Instrukcja obsługi Audiovox RCR3273R

Audiovox Zdalne sterowanie RCR3273R

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Audiovox RCR3273R (2 stron) w kategorii Zdalne sterowanie. Ta instrukcja była pomocna dla 6 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/2

Battery Saver

Your universal remote control saves battery power by

automatically turning off if any key is pressed for more than

60 seconds. This saves your battery life should your remote

get stuck in a place where the keys remain depressed, such as

between sofa cushions.

RCR3273R /

RCR3373R

Universal Remote Control

Owner’s Manual

Manual del Propietario (parte posterior)

SAVE THIS MANUAL AND THE CODE LISTS!

Remote controls can sometimes lose their programming

when you change the batteries. Make sure you keep the

manual and code lists in a safe place so that you can

reprogram the remote if you need to.

Tip: This remote is already programmed to operate

most RCA-branded TVs, VCRs, DVD players and satellite

receivers. Just press the corresponding key—DVD•VCR

for a DVD player, TV for a television, SAT•CBL•DTC for a

satellite receiver.

Your universal remote requires two AAA alkaline batteries (not

included).

To install the batteries:

1. Remove the battery

compartment cover.

2. Insert the batteries, matching

the batteries to the (+) and

(–) marks inside the battery

compartment.

3. Push the battery cover back into

place.

Battery Precautions:

• Do not mix old and new batteries.

• Do not mix alkaline, standard (carbon-zinc) or

rechargeable (nickel-cadmium) batteries.

• Always remove old, weak or worn-out batteries promptly

and recycle or dispose of them in accordance with Local

and National Regulations.

To use this universal remote with your home entertainment

system, ﬁrst you need to program it to control your devices.

There are four ways you can program the universal remote to

operate your devices:

• The Auto Code Search goes automatically through all the

codes for the device you’re trying to control. It’s the easiest

method, but it can sometimes take longer than some of the

other programming methods.

• The Brand Code Search searches through the codes for

select brands of devices. It’s not as easy as the auto code

search, but it can be faster.

• The Direct Code Entry lets you enter a code from the

accompanying code list for your brand of device. It’s not as

easy as the other methods, but it’s potentially the fastest

method.

• The Manual Code Search lets you manually go through

all the codes for the device you’re trying to control.

Testing the Code for Maximum Functionality

1. Try a variety of the device’s functions with the remote. If

some device features don’t work, go to the next step to try

a different code.

2. Repeat the Auto Code Search Method from the beginning.

When your device turns off, do not stop searching.

Instead, with the unit now off, continue to press the PLAY

key every 5 seconds until the unit turns back on.

3. Once the unit turns back on, press the REVERSE key on the

remote every 2 seconds until your device turns off again.

When your device turns off again, press the STOP key.

4. Test the key’s functionality again by attempting to control

a variety of the device’s functions. If the code that has

been stored controls the majority of the device’s functions,

programming is complete. If the code stored does not give

maximum functionality, try another code.

Auto Code Search

The Auto Code Search goes automatically through all the

codes for the device you’re trying to control. When you nd

the one that operates your device, you can stop the search and

store that code.

TIPS: Each device key is associated with a type of

device—the TV is preset to search for TVs, SAT•CBL•DTC

for satellite receivers, cable boxes or digital TV converters

(DTC), and DVD•VCR for DVD players. To program a device

key for a different type of device (for example, to program

the DVD•VCR key to control a PVR or VCR), see the

Reassigning the DVD•VCR Key to Control a VCR section.

To exit without saving a new code at any point in the Auto

Code Search, press the CLEAR key.

1. Manually turn on the device you

want to control.

2. Press and hold the device key you want to program. While

you’re holding down the device key, use your other hand

to press and hold the remote’s POWER key at the same

time.

3. Wait until the remote’s indicator

comes on and stays on. Then

release both keys.

4. Point the remote directly at the

front panel of the device you

want to control. Press PLAY on

the remote and wait 5 seconds.

The remote is testing a batch of

10 codes on your device.

Did your device turn off?

YES: Go to step 5.

NO: Press PLAY again. The remote tests the next batch of

10 codes.

Keep pressing PLAY every 5 seconds until your device turns

off.

5. When your device turns off, press

the REVERSE key on the remote

and wait at least 2 seconds.

The remote tries the last of the

previous ten codes.

Did your device turn on?

YES: Press the STOP key. You’re

done! You’ve programmed this

device key.

NO: Press REVERSE again. The remote tests the next

code in the batch.

Keep pressing REVERSE every 2 seconds until your device

turns back on. When it does, press STOP.

Note: If you accidentally press the REVERSE key after your

device turns on, press the FORWARD key. Then, wait two

seconds to see if your device turns off again.

NOTES

Throughout the programming of each key, be sure to keep

the remote pointed at the IR sensor of the device you are

currently programming the remote to control.

Test the remote with the device to make sure the

device key is programmed with the correct code for

maximum functionality. If some features don’t work, try

a different code. See the “Testing the Code for Maximum

Functionality” section below for more information.

During the Auto Code Search, the remote ignores

keypresses that aren’t part of the search.

The search times out after two minutes (the indicator blinks

four times and turns off, and the last programmed code

under that device key is retained).

The indicator blinks four times and turns off when the

remote has gone through all the codes. The remote exits

the Auto Code Search. If your device hasn’t turned off yet,

try a different search method.

Testing the Code for Maximum Functionality

1. Try a variety of the device’s functions with the remote. If

some device features don’t work, go to the next step to try

a different code.

2. Repeat the Brand Code Search from the beginning. When

the device turns off for the ﬁrst time, don’t press the STOP

key, which would store the same code. Instead, with the

unit now off, continue to press the POWER key repeatedly

until the unit turns back on.

3. Once the unit turns back on, you have found another code

that operates the device. Press the STOP key.

4. Test the key’s functionality again by attempting to control

a variety of the device’s functions. If the code that has

been stored controls the majority of the device’s functions,

programming is complete. If the code stored does not give

maximum functionality, try another code.

Brand Code Search

The Brand Code Search goes through only the codes for one of

the select brands listed in the accompanying code list. If your

brand of device is listed, this search can be very quick and easy.

TIPS: Each device key is associated with a type of device—

the TV is preset to search for TVs, SAT•CBL•DTC for satellite

receivers, cable boxes or digital TV converters (DTC), and

DVD•VCR for DVD players. To program a device key for

a different type of device (for example, to program the

DVD•VCR key to control a PVR or VCR), see the Reassigning

the DVD•VCR Key to Control a VCR section.

To exit without saving a new code at any point in the Brand

Code Search, press the CLEAR key.

1. Manually turn on the device you

want to control.

3. Press and hold the device key you want to program. While

you’re holding down the device key, use your other hand

to press and hold the remote’s POWER key at the same

time.

4. Wait until the remote’s indicator

comes on and stays on. Then release

both keys.

6. Point the remote directly at the

front panel of the device you want

to control. Press POWER on the

remote and wait 2 seconds. The

remote is testing a single code for

your device’s brand.

Did your device turn off?

YES: Press the STOP key to store the code. You’re done!

You’ve programmed this device key.

NO: Press POWER again. The remote tests the next code

for your brand.

Keep pressing POWER every 2 seconds until your device

turns off. When it does, press STOP.

2. Find your device’s brand in the

Brand Code list section of the

accompanying code list. Circle

the number for your brand and

keep the list handy.

Co d e L is ts

Li s ta de Có di g os

2 3

5 6

789

T V

VCR

2 3

5 6

789

DVD

SAT/CAB LE

2 3

5 6

789

2 3

5 6

789

5. Look at the number you circled for

your device’s brand code number.

Press that number on the remote

keypad.

NOTES

Throughout the programming of each key, be sure to keep

the remote pointed at the IR sensor of the device you are

currently programming the remote to control.

Test the remote with the device to make sure the device

key is programmed with the correct code for maximum

functionality. If some features don’t work, try a different

code. See the “Testing the Code for Maximum Functionality”

section below for more information.

During the Brand Code Search, the remote ignores

keypresses that aren’t part of the search.

The search times out after two minutes (the indicator blinks

four times and turns off, and the last programmed code

under that device key is retained).

The indicator blinks four times and turns off when the

remote has gone through all the codes. The remote exits the

Brand Code Search. If your device hasn’t turned off yet, try a

different search method.

Direct Code Entry

Direct Code Entry lets you enter a code from the accompanying

code list for your brand of device. It’s not as easy as the other

methods, but it’s potentially the fastest method.

TIP: Each device key is associated with a type of device—

the TV is preset to search for TVs, SAT•CBL•DTC for satellite

receivers, cable boxes or digital TV converters (DTC), and

DVD•VCR for DVD players. To program a device key for

a different type of device (for example, to program the

DVD•VCR key to control a PVR or VCR), see the Reassigning

the DVD•VCR Key to Control a VCR section.

1. Manually turn on the device you

want to control.

3. Press and hold the device key you want to program(the

indicator light comes on).

While you’re holding down the device key, use your other

hand enter the ﬁrst ﬁve-digit code for your brand in the

code list (the indicator light goes off after the ﬁrst digit).

2. Find the Code List that came with

the remote. Locate the section for

the type of device you’re trying to

program, and ﬁnd your brand in

that section. Circle the codes for

your brand and keep them handy.

Co d e L is ts

Li s ta de Có di g os

2 3

5 6

789

T V

VCR

2 3

5 6

789

DVD

SAT/CAB LE

2 3

5 6

789

2 3

5 6

789

NOTES

Remember to enter the code for future reference in the box

provided in the Code Retrieval section of this manual.

If your brand isn’t listed in the code list, use one of the Code

Search methods to program the remote control. (Refer to the

Auto and Manual Code Search methods.)

If you release the device key any time during the Direct

Code Entry procedure, the indicator blinks four times, and

the process is exited. The last programmed code under the

device key is retained.

Test the remote with the device to make sure the device

key is programmed with the correct code for maximum

functionality. If some features don’t work, try a different code

in the list.

4. When you’ve nished entering

the ﬁve-digit code, keep holding

down the device key and look at

the indicator light.

Is the indicator light on?

YES: You’re done! You’ve programmed this device key.

NO, it blinked four times and turned off: You have

either entered a code number that is not in the code lists or

missed a step in the code entry procedure. Try step 3 again.

Indicator light

Manual Code Search

The Manual Code Search lets you go one-by-one through all the

codes for the device you’re trying to control. When you nd the

one that operates your device, you can stop the search and store

that code.

TIPS: The Manual Code Search method may take a long time

because the remote searches through all of the codes in

its memory one-by-one. If your brand is listed in the Brand

Codes or the Code Lists, rst try the Brand Code Search or

the Direct Code Entry method.

Each device key is associated with a type of device—the TV is

preset to search for TVs, SAT•CBL•DTC for satellite receivers,

cable boxes or digital TV converters (DTC), and DVD•VCR for

DVD players. To program a device key for a different type of

device (for example, to program the DVD•VCR key to control

a PVR or VCR), see the Reassigning the DVD•VCR Key to

Control a VCR section.

To exit without saving a new code at any point in the Manual

Code Search, press the CLEAR key.

Step 1: Install your batteries

Step 2: Program your remote

In most cases, the keys on

this remote perform the same

functions as the keys on your

original remotes once you’ve

programmed this remote to

operate your components.

Many keys on this remote

have other functions as well.

Device keys ( , TV

SAT•CBL•DTC DVD•VCR, ) put

the remote in the right mode

to control your device.

GUIDE MENU and put the

remote in menu/guide mode,

which makes the CH/VOL

keys serve as arrow keys;

they also access the same

features as the keys on your

original remotes.

CLEAR exits remote

programming; it also

performs the same functions

as on your original remotes.

CH VOL and keys have dual

functions: they can act as

navigation keys in menu

systems as well as channel

and volume controllers

outside the menus.

The and key INPUT — (dash)

has three functions: (1) it

toggles through all the video

sources connected to your

TV; (2) when the remote is

in VCR mode, this button

toggles between VCR and

the TV input; (3) when you’re

entering digital channel

numbers directly, this button

lets you separate the main

channel number from the

sub-channel number.

Actual model may vary from

illustration

Care and Maintenance

• Keep the remote dry. If it gets wet, wipe it dry immediately.

• Use and store the remote only in normal temperature

environments.

• Handle the remote gently and carefully. Don’t drop it.

• Keep the remote away from dust and dirt.

• Wipe the remote with a damp cloth occasionally to keep it

looking new.

• Modifying or tampering with the remote’s internal devices can

cause malfunction and invalidate its warranty.

1. Manually turn on the device you

want to control.

2. Press and hold the device key you want to program. While

you’re holding down the device key, use your other hand

to press and hold the remote’s POWER key at the same

time.

3. Wait until the remote’s indicator

comes on and stays on. Then release

both keys.

4. Point the remote directly at the front panel of the device you

want to control. Press POWER on the remote and wait 2

seconds. The remote is testing a single code for your device.

Did your device turn off?

Press the STOP key to store YES:

the code. You’re done! You’ve

programmed this device key.

NO: Press POWER again. The

remote tests the next code for

your device.

Keep pressing POWER every 2

seconds until your device turns off.

When it does, press STOP.

TIP: Because there are so many codes, you may have to press

the POWER key many times—possibly hundreds of times.

NOTES

Throughout the programming of each key, keep the remote

pointed at the IR sensor of the device you are programming

the remote to control.

Test the remote with the device to make sure the device

key is programmed with the correct code for maximum

functionality. If some features don’t work, try a different

code. See the “Testing the Code for Maximum Functionality”

section below for more information.

During the Manual Code Search, the remote ignores

keypresses that aren’t part of the search.

The search times out after two minutes (the indicator blinks

four times and turns off, and the last programmed code

under that device key is retained).

The indicator blinks four times and turns off when the

remote has gone through all the codes. The remote exits the

Brand Code Search. If your device hasn’t turned off yet, try a

different search method.

Testing the Code for Maximum Functionality

1. Try a variety of the device’s functions with the remote. If

some features of your devices don’t work, go to the next

step to try a different code.

2. Repeat the Manual Code Search and Entry Method from

the beginning. When the device turns off for the rst time,

don’t press the STOP key, which would store the same

code. Instead, with the unit now off, continue to press the

POWER key repeatedly until the unit turns back on.

3. Once the unit turns back on, you have found another code

that operates the device. Press the STOP key.

4. Test the key’s functionality again by trying a variety of

functions. If the code controls the majority of the device’s

functions, programming is complete. If the code stored

does not give maximum functionality, try another code.

Reassigning the DVD•VCR Key to Control

a VCR

The DVD•VCR key defaults to control a DVD player. If you want

the DVD•VCR key to control a VCR, you must reassign it.

1. Press and hold the DVD•VCR key. The indicator turns on.

Keep holding down the DVD•VCR key.

2. While holding down the DVD•VCR key, press and release

the number 2 key on the keypad. The indicator turns off.

3. Release the DVD•VCR key. The indicator blinks four times and

then turns off. The DVD•VCR key is now set to control a VCR.

4. Follow the directions in the auto, brand, direct entry, or

manual code search to program the DVD•VCR key for your

VCR.

Code Retrieval

Once you’ve programmed the remote to control your devices,

you may want to record the codes for future reference. If

you used the Direct Code Entry method, this is easy. Just

ﬁnd the codes you entered and make a note of them in the

boxes below. If you used one of the Code Search methods to

program your remote or if you used the Direct Entry method

but don’t remember the code, you will need to retrieve each

device’s ﬁve-digit code. Retrieving the actual code and writing

it down will save you time if you ever need to program the

remote again (e.g., if programming is lost when you change

the batteries). If the codes are recorded, you can use the

Direct Entry method to reprogram your remote to control your

devices, which is quick and easy.

1. Press and hold the device key

(TV, SAT•CBL•DTC, DVD•VCR)

whose code you wish to retrieve.

The indicator turns on. Keep

pressing the device key.

2. While holding the device key down, press and hold the

INFO key. The indicator turns off. After holding down both

keys for three seconds, the indicator turns back on.

3. Release both keys. The indicator remains on.

4. Starting with the number 1 key, press and release each

number key on the keypad in the following order: 1-9, then

0. The number that causes the indicator to blink is the ﬁrst

number of the code. As you ﬁnd each number of the code,

write it down for future reference.

Note: All TV codes begin with the number 1; all VCR and DVR

codes begin with the number 2; all DVDs, the number 3; and

all satellite receivers, digital TV converters and cable boxes,

the number 5.

5. Repeat step 4 until you have retrieved all ﬁve numbers in

the code. After the ﬁfth number is retrieved, the indicator

blinks brieﬂy, then turns off.

TIP: To exit the Code Retrieval Mode at any time, press the

CLEAR key.

Note: If you press an invalid key during the Code Retrieval

process, the remote will not respond. If you do not press a

valid Code Retrieval key (TV, SAT•CBL•DTC, DVD•VCR, INFO,

CLEAR), Code Retrieval times out after 15 seconds. The

indicator blinks four times, and then turns off.

IMPORTANT

Because this remote controls more than one device, you

must rst “tell” the remote which device you wish to

operate. That means, if you wish to operate your TV, you

must rst press the TV key to put the remote in the TV

Mode. The remote stays in that device mode until you press

a different device key. For example, if your remote is in TV

Mode and you want to operate the DVD player, you must

press the DVD•VCR key to change device modes.

Accessing Device Menus and Guides

Many devices use on-screen menus and guides to help you

navigate through all their features and programming. While

this remote may not access every menu or guide system

of every device model, it does offer some menu and guide

functionality.

To use a device’s on-screen menu or guide system, you ﬁrst

have to put the remote in Menu or Guide Mode.

1. Make sure your devices are turned on and your TV is set

to the correct device input (use the INPUT key to toggle

through inputs when in TV Mode.)

2. Press the device key whose menu you want to access.

4. Use the VOL+/- and CH+/- keys to

navigate through the on-screen

menu system or guide. To select the

highlighted item, press the OK key.

TIP: If the remote doesn’t respond, check

to see that the indicator is still blinking.

The indicator times out after 20 seconds.

If this happens, just press the MENU or

GUIDE key again, and then retry your

selection.

Exiting Menu/Guide Mode

The remote automatically times out of Menu or Guide Mode

after 20 seconds of inactivity (no keys being pressed). At that

time, the remote clears the displayed menu from the TV.

If you want to exit the Menu Mode yourself, press the

corresponding device key on the remote (TV, SAT•CBL•DTC,

DVD•VCR). The indicator turns off.

Problem: The remote does not operate your device.

• Make sure the remote is in the correct mode by pressing the

corresponding device key (TV, SAT•CBL•DTC, DVD•VCR). This

tells the remote which device to operate.

• Remove any obstacles between the remote and the device. Make

sure you’re aiming the remote at the device’s IR sensor.

• Make sure the batteries are fresh and are properly installed.

Replace the batteries with two new AAA batteries, if necessary

(see the Battery Installation section).

Problem: The remote can’t be programmed to operate your

device.

• If you are testing the remote while programming it, you may be

too far away from the device or at a wrong angle. There must be

an unobstructed path between the remote and the IR sensor on

the device. Move closer and make sure you point the remote at the

device you’re trying to control.

• If you’re using the Direct Entry programming method to enter

the codes for your brand and the unit is still not functioning

properly, try the auto, brand, or manual search method.

• To control combo units, like TV/VCRs or TV/DVDs, you must

program the individual corresponding device keys to control

each part of the combo unit. Once programmed successfully, the

TV key controls the TV functions, and the DVD•VCR key controls

the VCR or DVD functions.

• Make sure the batteries are fresh and are properly installed.

Problem: The remote doesn’t perform commands properly.

• Make sure the remote is in the correct mode by pressing the

corresponding device key (TV, SAT•CBL•DTC, DVD•VCR). This

tells the remote which device to operate.

• Make sure device is ready (for example, the DVD player has a

disc loaded).

• You may have pressed an invalid key for the mode the remote is in.

• If you’re trying to enter a channel number directly, try pressing

the ENTER key after entering the channel number as this is a

requirement of certain models and brands.

• There is a possibility that a programmed code may only be

able to control some of your device features (for example, only

turns a device on and off). To conﬁrm that the device key is

programmed with the correct code for maximum functionality,

test the device. Attempt to control a variety of the device’s

functions with the remote. If some of the features of your

devices don’t work, try programming the remote with a different

code in the list using the Direct Code Entry Method, until you

ﬁnd the code that allows the remote to control the majority of

your device’s functions. Different codes can provide different

levels of functionality.

Problem: The indicator does not light when you press a key.

• You may have pressed an invalid key for the mode the remote is

in.

• Make sure the remote is in the correct mode by pressing the

corresponding device key (TV, SAT•CBL•DTC, DVD•VCR). This

tells the remote which device to operate.

• Make sure the batteries are fresh and are properly installed.

Replace the batteries with two new AAA batteries, if necessary

(see the Battery Installation section).

Problem: The remote will not change channels on device.

• Make sure the remote is in the correct mode by pressing the

corresponding device key (TV, SAT•CBL•DTC, DVD•VCR). This

tells the remote which device to operate.

• Press the ENTER key after you enter a channel number.

• Remove any obstacles between the remote and the device. Make

sure to aim the remote at the IR sensor on the device.

Problem: The device’s menu does not appear on the TV screen.

• Make sure you have connected the device to your TV properly and

selected the correct input. (See your devices’ Owner’s Manuals for

proper connection procedures.)

• Make sure the remote is in the correct mode by pressing the

corresponding device key (TV, SAT•CBL•DTC, DVD•VCR). This

tells the remote which device to operate.

• Menu access isn’t supported for all brands. You may need to use

your original remote control to access menu functions for some

devices.

For more information, please visit www.rcaaccessories.com

Audiovox Electronics Corporation (the “Company”) warrants to you the

original retail purchaser of this product that should it, under normal use

and conditions, be proven defective in material or workmanship during

its lifetime while you own it, such defect(s) will be repaired or replaced

(at the Company’s option) without charge for parts and repair labor. To

obtain repair or replacement within the terms of this Warranty, the product

is to be delivered with proof of warranty coverage (e.g. dated bill of sale),

speciﬁcation of defect(s), transportation prepaid, to the Company at the

address shown below.

This Warranty does not cover product purchased, serviced or used outside

the United States or Canada. This Warranty is not transferable and does

not extend to costs incurred for installation, removal or reinstallation of

the product. This Warranty does not apply if in the Company’s opinion,

the product has been damaged through alteration, improper installation,

mishandling, misuse, neglect, accident, or the simultaneous use of different

battery types (e.g. alkaline, standard or rechargeable).

THE EXTENT OF THE COMPANY’S LIABILITY UNDER THIS WARRANTY IS

LIMITED TO THE REPAIR OR REPLACEMENT PROVIDED ABOVE AND, IN NO

EVENT, SHALL THE COMPANY’S LIABILITY EXCEED THE PURCHASE PRICE

PAID BY PURCHASER FOR THE PRODUCT.

This Warranty is in lieu of all other express warranties or liabilities. ANY

IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF

MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE SHALL

BE LIMITED TO DURATION OF THIS WARRANTY. IN NO CASE SHALL

THE COMPANY BE LIABLE FOR ANY CONSEQUENTIAL OR INCIDENTAL

DAMAGES WHATSOEVER. No person or representative is authorized

to assume for the Company any liability other than expressed herein in

connection with the sale of this product.

Some states/provinces do not allow limitations on how long an implied

warranty lasts or the exclusion or limitation of incidental or consequential

damage so the above limitations or exclusions may not apply to you. This

Warranty gives you specic legal rights and you may also have other rights,

which vary from state/province to state/province.

U.S.A.: Audiovox Electronics Corporation, 150 Marcus Blvd., Hauppauge,

New York 11788

CANADA: Audiovox Return Center, c/o Genco, 6685 Kennedy Road,

Unit 3, Door 16, Mississauga, Ontario L5T 3A5

Trademark(s) ® Registered

RCR3273R US 06 RCR3373R US 06

111 Congressional Blvd., Suite 350

Carmel, IN 46032

Tour of the Remote

Advanced Functions

Troubleshooting

Limited Lifetime Warranty

DVD•VCR CoDe

SAT•CBL•DTC CoDe

TV CoDe

SAT CABLE DTV CONVERT ER

DVD VCR

3. To access menus, press the MENU key. To access guides,

press the GUIDE key. The indicator starts blinking,

indicating you are in Menu or Guide Mode.

Indicator

Specyfikacje produktu

Marka:	Audiovox
Kategoria:	Zdalne sterowanie
Model:	RCR3273R

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Audiovox RCR3273R, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje Zdalne sterowanie Audiovox

Audiovox RCRN03BR Instrukcja

1 Października 2024

Audiovox RCR4258R Instrukcja

1 Października 2024

Audiovox RCRN04GR Instrukcja

1 Października 2024

Audiovox PRO-PDL-25 Instrukcja

1 Października 2024

Audiovox Code Alarm ASCLBTLR Carlink Instrukcja

1 Października 2024

Audiovox RCRV06GR Instrukcja

1 Października 2024

Audiovox PRO-PDL-45 Instrukcja

1 Października 2024

Audiovox RCR3273R Instrukcja

1 Października 2024

Audiovox Code Alarm ASCL6 CarLink Instrukcja

1 Października 2024

Audiovox DA-1 Instrukcja

1 Października 2024

Instrukcje Zdalne sterowanie

Najnowsze instrukcje dla Zdalne sterowanie

Neewer RT112 Instrukcja

9 Października 2024

Neewer RT113 Instrukcja

9 Października 2024

Zalman ZM-VE350 Instrukcja

9 Października 2024

Canon BG-R20 Instrukcja

9 Października 2024

Canon BG-R20EP Instrukcja

9 Października 2024

Mosconi DSP6T8 Instrukcja

8 Października 2024

Mosconi RC MINI Instrukcja

8 Października 2024

Ridem CRC UNB Instrukcja

8 Października 2024

Ridem CRC UNW Instrukcja

8 Października 2024

ORNO OR-GB-458 Instrukcja

8 Października 2024