Instrukcja obsługi BeamZ DMX-240

BeamZ Ulga DMX-240

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla BeamZ DMX-240 (48 stron) w kategorii Ulga. Ta instrukcja była pomocna dla 3 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/48
DMX240 Controller
Ref. nr.: 154.090
INSTRUCTION MANUAL
MANUAL DE INSTRUCCIONES
MANUEL D'INSTRUCTIONS
V2.2
2
ENGLISH
Congratulations to the purchase of this Beamz product. Please read this manual thoroughly prior to using the product in order to
benet fully from all features.
Read the manual prior to using the product. Follow the instructions in order not to invalidate the warranty. Take all precautions
to avoid re and/or electrical shock. Repairs must only be carried out by a qualied technician in order to avoid electrical shock.
Keep the manual for future reference.
- Prior to using the product, please ask advice from a
specialist. When the unit is switched on for the rst time,
some smell may occur. This is normal and will disappear
after a while.
- The unit contains voltage carrying parts. Therefore do
NOT open the housing.
- Do not place metal objects or pour liquids into the
product. This may cause electrical shock and
malfunction.
- Do not place the product near heat sources such as
radiators, etc. Do not place the unit on a vibrating
surface. Do not cover the ventilation holes.
- The product is not suitable for continuous use.
- Be careful with the mains lead and do not damage it. A
faulty or damaged mains lead can cause electrical shock
and malfunction.
- When unplugging the product from a mains outlet,
always pull the plug, never the lead.
- Do not plug or unplug the unit with wet hands.
- If the plug and/or the mains lead are damaged, they
need to be replaced by a qualied technician.
- If the product is damaged to such an extent that internal
parts are visible, do NOT plug the unit into a mains outlet
and DO NOT switch the product on. Contact your dealer.
Do NOT connect the product to a rheostat or dimmer.
- To avoid re and shock hazard, do not expose the
product to rain and moisture.
- All repairs should be carried out by a qualied technician
only.
- Connect the product to an earthed mains outlet (220-
240Vac/50Hz) protected by a 10-16A fuse.
- During a thunderstorm or if the product will not be used
for a longer period of time, unplug it from the mains. The
rule is: Unplug it from the mains when not in use.
- If the product has not been used for a longer period of
time, condensation may occur. Let the unit reach room
temperature before you switch it on. Never use the
product in humid rooms or outdoors.
- During operation, the housing becomes very hot. Do not
touch it during operation and immediately after.
- To prevent accidents in companies, you must follow the
applicable guide lines and follow the instructions.
- Secure the product with an extra safety chain if the unit is
ceiling mount. Use a truss system with clamps. Make
sure nobody stands in the mounting area. Mount the
eect at least 50cm away from inammable material and
leave at least 1 meter space on every side to ensure
sucient cooling.
- This product contains high intensity LEDs. Do not look
into the LED light to prevent damage to your eyes.
- Do not repeatedly switch the product on and o. This
shortens the life tim e.
- Keep the unit out of the reach of children. Do not leave
the unit unattended.
- Do not use cleaning sprays to clean switches. The
residues of these sprays cause deposits of dust and
grease. In case of malfunction, always seek advice from
a specialist.
- Only operate the product with clean hands.
- Do not force the controls.
- If the product has fallen, always have it checked by a
qualied technician before you switch the product on
again.
- Do not use chemicals to clean the unit. They damage the
varnish. Only clean the product with a dry cloth.
- Keep away from electronic equipment that may cause
interference.
- Only use original spares for repairs, otherwise serious
damage and/or dangerous radiation may occur.
- Switch the product o prior to unplugging it from the
mains and/or other equipment. Unplug all leads and
cables prior to moving the product.
- Make sure that the mains lead cannot be damaged when
people walk on it. Check the mains lead before every use
for damages and faults!
- The mains voltage is 220-240Vac/50Hz. Check if power
outlet match. If you travel, make sure that the mains
voltage of the country is suitable for this product.
- Keep the original packing material so that you can
transport the product in safe conditions
This mark attracts the attention of the user to high voltages that are present inside the housing and that are of sucient
magnitude to cause a shock hazard.
This mark attracts the attention of the user to important instructions that are contained in the manual and that he should
read and adhere to.
DO NOT LOOK DIRECTLY INTO THE LENS. This can damage your eyes. Persons who are subject to epileptic
attacks should be aware of the eects that this light eect may have on them.
The product has been certied CE. It is prohibited to make any changes to the product. They would invalidate the CE certicate
and their guarantee!
NOTE: To make sure that the unit will function normally, it must be used in rooms with a temperature between 5°C/ °F 41 and
35 95°C/ °F .
Electric products must not be put into household waste. Please bring them to a recycling centre. Ask your local authorities or your
dealer about the way to proceed. The specications are typical. The actual values can slightly change from one unit to the other.
Specications can be changed without prior notice.
prior notice.
Do not attempt to make any repairs yourself. This would invalid your warranty. Do not make any changes to the product. This would also
invalid your warranty. The warranty is not applicable in case of accidents or damages caused by inappropriate use or disrespect of the
warnings contained in this manual. Beamz cannot be held responsible for personal injuries caused by a disrespect of the safety
recommendations and warnings. This is also applicable to all damages in whatever form.
3
UNPACKING INSTRUCTION
CAUTION! Immediately upon receiving the product, carefully unpack the carton, check the contents to ensure that all parts are
present, and have been received in good condition. Notify the shipper immediately and retain packing material for inspection if
any parts appear damage from shipping or the package itself shows signs of mishandling. Save the package and all packing
materials. In the event that the product must be returned to the factory, it is important that the product be returned in the original
factory box and packing.
If the device has been exposed to drastic temperature uctuation (e.g. after transportation), do not switch it on immediately. The
arising condensation water might damage your device. Leave the device switched o until it has reached room temperature.
POWERSUPPLY
On the label on the backside of the product is indicated on this type of power supply must be connected. Check that the mains
voltage corresponds to this, all other voltages than specied, the light eect can be irreparably damaged. The product must also
be directly connected to the mains and may be used. No dimmer or adjustable power supply.
Always connect the device to a protected circuit (circuit breaker or fuse). Make sure the device has an appropriate
electrical ground to avoid the risk of electrocution or re.
DMX-512 CONNECTION
If you are using a standard DMX controller, you can connect the DMX-output of the controller directly to the DMX-input of the
rst unit in a DMX-chain. Always connect the output of one unit with the input of the next unit until all units are connected.
If you use a controller with 5 pin DMX connection you will need to use a 5-pin to 3-pin adapter.
At the last xture, the DMX cable has to
be terminated. Solder a 120 Ohm
resistor between signal (-) and signal (+)
into a 3-pin XLR connector and plug this
into the DMX output of the last xture in
the chain.
3-Pin XLR to 5-Pin XLR Conversion
Conductor
3-Pin XLR
Female
(Out)
Ground/Shield
Pin 1
Data
Compliment (-
signal)
Pin 2
Data True (+
signal)
Pin 3
Not Used
Not Used

Specyfikacje produktu

Marka: BeamZ
Kategoria: Ulga
Model: DMX-240

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z BeamZ DMX-240, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Ulga BeamZ

BeamZ

BeamZ BBP59 Instrukcja

9 Października 2024
BeamZ

BeamZ BBP48 Instrukcja

9 Października 2024
BeamZ

BeamZ LCB144 Instrukcja

8 Października 2024
BeamZ

BeamZ MB30 Instrukcja

7 Października 2024
BeamZ

BeamZ MBW18LED Instrukcja

7 Października 2024
BeamZ

BeamZ StarColor200 Instrukcja

7 Października 2024
BeamZ

BeamZ Panther 60R Instrukcja

7 Października 2024
BeamZ

BeamZ Panther 80 Instrukcja

7 Października 2024
BeamZ

BeamZ LCB246 Instrukcja

7 Października 2024
BeamZ

BeamZ BWA412 Instrukcja

7 Października 2024

Instrukcje Ulga

Najnowsze instrukcje dla Ulga

Goobay

Goobay 30780 Instrukcja

15 Października 2024
QTX

QTX DM-X12 Instrukcja

15 Października 2024
Livarno

Livarno IAN 94799 Instrukcja

15 Października 2024
Astro

Astro Denia Instrukcja

13 Października 2024
AFX

AFX Grace GRCP07CBBK Instrukcja

12 Października 2024
AFX

AFX Point PNTP0107L30D1BK Instrukcja

12 Października 2024
Neewer

Neewer TL97C Instrukcja

9 Października 2024
Neewer

Neewer SRP18C Instrukcja

9 Października 2024
Ikea

Ikea STRÅLA 005.824.56 Instrukcja

9 Października 2024
Ikea

Ikea STRÅLA 705.829.38 Instrukcja

9 Października 2024