Instrukcja obsługi Bauknecht BK7IPA15BM6L0
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Bauknecht BK7IPA15BM6L0 (13 stron) w kategorii zmywarka. Ta instrukcja była pomocna dla 3 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek
Strona 1/13
ENDaily Reference Guide
1
THANK YOU FOR BUYING A BAUKNECHT PRODUCT.
In order to receive a more complete assistance, please
register your appliance on: www.bauknecht.eu/register
FIRST TIME USE
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
Before using the appliance carefully read
Safety and Installation Instructions. More information about your
product available on website: docs.bauknecht.eu
After installation, please remember to remove all transport protection
parts from the dishwasher.
SETTING MENU
1. Switch on the appliance by pressing the button.ON-OFF
2. Hold the Settings (Half Load ) button for 3 seconds, until you hear
a beep and the display shows „SEt”.
3. After one second the rst available setting (letter „h”) will be displayed.
4. Press PREVIOUS /NEXT to scroll through the list of available settings
(see table below), then press START/Pause to view and change the
value of the currently selected setting.
5. Press PREVIOUS /NEXT to change the value, then press START/Pause
to save the new value and return to the main menu.
6. To change another setting, repeat points 4 and 5.
7. Press or wait 30 seconds to exit the menu.ON-OFF
LETTER SETTING VALUES
(Default - )in bold
Water Hardness Level
(see “SETTING THE WATER HARDNESS”
and “WATER HARDNESS TABLE”) 1 | 2 | | 4 | 53
Rinse Aid Level
(see “ADJUSTING THE DOSAGE OF RINSE AID”) 0 | 1 | 2 | 3 | 4 | 5
NaturalDry (see “OPTIONS AND FUNCTIONS”)
“1” = On, “0” = O 1 | 0
Light on the oor (see “OPTIONS AND FUNCTIONS”)
“1” = On, “0” = O 1 | 0
Sound
“1” = On, “0” = O 1 | 0
Factory Settings
Press START/Pause to restore to the factory
default all the values of the settings included
in the settings menu.
-
FILLING THE SALT RESERVOIR
The use of salt prevents the formation of LIMESCALE on the dishes and on
the machine’s functional components.
The salt reservoir is located in the lower part of the dishwasher (under the
lower rack on the left side).
• It is mandatory that the salt reservoir never be empty.
• It is important to set the water hardness.
• Salt must be lled when the SALT REFILL indicator light on the control
panel is lit.
1. Remove the lower rack and unscrew the reservoir cap
(anticlockwise).
2. Position the funnel and ll the salt reservoir (see gure)
right up to its edge (approximately 0,5 kg); it is not un-
usual for a little water to leak out.
3. Only the rst time you do this: ll the salt reservoir
with water.
4. Remove the funnel and wipe any salt residue away from the opening.
Make sure the cap is screwed on tightly so that no detergent can get into
the container during the wash program (this could damage the water
softener beyond repair).
Run a program every time as soon as you completed relling the salt
reservoir to avoid corrosion.
Setting the water hardness
To allow the water softener to work in a perfect way, it is essential that the
water hardness setting is based on the actual water hardness in your house.
This information can be obtained from your local water supplier. The facto-
ry setting is “3”. See „WATER HARDNESS TABLE” .
To change, follow instructions in section “SETTING MENU”.
Only use salt that has been specically designed for dishwashers.
After the salt has been poured into the machine, the SALT REFILL indicator
light switches o.
If the salt container is not lled, the water softener and the heating
element may be damaged as a result of limescale accumulation.
Use of salt is recommended with any type of dishwasher detergent.
WATER SOFTENING SYSTEM
Water softener automatically reduces water hardness, consequently preventing
scale buildup on the heater, contributing also to better cleaning eciency.
This system regenerates itself with salt, therefore it is required to rell
the salt container when empty. The frequency of regeneration depends
on the water hardness level setting - regeneration takes place once per 4-6
Eco cycles with the water hardness level set to . During runs with regenera3-
tion, additional water management system ll will happen. The regeneration
and water management process occurs at the beginning of the cycle with
additional fresh water.
• Single regeneration consumes: ~7.5 of water;
• Takes up to 15 additional minutes for the cycle;
• Consumes below 0.065 kWh of energy.
FILLING THE RINSE AID DISPENSER
Rinse aid makes dish DRYING easier. The rinse aid dispenser should be A
lled when the RINSE AID REFILL indicator light in the control panel is lit.
1. Open the dispenser B by
pressing and pulling up the
tab on the lid.
2. Pour in the rinse aid (max.110
ml), making sure it does not
overow from the dispenser.
If this happens, clean the spill
immediately with a dry cloth.
3. Press the lid down until you hear a click to close it.
NEVER pour the rinse aid directly into the appliance tub.
Adjusting the dosage of rinse aid
If you are not completely satised with the drying results, you can adjust
the quantity of rinse aid used.
To change, follow instructions in the section “SETTING MENU”.
If the rinse aid level is set to ZERO, no rinse aid will be supplied. The LOW
RINSE AID indicator light will not be lit if you run out of rinse aid.
A maximum of levels can be set according to the dishwasher model. 6
• If you see bluish streaks on the dishes, set a low number (0-3).
• If there are drops of water or limescale marks on the dishes, set
a mid-range number (4-5).
FILLING THE DETERGENT DISPENSER
To open the detergent dispenser use the opening device C. Introduce
the detergent into the dry dispenser D only. Place the amount of
detergent for pre-washing directly inside the tub.
1. When measuring out the detergent refer to the
mentioned earlier information to add the proper
quantity. Inside the dispenser , there are indicaD-
tions to help the detergent dosing.
2. Remove detergent residues from the edges of the
dispenser and close the cover until it clicks.
3. Close the lid of the detergent dispenser by pulling
it up until the closing device is secured in place.
The detergent dispenser automatically opens up at the right time accord-
ing to the program. Usage of detergent not designed for dishwashers
may cause malfunction or damage to the appliance.
A
B
D
C
CONTROL PANEL
1. ON-OFF/Reset button with indicator light
2. PREVIOUS program button
3. NEXT program button
4. FAVOURITE button with indicator program
light
5. Salt reservoir empty indicator light
6. Rinse Aid reservoir empty indicator light
7. DESCALE indicator light
8. Closed Water Tap indicator light
9. Display
10. Program number remaining time and indicator
11. PowerClean Pro option button with indicator light
12. Half Load option button with indicator light/ - 3 sec. pressSettings
13. Extra Dry option button with indicator light
14. Delay option button with indicator light
15. START/Pause button with indicator light
Water Hardness Table
Level °dH
German degrees
°fH
French degrees
°Clark
English degrees
1 (soft) 0 - 6 0 - 10 0 - 7
2 (medium) 7 - 11 11 - 20 8 - 14
3 (average) 12 - 16 21 - 29 15 - 20
4 (hard) 17 - 34 30 - 60 21 - 42
5 (very hard) 35 - 50 61 - 90 43 - 62
EN
2
1. CHECK WATER CONNECTION
Check that the dishwasher is connected to the water supply and that
the tap is open.
2. SWITCH ON THE DISHWASHER
Open the door and press the button.ON/OFF
3. LOAD THE RACKS (see LOADING THE RACKS).
4. FILL THE DETERGENT DISPENSER
5. CHOOSE THE PROGRAM AND CUSTOMISE THE CYCLE
Select the most appropriate program in accordance with the type of
crockery and its soiling level (see PROGRAMS DESCRIPTION) by pressing
the buttons.PREVIOUS/NEXT
Select the desired options . Not all (see OPTIONS AND FUNCTIONS)
options are compatible with all programs.
6. START
Start the wash cycle by pressing START/Pause button (led is lit) and
closing the door within 4 sec. When the program starts you hear a single
beep. If the door was not closed within 4sec., the alarm sound will be
played. In this case, open the door, press START/Pause button and close
the door again within 4 sec.
7. END OF WASH CYCLE
The end of the wash cycle is indicated by sound and the display shows
END. Open the door and switch o the appliance by pressing the ON/
OFF button.
Wait for a few minutes before removing the crockery - to avoid burns.
Unload the racks, beginning with the lower one.
MODIFYING A RUNNING PROGRAM
If a wrong program was selected, it is possible to change it, provided
that it has only just begun. the machine: press and hold the RESET
ON/OFF button for more than 3. sec., and the machine will switch o.
The dashboard will show “0:01”. Close the door and wait until drain cycle
ends (around 1 minute). Open the door and switch the machine back on
using the button and select the new wash cycle and any desired ON/OFF
options. Start the cycle by pressing the START/Pause button and closing
the door within 4 sec.
ADDING EXTRA CROCKERY
Without switching o the machine, open the door rst slightly to avoid water
splashing out (START/Pause led starts blinking) (Caution: Hot steam!) and
place the crockery inside the dishwasher. Press the START/Pause button and
close the door within 4 sec., the cycle will resume from the point at which it
was interrupted.
ACCIDENTAL INTERRUPTIONS
If the door is opened during the wash cycle, or if there is a power cut, the
cycle stops. ONLY IF YOU PRESS the START/Pause button and close the
door within 4 sec., the cycle will resume from the point at which it was
interrupted.
WATER MANAGEMENT SYSTEM
This dishwasher allows the storage of up to 3.2 litres of fresh water using
it in the selected programs. Water is stored in a dedicated tank and will be
used in the subsequently selected programs. It is recommended to per-
form the Self-Clean cycle (see PROGRAMS TABLE) periodically.
ADVICE AND TIPS
DAILY USE
TIPS
Before loading the baskets, remove all food residues from the crockery
and
empty the glasses. You do not need to rinse beforehand under running
water.
Arrange the crockery so that it is held in place rmly and does not tip over;
and arrange the containers with the openings facing downwards and the
concave/convex parts placed obliquely, thus allowing the water to reach
every surface and ow freely.
Warning: lids, handles, trays and frying pans should not prevent the spray-
er arms from rotating.
Place any small items in the cutlery basket.
Very soiled dishes and pans should be placed in the lower basket because
in this sector the water sprays are stronger and allow a higher washing per-
formance.
After loading the appliance, make sure that the sprayer arms can rotate
freely.
UNSUITABLE CROCKERY
• Wooden crockery and cutlery.
• Delicately decorated glasses, artistic handicrafts and antique crockery.
Their decorations are not resistant.
• Parts in synthetic material which do not withstand high temperatures.
• Copper and tin crockery.
• Crockery soiled with ash, wax, lubricating grease or ink.
The colours of glass decorations and aluminium/silver pieces can change
and fade during the washing process. Some types of glass (e.g. crystal ob-
jects) can become opaque after a number of wash cycles too.
DAMAGE TO GLASS AND CROCKERY
• Only use glasses and porcelain guaranteed by the manufacturer as dish-
washer safe.
• Use a delicate detergent suitable for crockery
• -Collect glasses and cutlery from the dishwasher as soon as the wash cy
cle is over.
TIPS ON ENERGY SAVING
• When the household dishwasher is used according to the manufacturer’s
instructions, washing tableware in a dishwasher usually consumes
less energy and water than hand dishwashing.
• In order to maximize dishwasher eciency, it is recommended to in-
itiate the wash cycle once the dishwasher is fully loaded. Loading
the household dishwasher up to the capacity indicated by the manu-
facturer will contribute to energy and water savings. Information on
the correct loading of tableware can be found in the Loading chapter.
In case of partial loading, it is recommended to use a dedicated wash op-
tions if available (Half load/ Zone Wash/ Multizone), lling up only select-
ed racks. Incorrect loading or overloading of the dishwasher may increase
resources usage (such as water, energy and time, as well as increase noise
level), reducing cleaning and drying performance.
• Manual pre-rinsing of tableware items leads to increased water and ener-
gy consumption and is not recommended.
HYGIENE
To avoid odour and sediment which can be accumulated in the dishwasher
please run a high-temperature program at least once a month. Use a tea-
spoon of detergent and run it without loading to clean your appliance.
MOVING OR SERVICING THE DISHWASHER
This dishwasher includes a water tank that may remain full of water after
the cycle ends (water can leak out if / when the dishwasher is tipped).
Note: Before servicing or moving the dishwasher, run the Self-Clean cycle to
drain the water tank.
RESISTANCE TO FROST
If the appliance is placed in surroundings exposed to the risk of frost, it must
be drained completely. Run the Self-Clean cycle to drain the water tank.
Turn o the water tap, remove the inlet and outlet hoses, and let all the
water drain away. Make sure that the water softener is full of dissolved
regeneration salt in the salt container, to protect the appliance from tem-
peratures of up to -20°C.
If the appliance was stored in frost conditions the appliance must remain at
an ambient temperature of min. 5°C for before the rst run.at least 24 hours
ENDaily Reference Guide
3
PROGRAMS TABLE
Program Programs description
Drying
phase
NaturalDry
Available options *)
Duration
of wash
program
(h:min)**)
Water
consumption
(litres/cycle)
Energy
consumption
(kWh/cycle)
P1
Eco - Program is suitable to clean normally soiled tablewa-50°
re, that for this use, it is the most ecient program in terms of
its combined energy and water consumption, and that it is used
to assess compliance with the EU Ecodesign legislation. 4:30 9.5 0.55
P2 Auto Intensive - 65° Automatic pro-
gram for heavily soiled dishes and pans. Senses the level of so-
iling on the dishes and
adjusts the program
accordingly. When the
sensor is detecting the
soil level an animation
appears in the display
and the cycle duration
is updated.
2:25-3:10 15.5-24.5 1.30-1.70
P3
Auto Mixed - 55° Automatic program
for normally soiled dishes with dried
food residues. 1:20-3:00 7.5-19.5 0.75-1.20
P4
Auto
Fast
50° - Automatic program for
normally and lightly soiled dishes. The
everyday cycle that ensures optimal
cleaning and drying performance in a
shorter time.
1:00-1:50 7.5-15.5 0.70-1.10
P5
Rapid 45°
- Program is recommended for limited amount of li-
ghtly-soiled dishes with no dried food residues. Does not include
the drying phase.
- 0:30-0:40 10.0-12.0 0.55-0.65
P6
Glass - 45° Program for delicate items, which are more sensitive to
high temperatures, for example, glasses and cups.
1:40-1:50 12.5-16.5 0.95-1.20
P7
Silent - 55° Suitable for night-time operation of the appliance.
Ensures optimal cleaning and drying performance with the
lowest noise emission. 3:50-4:10 10.5-14.5 0.80-1.15
P8
Hygiene - 65° Normally or heavily soiled crockery, with
additional antibacterial wash. Can be used to perform mainte-
nance of the dishwasher. - 1:55-2:10 12.0-19.0 1.40-1.80
P9 Prewash - Used to refresh crockery planned to be washed
later. No detergent is to be used with this program. - 0:12 4.5 0.10
P10
Self Clean - 65° Program to be used to perform maintenance
of the dishwasher and water management system, to be carried
out only when the dishwasher is EMPTY using specic deter-
gents designed for dishwasher maintenance.
-- 1:40 11.0 1.10
ECO program data is measured under laboratory conditions according to European Standard EN 60436:2020.
Note for Test Laboratories: For information on comparative EN testing conditions, please send an email to the following address: dw_test_support@whirlpool.com
Pre-treatment of the dishes is not needed before any of the programs.
*) Not all options can be used simultaneously.
**) Values given for programs other than the program Eco are indicative only. The actual time may vary depending on many factors such as temperature and pressure of the incoming
water, room temperature, amount of detergent, quantity and type of load, load balancing, additional selected options and sensor calibration. The sensor calibration can increase
program duration by up to 20 min.
OPTIONS can be selected/ deselected, after choosing the program, directly by pressing the corresponding button (if available - the indicator lights up) (see
CONTROL PANEL) (see PROGRAMS TABLE). If an option is not compatible with the selected program , the corresponding LED ashes rapidly 3 times and beeps will
sound. The option will not be enabled. An option can change time or water or energy consumption for the program.
OPTIONS AND FUNCTIONS
HALF LOAD - If there are not many dishes to be washed, HALF LOAD
is used to save water, electricity or time, depending on the selected
program. Remember to reduce the amount of detergent.
EXTRA DRY - The higher temperature during the final rinse and the
extended drying phase which allows for improved drying. The EXTRA
DRY option results in the lengthening of the wash cycle.
DELAY - The start of the program may be delayed for a period of time
between and hours.0:30 24
1. Select the program and any desired options. Press the DELAY button
(repeatedly) to delay the start of the program. Adjustable from 0:30 to 24
hours. Once the 24 hours setting is reached, press the DELAY another time
to deactivate the DELAY function.
2. Press the START/Pause button and close the door within 4 sec. the timer
will begin counting down.
3. Once this time has elapsed, the indicator light switches o and the program
begins automatically.
The DELAY function cannot be set once a program has been started.
POWERCLEAN PRO- Thanks to the additional power jets this option
provides a more intensive and powerful wash in the lower rack, in the
specific area. This option is recommended for washing pots and casseroles
(please refer to the PowerClean Pro in loading section).
FAVOURITE PROGRAM The FAVOURITE program may be saved and
will be easily accessible. Find the program using PREVIOUS/NEXT, and
then press the FAVOURITE program button for 3 seconds.
WATER TAP CLOSED – Alarm - Flashes when there is no inlet water or
water tap is closed.
LIGHT ON THE FLOOR - A LED light projected on the oor indicates
that the dishwasher is working. The light goes o at the end of a cycle.
This feature is active by default, but it is possible to deactivate it in the
“SETTINGS MENU”.
NaturalDry - It is a convection drying system which automatically opens
the door during/after the drying phase to ensure exceptional drying
performance every day. The door opens at a temperature that is safe to
your kitchen furniture.
As additional steam protection, specially designed protection foil is added
together with the dishwasher.
To see how to mount protection foil please refer to INSTALLATION GUIDE.
This feature is active by default, but it is possible to deactivate it in the
“SETTINGS MENU”.
DESCALE – Alarm - Limescale accumulation was detected on the
internal components of the appliance. Check if the Water Hardness
Setting salt is at the correct value and is present in the salt container (see
FIRST TIME USE), then (WPro brand is recommended) use a descaling product
with the . After a successful descaling, the icon will stop Self-Clean program
being displayed.
If the actions above are not performed, product performance will deteriorate.
DESCALE warning will start blinking and « » alarm will appear on the dES
display. If still no action is taken, the appliance will only allow a certain
number of cycles to be started (indicated during « » alarm display) dES
and then will be BLOCKED to prevent component damage, with only
the Self-Clean program available. Performing a full descaling will unblock
the product. In the case of extremely high amounts of limescale, descaling
may have to be performed twice to be ecient.
SENSING - When the sensor is detecting the soil level an
animation appears in the display (around 20 min.) and the cycle
duration is updated. is for the level of soiling on the dishes and it SENSING
is present for all cycles (excepting Eco) adjusting the program accordingly.
Specyfikacje produktu
| Marka: | Bauknecht |
| Kategoria: | zmywarka |
| Model: | BK7IPA15BM6L0 |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Bauknecht BK7IPA15BM6L0, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje zmywarka Bauknecht
21 Września 2024
21 Września 2024
20 Czerwca 2024
20 Czerwca 2024
20 Czerwca 2024
20 Czerwca 2024
20 Czerwca 2024
20 Czerwca 2024
20 Czerwca 2024
20 Czerwca 2024
Instrukcje zmywarka
- zmywarka Ikea
- zmywarka Electrolux
- zmywarka DeLonghi
- zmywarka AEG
- zmywarka Balay
- zmywarka Beko
- zmywarka Teka
- zmywarka Smeg
- zmywarka Amica
- zmywarka Gorenje
- zmywarka Etna
- zmywarka Cookology
- zmywarka Russell Hobbs
- zmywarka Bosch
- zmywarka Candy
- zmywarka Whirlpool
- zmywarka Miele
- zmywarka Midea
- zmywarka Baumatic
- zmywarka Hoover
- zmywarka Maytag
- zmywarka GE
- zmywarka Blaupunkt
- zmywarka Brandt
- zmywarka Siemens
- zmywarka Grundig
- zmywarka Haier
- zmywarka Cylinda
- zmywarka Blomberg
- zmywarka Husqvarna
- zmywarka Fisher & Paykel
- zmywarka Indesit
- zmywarka Nodor
- zmywarka Hotpoint
- zmywarka Kenwood
- zmywarka Ariston Thermo
- zmywarka Amana
- zmywarka Hotpoint Ariston
- zmywarka Bomann
- zmywarka CDA
- zmywarka Philco
- zmywarka Neff
- zmywarka Zanussi
- zmywarka Fagor
- zmywarka Thomson
- zmywarka Klarstein
- zmywarka Artusi
- zmywarka KitchenAid
- zmywarka Icecool
- zmywarka Privileg
- zmywarka Arçelik
- zmywarka Hanseatic
- zmywarka Atag
- zmywarka Rosieres
- zmywarka Franke
- zmywarka Inventum
- zmywarka SVAN
- zmywarka AEG-Electrolux
- zmywarka Omega
- zmywarka Comfee
- zmywarka Zerowatt
- zmywarka Respekta
- zmywarka Vedette
- zmywarka JennAir
- zmywarka Frigidaire
- zmywarka Barazza
- zmywarka Electra
- zmywarka Gaggenau
- zmywarka Asko
- zmywarka Daewoo
- zmywarka Ignis
- zmywarka De Dietrich
- zmywarka Eurom
- zmywarka Constructa
- zmywarka Proline
- zmywarka Euromaid
- zmywarka Thermador
- zmywarka Swan
- zmywarka Kluge
- zmywarka Arthur Martin
- zmywarka Logik
- zmywarka Brandy Best
- zmywarka ARC
- zmywarka Dishlex
Najnowsze instrukcje dla zmywarka
12 Października 2024
11 Października 2024
9 Października 2024
26 Września 2024
26 Września 2024
26 Września 2024
26 Września 2024
26 Września 2024
26 Września 2024
26 Września 2024