Instrukcja obsługi Balance RF-WS98

Balance Stacja pogodowa RF-WS98

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Balance RF-WS98 (15 stron) w kategorii Stacja pogodowa. Ta instrukcja była pomocna dla 3 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/15
All-In-One Wireless Professional Weather Station (DCF) (975246) User’s Manual
Functions
-Weather forecast with sunny, partly cloudy, cloudy, rainy and stormy
-Barometric pressure display
-Wind direction display
-Average & gust wind speed with storage of the minimum and maximum measured values
-Daily, weekly, monthly and total rainfall display
-Lightning detection with estimated number of lightning strike and distance display
-Lightning alert indication (Approaching, Departing & Overhead) and alarm setting
-Daily maximum and current UV Index with estimated exposure time display
-Room temperature and interior humidity display with storage of the minimum and maximum
measurement values
-Outside temperature and outside humidity display with storage of the minimum and maximum
measured values
-Dew point, heat index & wind chill display
-Ice/frost alert
-Radio-controlled DCF-77 time signal reception with time display, time-zone setting
-Date display
-Alarm clock with snooze function
In this package you will find:
-One monitor (main unit)
-One Transmitter (Transmits Wind, Rain, UV, Lightning, Temperature/humidity data)
-4 pieces of Nylon straps
-One owner’s’ manual
-Power adapter for the monitor
Additional tools needed for installation
-Small Phillips screwdriver
-Mast, 1 – 1.25 inch (2.54 – 3.18 cm) in diameter (to mount the transmitter)
Installation
Choose a suitable location for your transmitter
-The transmitter must be set up outdoors
-The transmitter must be located within the signal transmission range (100 meters line of sight). Walls and
obstructions reduce the transmission range. Check the signal reception on the weather station before final
assembly.
-Ideally the transmitter should be mounted on a mast or roof of a house, and in an open area where wind,
rain & sunlight can access the transmitter from all sides to enable the wind force, wind direction, rainfall &
UV Index to be measured accurately
-Avoid placing the transmitter close to any electromagnetic radiation sources such as electricity tower or
electrical equipments as the lightning detection will be greatly affected.
-Ensure that the wind vane and the wind wheel are not blocked to guarantee accurate measurements.
-The transmitter should be mounted in an open area where sunlight can shine directly on the UV sensor of
the transmitter any time of the day and is not blocked by tree or wall.
-Do not position under trees or next to walls. The rain must be able to fall on the transmitter without
obstructions to achieve an accurate rainfall measurement.
-Ensure that rain water does not accumulate under the transmitter. It must be able to flow off freely.
Testing the effective transmission range
1) Place the transmitter to your selected outdoor location in horizontal position (see above section) and the
transmitter must be at least 1 meter above ground. (This is not the final assembly and do not permanently
mount the transmitter on a mask or roof at this stage until the effective transmission range is verified)
2) Open the battery door of the transmitter and insert 4 pieces of AA batteries according to the battery polarity
indicated. Close the battery door and tighten the screws.
3) Place the main unit to your selected indoor location. Connect power adapter to the back of the main unit or
insert 3 pieces of AA batteries in the battery compartment.
4) Press [clock/set] button once to skip the initial weather setting
5) The main display will flash indicating it is in the searching mode
(If the main display stops flashing, you may hold the [Search] button for 3 seconds on the main unit to
enforce RF searching)
6) While the main unit is in searching mode, press the [Transmit] button on the bottom of the transmitter to
transmit RF signal to the main unit
7) If they are within the effective transmission range, all the readings including outdoor temperature, humidity,
wind speed, wind direction, rainfall & UVI will display on the main unit.
8) To ensure good RF reception signal, try turning the wind wheel & change the direction of the wind vane on
the transmitter and you should notice the wind speed & direction update within 2 minutes.
If the display reading does not update every minute, the RF reception signal is still poor. Shorten the
transmitter and repeat above transmission range test until you have the display reading updated every 1
minute to ensure good RF reception signal.
9) After testing the effective transmission range, remove all batteries from the transmitter. Remove all
batteries and disconnect the power adapter from the main unit.
Installation and Calibration
1) After verifying the effective transmission range, mount the transmitter on your selected location.
A mast is required with a diameter of approx. 25-3mm (not included) which stands stable and vertical.
Mount the transmitter as shown below with nylon strap provided and it should be at least 1 meter above
ground.
After assembly, ensure that the transmitter must be positioned horizontally to guarantee accurate
measurements for wind speed wind direction, rainfall & UV Index measurements.
2) Open the battery door of the transmitter and insert 4 pieces of AA batteries according to the battery polarity
indicated. Close the battery door and tighten the screws.
3) Connect power adapter to the back of the main unit. Open the battery door and Insert 3 pieces of AA
batteries according to the battery polarity indicated. Close the battery door.
4) The weather forecast display will flash. Press [+] or [-] buttons on to select the current weather condition
as initial weather forecast setup. Press [Clock/Set] to confirm.
5) The main display will flash indicating it is in the searching mode
(If the main display stops flashing, you may hold the [Search] button for 3 seconds on the main unit to
enforce RF searching)
6) While the main unit is in searching mode, Go to the transmitter and keep the wind vane pointing at North
direction and then single press [Transmit] button on the bottom casing to send RF data to the receiver for
registration & calibration purpose (LED will flash few times)

Specyfikacje produktu

Marka: Balance
Kategoria: Stacja pogodowa
Model: RF-WS98

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Balance RF-WS98, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Stacja pogodowa Balance

Balance

Balance RF-WS98 Instrukcja

26 Sierpnia 2024

Instrukcje Stacja pogodowa

Najnowsze instrukcje dla Stacja pogodowa

Steinberg

Steinberg SBS-WS-600 Instrukcja

16 Grudnia 2024
Steinberg

Steinberg SBS-RS-40 Instrukcja

16 Grudnia 2024
EQ-3

EQ-3 WDC 7000 Instrukcja

15 Grudnia 2024
Oregon Scientific

Oregon Scientific Alizé BAR268HGA Instrukcja

15 Grudnia 2024
Sencor

Sencor SWS 260 Instrukcja

14 Grudnia 2024
Emos

Emos E0531 Instrukcja

14 Grudnia 2024
TFA

TFA 30.3034.01 Instrukcja

14 Grudnia 2024
TFA

TFA Weather Boy 35.1159.02 Instrukcja

14 Grudnia 2024
TFA

TFA 35.1078.10 Instrukcja

14 Grudnia 2024
TFA

TFA 35.1089 Instrukcja

14 Grudnia 2024