Instrukcja obsługi Audix ADS48

Audix mikrofon ADS48

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Audix ADS48 (2 stron) w kategorii mikrofon. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/2
ADS48
OVERVIEW
The Audix ADS48 is a wide range UHF antenna distribution system that combines up to
four wireless systems to be able to run o a single pair of antennas and power supply.
The ADS48 has an internal switching power supply which eliminates the need for the
individual DC power supplies normally needed for each receiver. RF signals are internally
amplified in order to compensate for any loss that may result from splitting the signal.
SUPPLIED ACCESSORIES
1 x ADS48 Antenna Distribution Unit with rack mount
2 x Antennas - (see photo A below)
1 x IEC power cable
4 x Power Jumper Cables to provide power to individual receivers - (see photo B below)
8 x BNC-to-BNC Coaxial Cables for pass through connection for up to
4 additional receivers (single or dual) - (see photo C below)
2 x Coaxial cables for front mounting antennas - (see photo D below)
UHF Antenna
Distribution System
SPECIFICATIONS
Frequency Range
470 - 900 MHz
RF Output Level (Gain)
0 dB d + or – 3 dB
Input Impedance
50 Ohm
Output Impedance
50 Ohm
Power Voltage
100 – 240 V AC 50 / 60 Hz
Output DC Voltage
+12 V DC, 800 mA maximum
Antenna Input DC Voltage
8 V, 150 mA maximum
Dimensions
19” (W ) x 2” (H) x 10” (D)
480 mm (W ) x 45 mm (H) x 250 mm (D)
Net Weight
16 oz / 2.15 kg
A B C D
FRONT MOUNTING ANTENNAS (Do this step before installing in rack)
A. Remove the hex nut from the threaded end of the front mount
antenna cable.
B. Insert the end of the front mounting cable through the back side of the
rack hole. Note that the hole is slotted on one side it can only go in one
way. Screw on the hex nut to secure.
C. Attach the antenna cable on the left side to antenna A INPUT and the
cable on the right side of the unit to antenna B INPUT. Install the ADS48 into
the rack. (See B and F below)
ALL SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE.
www.audixusa.com
503.682.6933 Fax: 503.682.7114
Audix Corporation 9400 SW Barber St. Wilsonville, OR 97070
ver 1.1 07-19
PRODUCT REGISTRATION: Please register your product online at www.audixusa.com/docs_12/about/product_registration.shtml.
SERVICE AND WARRANTY:
This microphone is under warranty for a period of 1 year to be free of defects in material and workmanship. In the event of a product failure due to materials or
workmanship, Audix will repair or replace said product at no charge with proof of purchase. Audix does not pay or reimburse shipping costs for warranty repairs or returns. The warranty excludes
any causes other than manufacturing defects, such as normal wear, abuse, environmental damage, shipping damage or failure to use or maintain the product per the supplied instructions. No
Implied Warranties: All implied warranties, including but not limited to implied warranties of merchantability and fitness for a particular purpose are hereby excluded. The liability of Audix, if any,
for damages relating to allegedly defective products shall be limited to the actual price paid by Dealer for such products and shall in no event include incidental or consequential damages of
any kind. Should your microphone fail in any way, please contact the Audix Service department at 503.682.6933. A Return Authorization is required before returning any product. OTHER THAN
THIS WARRANTY, AUDIX MAKES NO WARRANTIES, EXPRESS OR IMPLIED, WITH RESPECT TO THE PRODUCTS, THE USE OF THE PRODUCTS, THE PERFORMANCE OF THE PRODUCTS. AUDIX SHALL
NOT BE LIABLE FOR SPECIAL INCIDENTAL, CONSEQUENTIAL, INDIRECT OR SIMILAR DAMAGES ARISING FROM OR BASED ON THE SALE, USE, STORAGE OR DISPOSAL OF THE PRODUCTS, AUDIX’S
SERVICE WORK, BREACH OF WARRANTY, BREACH OF CONTRACT. NEGLIGENCE, OR ANY OTHER THEORY OF LIABILITY, EVEN IF AUDIX HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
ADS48
SETTING UP THE DISTRIBUTION SYSTEM
BACK OF ADS48
CABLE INSTRUCTION FOR ANTENNA DISTRIBUTION FOR
ADDITIONAL RECEIVERS: All cables are connected from
the back side of the ADS48 to the back side of the
additional receiver(s).
Using the BNC antenna coax cable, connect output Antenna
A #1 from the ADS48 (see E above) to Antenna A on the
Performance Series receiver and Antenna B #1 from the ADS48
(see C above) to Antenna B on the Performance Series receiver.
Additional receivers are done in exactly the same way.
IMPORTANT: Antennas must be hooked up correctly A to A
and B to B to work properly.
A
A B C D E F
B
C
CABLE INSTRUCTION FOR POWER DISTRIBUTION: All cables
are connected from the back side of the ADS48 to the back side of the
additional receiver(s).
Using the power jumper cables plug one side of the cable into DC Output
#1 on the ADS48 (see D above) and the other end to the DCV Input on
the Performance Series receiver. Additional receivers will be done in the
same sequence.
Power Cable: Plug the provided IEC power cable into the back of the ADS48
and then plug into electrical outlet. (see A above)
Power up the ADS48 via the power switch on the front. The light will indicate
that the unit is powered up. The ADS48 acts as the master power unit for all
receivers in the chain. Receivers will not power up without the master power
switch being on.


Specyfikacje produktu

Marka: Audix
Kategoria: mikrofon
Model: ADS48

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Audix ADS48, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje mikrofon Audix

Audix

Audix ADS48 Instrukcja

28 Grudnia 2024
Audix

Audix M63 Instrukcja

8 Października 2024
Audix

Audix M45 Shortgun Instrukcja

8 Października 2024
Audix

Audix M55D Instrukcja

4 Października 2024
Audix

Audix M40 Instrukcja

2 Października 2024
Audix

Audix M55WO Instrukcja

23 Września 2024
Audix

Audix M40W12HC Instrukcja

22 Września 2024
Audix

Audix OM2 Instrukcja

22 Września 2024
Audix

Audix Fireball Instrukcja

22 Września 2024
Audix

Audix M55W Instrukcja

22 Września 2024

Instrukcje mikrofon

Najnowsze instrukcje dla mikrofon