a mains outlet. Thus the

heating element is automatically switched on. Depending on the room temperature, it takes about 5 until the

working temperature is reached. Then the thermostat is clicking and the LED on the manual control lights up.

Push the switch once and the smoke machine will produce a nice thick fog. Once the smoke machine has

reached its working temperature (the LED is lit) the smoke machine can produce continuously fog during about

1 minute.

After this period of time, the fog generator is cooled so much down that the thermostat switches o. Wait a few

minutes until the working temperature is reached again. It is recommended to produce smoke with small pauses

in between so that the temperature is maintained and the thermostat doesn’t switch off.

Location

Select a location where it is easy to fill the tank. It is also possible to hang the unit by means of the supplied

holder and xing screws.

Switching the unit o

Switch the unit o by unplugging it from the mains. Otherwise the 1200W heating element will draw

unnecessarily current.

Timer remote control

After some warm-up time, the device is ready for use, the LED will light up on the remote. During use, it may

happen that the machine stops, in this case the LED will go out, indicating that the machine is warming up.

Timer function:

Press the yellow button and set the interval, duration and volume controls to the desired level.

Interval: time between the smoke moments (10-200 seconds)

Volume: amount of smoke (0-100%)

Specyfikacje produktu

Marka:	BeamZ
Kategoria:	nóż
Model:	S1200 MKII 160.491
Kolor produktu:	Szary
Moc:	1200 W
Częstotliwość wejściowa AC:	50 Hz
Napięcie wejściowe AC:	220-240 V
Waga produktu:	5000 g
Długość kabla:	3 m
Zdalnie sterowany:	Tak
Pojemność zbiornika na ciecz:	0.9 l
Pilot zdalnego sterowania:	Przewodowa
Czas ogrzewania:	5 min
Wymiary produktu (SxWxG):	470 x 255 x 200 mm
Płyn operacyjny:	Woda
Wolumen wytwarzania dymu:	215 m³/min