Instrukcja obsługi Austrian Audio OC818

Austrian Audio Niesklasyfikowane OC818

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Austrian Audio OC818 (5 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/5

OC818 Large-Diaphragm Condenser Microphone

with Multiple Polar Patterns

Owner Manual ’s

Introduction Safety Instructions and

Please read understand, and follow all instructions in this manual ,

before using this product.

This product was made for professional users and we ask you to

follow a few restrictions to guarantee a hassle-free workflow for you,

and to keep the product in perfect working condition:

• Please do not operate this product in other than the

intended use cases.

• Do not use if the product is defective

• Always keep and operate the product in dry and safe place a

• Do not expose it to excessive heat (for example, do not leave

it in your car parked in the sun)

• If you need to bring the product inside from the cold, please

give it time to reach adequate temperature before use

(allowed storage temperature range: -25°C 60°C). to

• Do not operate outside the intended operating temperature range: 0°C 55°C to

• Do not use this product in wet or in humid environment a

• Do not drop

• When used upside down (for example in the OCH8 or OCS8) make sure that a tight fit is

achieved and do not operate it upside down right above personnel

• Only connect the back output of the OC818 to an OCR8 Bluetooth® dongle or the OCC8 mini

XLR cable. Do not connect that output to any other devices

• This product requires a phantom power source of 48V (+/-4V), max draw is 4mA (with OCR8

connected).

• Please keep this product away from small children and persons who are not able to operate

professional audio equipment (some sound technicians with gray pony-tails included)

• If you need to clean the product, do this only with a soft dry cloth

• Please do not use any third-party accessories unless otherwise stated

• Do not disassemble the product, as there are no user-serviceable parts inside (but plenty of

components to mess up)

• The length of the XLR cable must not exceed 30m.

• Do not remove the sticker

Thank you for reading the instructions so far, and thank you for putting your trust in Austrian Audio.

How to Operate the OC : 818

The OC818 requires phantom power, so please make sure that you are supplying it according to P48

(48V +/- 4V). Peak current consumption is below 4 mA (OC818 with OCR8 connected). Almost all

state- -the-art professional mixing consoles, preamps and audio interfaces provide enough power, of

however some battery driven, or older devices may fail to do so!

Setting up the OC818:

For optimum performance, do not cover the grill of the OC818, and always ensure a secure fit in the

OCH8 (holder) or OCS8 (suspension).

Always place your sound source to face our beautiful logo!

If you record in figure-8, then you can also use the rear side. Or if you record in Omnidirectional, then

it does not matter at all. Or if you pick up a Leslie cabinet and are experimenting with the phase-

shifting-effects. But otherwise: Please face the logo!

Adjusting the Polar Pattern:

The OC818 provides 4 default directional characteristics: figure-8, supercardioid, cardioid and

omnidirectional. The 5th setting ( ) • is called “ ”. If you own an OCR8 Bluetooth dongle Preset Mode

you can program your custom pattern to this position. Factory setting (before you change the

pattern by an OCR8) for this position is broad-cardioid without High Pass Filter and Pad Switch –

those are inactive in Preset Mode.

Switch the polar pattern selector to the desired pattern. Please note that the microphone needs a

few seconds to adapt to the new pattern, especially if you switch all the way from figure-8 (left) to

omni (right) or vice versa (this gives any sluggish electrons time to catch up).

High Pass Filter:

The high pass filter is a powerful tool to reduce unwanted low frequencies, like stage noise, handling,

or your Uncle Albert’s singing.

'' ''0 means not active

'' ''40 is a high pass 2nd order filter at 40 Hz

'' ''80 is a high pass 2nd order filter at 80 Hz

'' ''160 is a high pass 1st order filter from 160 Hz to 80 Hz, and a high pass 2

nd order filter below 80 Hz.

Pad Switch:

The Pad switch reduces the sensitivity of the microphone and prevents overloading the microphone

in loud environments.

'' ''0 means not active

'' ''-10 means that the microphone is 10 dB less sensitive

'' ''-20 means that the microphone is 20 dB less sensitive

'' ''-30 means you may need to see an optician, as there is no “ 30” position.-

Note: The -10dB position reduces the bias voltage of the capsule, so the microphone can take 10dB

more input (I am looking at you there, trombone jockey), whereas the -20db Setting reduces the gain

by another 10 dB to protect your mixer preamp from overload.

Dual Mode and PolarDesigner:

The second output on the rear side of the microphone can deliver the signal of the back membrane,

while you get the front capsule from the regular XLR plug.

Just plug in the OCC8 mini XLR cable supplied with your OC818, and

set the polar pattern switch to the position showing the 2 cardioids.

The OC818 will now work in dual mode, with both capsule

membranes being transmitted independently.

In dual mode, you may record the two signals to two tracks and use our PolarDesigner plugin later to

modify the polar pattern in post-production. Polardesigner lets you even choose the polar pattern for

up to five different frequency bands.

Note: Make sure phantom power (P48) is provided to the main (3-pin) XLR output also in dual mode.

The second (rear) output can be operated with or without feeding phantom power.

How to Operate the OCR8 (sold separately):

The OCR8 connects your OC818 microphone to your smart device (Smartphone or

Tablet) via Bluetooth .

Download the App

Download the Austrian Audio App (containing PolarPilot) from the Apple™ App

Store or the Google Play Store. ™ ™

Please make sure that your device is running the latest version of its operating

system.

The minimum requirement at the time of the initial release, is: iOS or Android 5 Also, the ™ 11 ™.

device must support BLE (Bluetooth Low Energy also called Bluetooth LE Bluetooth Smart). or

Current mobile devices are commonly released with hardware and software for Bluetooth Low

Energy, and almost all devices running these operating systems will be compatible.

As the App is using Bluetooth, please ensure that Bluetooth is switched on. Some devices may ask

you to allow the Austrian Audio App access to your location information. This information is used by

the Bluetooth protocol only we are not processing or tracking any kind of personal data. –

Preparing the OC818

Switch the pattern selector to ''•'' (= Preset Mode - all the

way to the right)

Power (to) the OCR8

The OCR8 is powered by the phantom power from the OC818, so please make

sure that you are supplying the OC818 according to P48 (48V +/- 4V).

You may either connect the OC818 to phantom power first, or plug the OCR8

into the OC818 first. Once you have completed both steps, the OCR8 will

automatically switch into pairing mode and the blue LED will flash fast. Now “ ”

it is time to open the Austrian Audio App.

Specyfikacje produktu

Marka:	Austrian Audio
Kategoria:	Niesklasyfikowane
Model:	OC818

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Austrian Audio OC818, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje Niesklasyfikowane Austrian Audio

Austrian Audio OC818 Instrukcja

4 Września 2024

Instrukcje Niesklasyfikowane

Najnowsze instrukcje dla Niesklasyfikowane

Techno Line WL 1035 Instrukcja

4 Grudnia 2024

Techno Line WL 2000 Instrukcja

4 Grudnia 2024

BOYA BY-RF5P Instrukcja

4 Grudnia 2024

PCE -MSR 110 Instrukcja

4 Grudnia 2024

Nitecore BB nano Instrukcja

4 Grudnia 2024

Nitecore NIA007 Instrukcja

4 Grudnia 2024

Nitecore BB Mini Instrukcja

4 Grudnia 2024

Nitecore Camera Cleaning Pen Instrukcja

4 Grudnia 2024

Velleman VTLLAMP17 Instrukcja

4 Grudnia 2024

Velleman VTLAMP8 Instrukcja

4 Grudnia 2024