Instrukcja obsługi Audio-Technica PRO47T


Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Audio-Technica PRO47T (2 stron) w kategorii mikrofon. Ta instrukcja była pomocna dla 7 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/2
propoint® microphones
Cardioid Condenser Thread-Mount Gooseneck Microphones
PRO 47T & PRO 47TL
Features
Direct mounts to any 5/8"- 27 stand, or to included threaded
mounting stud
Wide-range condenser element with low-mass diaphragm for
superior performance
Cardioid polar pattern with 120º acceptance angle
Self-contained electronics eliminate need for external
power modules
Flat, smooth frequency response
Quiet, xed-placement, long-life gooseneck
Foam windscreen offers resistance to P-pops and other
breath blasts
3.0 m (9.8') cable permanently attached between microphone
and XLRM-type connector
Description
The PRO 47T is a wide-range condenser microphone with a cardioid polar
pattern. It is designed to provide clear, intelligible sound reproduction in
a wide range of settings, such as conferences, courtrooms, houses of
worship and other demanding sound pickup applications.
The small-diameter double gooseneck design permits highly exible
positioning while maintaining a smooth, well-contoured appearance. The
PRO 47T stands 315.0 mm (12.40") from the table or podium; it is also
available in a 401.0 mm (15.79") version as PRO 47TL. The two models are
identical in all other respects.
The microphone requires 9V to 52V phantom power for operation.
The microphone's cardioid polar pattern provides a 120° angle of
acceptance.
The microphone includes a 3 m (9.8') permanently attached cable with
an XLRM-type connector, which allows it to be plugged directly into an
XLRF-type jack or cable connector.
The microphone comes equipped with a foam windscreen and a 5/ "- 27 8
threaded mounting stud for securing the microphone to a permanent
mounting surface. The microphone is enclosed in a rugged housing with
a low-reectance black nish.
Operation and Maintenance
The PRO 47T requires 9V to 52V phantom power for operation.
Output low impedance (Lo-Z) balanced. The signal appears across Pins
2 and 3; Pin 1 is ground (shield). Output phase is “Pin 2 hot”— positive
acoustic pressure produces positive voltage at Pin 2.
The provided foam windscreen simply slips over the head of the
microphone, effectively reducing wind noise or popping.
Avoid leaving the microphone in the open sun or in areas where
temperatures exceed 11 F (43° C) for extended periods. Extremely high
humidity should also be avoided.
Architects and Engineers Specications
The microphone shall be a xed-charge condenser designed for permanent
installation or portable applications. It shall have a cardioid polar pattern
with a uniform 120° angle of acceptance and a frequency response of
70 Hz to 16,000 Hz. The microphone shall operate from an external 9V
to 52V DC phantom power source. It shall be capable of handling sound
input levels up to 134 dB with a dynamic range of 106 dB. Nominal open-
circuit output voltage shall be 14.1 mV at 1V, 1 Pascal. Output shall be low
impedance balanced (100 ohms).
The microphone shall have a 3 m (9.8') permanently attached miniature
cable terminating in an XLRM-type connector.
A 5/ "- 27 threaded stud shall be provided for permanent installation to a 8
mounting surface. A foam windscreen shall also be included.
The microphone shall be a small-diameter alternating gooseneck design,
with an overall length of 315.0 mm (12.40") [401.0 mm (15.79")] and a
head diameter of 12.0 mm (0.47"). Weight shall be 63 grams (2.2 oz) [67
grams (2.4 oz)]. Finish shall be low-reectance black.
The Audio-Technica PRO 47T [PRO 47TL] is specied.
PRO 47T & PRO 47TL
Audio-Technica U.S., Inc., 1221 Commerce Drive, Stow, Ohio 44224
Audio-Technica Limited, Old Lane, Leeds LS11 8AG England
©2010 Audio-Technica U.S., Inc. audio-technica.com 0001-0133-01
Specications
In the interest of standards development, A.T.U.S. offers full
details on its test methods to other industry
professionals on request.
1 Pascal = 10 dynes/cm2 = 10 microbars = 94 dB SPL
1 Typical, A-weighted, using Audio Precision System One.
Specications are subject to change without notice.
Fixed-charge back plate, permanently
polarized condenser
Cardioid
70-16,000 Hz
–37 dB (14.1 mV) re 1V at 1 Pa
100 ohms
134 dB SPL, 1 kHz at 1% T.H.D.
106 dB, 1 kHz at Max SPL
66 dB, 1 kHz at 1 Pa
9-52V DC, 2 mA typical
PRO 47T: 63 g (2.2 oz)
PRO 47TL: 67 g (2.4 oz)
PRO 47T: 315.0 mm (12.40") long,
12.0 mm (0.47") head diameter
PRO 47TL: 401.0 mm (15.79") long,
12.0 mm (0.47") head diameter
3-pin XLRM-type on cable
3.0 m (9.8') cable permanently attached
between microphone and XLRM-type
connector
M22
AT8146 windscreen; AT8425 5/8"-27
threaded mounting stud
Element
Polar pattern
Frequency response
Open circuit sensitivity
Impedance
Maximum input sound level
Dynamic range (typical)
Signal-to-noise ratio1
Phantom power requirements
Weight
Dimensions
Output connector
Cable
Audio-Technica case style
Accessories furnished
LEGEND
200 Hz
1 kHz
5 kHz
8 kHzSCALE IS 5 DECIBELS PER DIVISION
240˚
180˚
210˚
270˚
300˚
330˚
150˚
120˚
90˚
30˚
60˚
12" or more on axisLEGEND
Frequency in Hertz
Response in dB
10 dB
100
50 200 10k5k1k500 2k 20k
frequency response: 7016,000 Hz
polar pattern
PRO 47T PRO 47TL
287


Specyfikacje produktu

Marka: Audio-Technica
Kategoria: mikrofon
Model: PRO47T

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Audio-Technica PRO47T, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje mikrofon Audio-Technica

Instrukcje mikrofon

Najnowsze instrukcje dla mikrofon

Countryman

Countryman B6 Instrukcja

15 Stycznia 2025
Pyle

Pyle PMKSHUSB04 Instrukcja

15 Stycznia 2025
DJI

DJI Mic Mini Instrukcja

15 Stycznia 2025
Vonyx

Vonyx CMS320B Instrukcja

15 Stycznia 2025
BOYA

BOYA BY-PM700 Instrukcja

14 Stycznia 2025
HyperX

HyperX QuadCast S Instrukcja

12 Stycznia 2025
Schertler

Schertler STAT-C Instrukcja

11 Stycznia 2025
Shure

Shure SBC210LM Instrukcja

10 Stycznia 2025
AKG

AKG GN50 M Instrukcja

10 Stycznia 2025