Instrukcja obsługi Audio-Technica ATW-1101
Audio-Technica
mikrofon
ATW-1101
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Audio-Technica ATW-1101 (8 stron) w kategorii mikrofon. Ta instrukcja była pomocna dla 4 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek
Strona 1/8

System 10
Digital Wireless System
Installation and Operation
ATW-1101
UniPak® Transmitter System
ATW-1101/G
Guitar System
ATW-1101/H
Headworn Microphone System
ATW-1101/H92
Miniature Headworn Microphone System
ATW-1101/H92-TH
Miniature (beige) Headworn Microphone System
ATW-1101/L
Lavalier Microphone System
ATW-1102
Handheld Microphone System

System 10 Installation and Operation
2
Notice to individuals with implanted cardiac pacemakers or AICD
devices: Any source of RF (radio frequency) energy may interfere with
normal functioning of the implanted device. All wireless microphones
have low-power transmitters (less than 0.05 watts output) which are
unlikely to cause difculty, especially if they are at least a few inches
away. However, since a “body-pack” mic transmitter typically is placed
against the body, we suggest attaching it at the belt, rather than in
a shirt pocket where it may be immediately adjacent to the medical
device. Note also that any medical-device disruption will cease when
the RF transmitting source is turned off. Please contact your physician
or medical-device provider if you have any questions, or experience any
problems with the use of this or any other RF equipment.
Important Safety Instructions
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with a dry cloth.
7. Install in accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat
registers, stoves, or other apparatus (including ampliers) that
produce heat.
9. Unplug this apparatus during lightning storms or when unused for
long periods of time.
10. Refer all servicing to qualied service personnel. Servicing is
required when the apparatus has been damaged in any way, such as
power-supply cord or plug is damaged, liquid has been spilled or
objects have fallen into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate normally, or has
been dropped.
Thank you for choosing an Audio-Technica professional wireless
system. You have joined thousands of other satised customers who
have chosen our products because of their quality, performance and
reliability. This wireless microphone system is the successful result of
years of design and manufacturing experience.
Audio-Technica’s System 10 is an eight-channel digital wireless system
designed to provide rock-solid performance along with easy setup
and clear, natural sound quality. Featuring stackable, contemporary
styling, System 10 is available in handheld, headworn, guitar, lavalier
and body-pack congurations. Operating in the 2.4 GHz range, far from
TV and DTV interference, System 10 offers extremely easy operation
and instantaneous channel selection. Up to eight channels may be
used together without any frequency coordination problems or group
selection issues.
System 10 wireless ensures clear communications by providing three
levels of diversity assurance: frequency, time, and space. Frequency
Diversity sends the signal on two dynamically allocated frequencies
for interference-free communication. Time Diversity sends the signal
in multiple time slots to maximize immunity to multipath interference.
Finally, Space Diversity uses two antennas on each transmitter and
receiver to maximize signal integrity.
Each System 10 professional digital wireless system includes a
receiver and either a body-pack transmitter or a handheld microphone/
transmitter. ATW-1101 UniPak® body-pack transmitter systems include
models pre-packaged with either an AT-GcW guitar cable (/G), a
PRO 8HEcW headworn microphone (/H), a PRO 92cW headworn
microphone (/H92), a PRO 92cW-TH headworn microphone (/H92-
TH), or an MT830cW lavalier mic (/L) for particular applications. All A-T
Wireless Essentials® microphones and cables, available separately, are
pre-terminated for use with any ATW-1101 system.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO
NOT REMOVE SCREWS. NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO
NOT EXPOSE THE APPLIANCE TO RAIN OR MOISTURE.
CERTIFICATION: THIS DEVICE COMPLIES WITH PART 15 OF THE FCC
RULES. THIS DEVICE COMPLIES WITH INDUSTRY CANADA LICENSE-
EXEMPT RSS STANDARD(S). OPERATION IS SUBJECT TO THE
FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE
HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY
INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY
CAUSE UNDESIRED OPERATION.
Cet appareil est conforme à la/aux norme(s) RSS exempte(s) de licence
d’Industrie Canada. Son fonctionnement est soumis aux deux conditions
suivantes : (1) cet appareil ne doit pas causer d’interférence et (2)
cet appareil doit accepter toutes les interférences, y compris celles
susceptibles de provoquer un fonctionnement non souhaité.
WARNING: Changes or modications not expressly approved in writing
by Audio-Technica may void the user’s authority to operate
this equipment.
RF Exposure Statement: This transmitter must not be co-located or
operated in conjunction with any other antenna or transmitter.
This receiver must be positioned at least 20 cm away from any persons
when in use.
Note: This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or
more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numerique de la classe B est conforme a la norme
NMB-003 du Canada.
CAUTION! Electrical shock can result from removal of the
receiver cover. Refer servicing to qualied service personnel. No
userserviceable parts inside. Do not expose to rain or moisture. The
circuits inside the receiver and transmitter have been precisely adjusted
for optimum performance and compliance with federal regulations. Do
not attempt to open the receiver or transmitter. To do so will void the
warranty, and may cause improper operation.

System 10 Installation and Operation
3
Because System 10 packaging is designed to hold all versions
of the system, some compartments in the carton may be intentionally
left empty.
The ATW-R1100 receiver includes a switching power supply that
automatically adapts to changes in mains voltage.
The versatile ATW-T1001 UniPak body-pack transmitter has both
a high-impedance input for instruments, and a low-impedance input
with bias connection for use with dynamic and electret condenser
microphones. The ATW-T1002 handheld transmitter features a
unidirectional dynamic microphone element.
Both the body-pack and handheld transmitters use internal AA batteries
and have Power/Mute switches and input Trim (level) adjustments.
Receiver Installation
Location
For best operation the receiver should be at least 3' (1 m) above the
ground and at least 3' (1 m) away from a wall or metal surface to
minimize reections. Keep the receiver antennas away from noise
sources such as other digital equipment, microwave ovens, as well as
away from large metal objects. Keep System 10 receiver 30' (9 m)
away from wireless access points. In multi-channel systems, position
receivers at least 3' (1 m) apart and keep operating transmitters at least
6' (2 m) from the receivers to help assure maximum RF performance.
VOLUME UNBALANCED
BAL ANCED
DC 12V IN
500mA
MIN. MAX.
1 1
2
4 6
3 5
1 2 3 4 5
Output Connection
There are two audio outputs on the back panel: balanced XLR-type
output and unbalanced ¼" TRS phone jack. Use shielded audio cable for
the connection between the receiver and the mixer. If the input of the
mixer is a ¼" jack, connect a cable from the ¼" unbalanced audio output
on the back of the receiver housing to the mixer. If the input of the
mixer is an XLR-type input, connect a cable from the balanced XLR-type
audio output on the back panel to the mixer.
Power Connection
Connect the DC plug on the included AC power adapter to the DC
power input on the back of the receiver. Secure the cord over the cord
hook on the back of the receiver, to keep the plug from being detached
by an accidental tug on the cord. Then plug the adapter into a standard
120 Volt 60 Hz AC power outlet.
(Note that the receiver has no power Off/On switch. The receiver will be
energized whenever the power adapter is connected and plugged into
the AC outlet. Unplug the power supply from the AC outlet when the
system is not in use — both for safety, and to conserve energy.)
Antennas
Rotate the permanently attached antennas in the shape of a “V” (both
45° from vertical) for best reception.
ATW-R1100 Receiver Controls and Functions
Figure A — Front Panel Controls and Functions
1. Antennas: Position the antennas as shown.
2. System ID Select Switch: Press to cycle through System ID
numbers. (System ID is an identical number assigned to a paired
receiver and transmitter for identication purposes.)
3. System ID Display: Shows System ID number.
4. Pairing Switch: Press to initiate pairing.
5. AF Peak Indicator: Only lights when audio distortion is present at
maximum modulaton. Not affected by position of Volume control.
6. Pair Indicator: Glows green to indicate presence of paired
transmitter. Also blinks green to indicate pairing mode activated.
Figure B — Rear Panel Controls and Functions
1. AF Level (Volume) Control: Adjusts audio output level of both AF
Output jacks; maximum output is fully clockwise.
2. Unbalanced Audio Output Jack: ¼" phone jack. Can be connected to
an unbalanced aux-level input of a mixer, guitar amp or tape recorder.
3. Balanced Audio Output Jack: XLRM-type connector. A standard
2-conductor shielded cable can be used to connect the receiver
output to a balanced microphone-level input on a mixer or
integrated amplier.
4. Power Input Jack: Connect the DC plug from the included in-line
AC adapter.
5. Cord Hook: Loop the cord around the cord hook to keep the DC
plug from pulling out accidentally.
Specyfikacje produktu
Marka: | Audio-Technica |
Kategoria: | mikrofon |
Model: | ATW-1101 |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Audio-Technica ATW-1101, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje mikrofon Audio-Technica

13 Stycznia 2025

6 Grudnia 2024

6 Grudnia 2024

6 Grudnia 2024

6 Grudnia 2024

6 Grudnia 2024

6 Grudnia 2024

6 Grudnia 2024

6 Grudnia 2024

6 Grudnia 2024
Instrukcje mikrofon
- mikrofon Sony
- mikrofon Yamaha
- mikrofon Sven
- mikrofon Logitech
- mikrofon Joy-It
- mikrofon President
- mikrofon Philips
- mikrofon Livoo
- mikrofon Plantronics
- mikrofon JBL
- mikrofon Roland
- mikrofon HyperX
- mikrofon Bose
- mikrofon Panasonic
- mikrofon Canon
- mikrofon Crestron
- mikrofon Behringer
- mikrofon Nedis
- mikrofon IK Multimedia
- mikrofon American DJ
- mikrofon Boss
- mikrofon Lenco
- mikrofon Majestic
- mikrofon Niceboy
- mikrofon Yealink
- mikrofon Blaupunkt
- mikrofon Teac
- mikrofon Speed-Link
- mikrofon Genesis
- mikrofon Line 6
- mikrofon DAP-Audio
- mikrofon Creative
- mikrofon Manhattan
- mikrofon Shure
- mikrofon Primus
- mikrofon Audac
- mikrofon DJI
- mikrofon Gembird
- mikrofon Godox
- mikrofon Røde
- mikrofon Konig & Meyer
- mikrofon Trust
- mikrofon Steelseries
- mikrofon Auna
- mikrofon Vimar
- mikrofon LD Systems
- mikrofon Mad Dog
- mikrofon NZXT
- mikrofon OneConcept
- mikrofon AVMATRIX
- mikrofon Renkforce
- mikrofon Rollei
- mikrofon Thomson
- mikrofon BOYA
- mikrofon Neumann
- mikrofon Wharfedale
- mikrofon Manta
- mikrofon Pyle
- mikrofon Zoom
- mikrofon NGS
- mikrofon Numark
- mikrofon Marantz
- mikrofon Sennheiser
- mikrofon Jabra
- mikrofon Chord
- mikrofon Vtech
- mikrofon Peerless-AV
- mikrofon Speco Technologies
- mikrofon Samson
- mikrofon PreSonus
- mikrofon NACON
- mikrofon Olympus
- mikrofon Vonyx
- mikrofon Bogen
- mikrofon Alto
- mikrofon Fluid
- mikrofon Razer
- mikrofon Peavey
- mikrofon ART
- mikrofon RCF
- mikrofon Rolls
- mikrofon Blue Microphones
- mikrofon Prodipe
- mikrofon TC Helicon
- mikrofon JLab
- mikrofon Axis
- mikrofon Deity
- mikrofon Majority
- mikrofon Kurzweil
- mikrofon Klark Teknik
- mikrofon Telefunken
- mikrofon Proel
- mikrofon Audix
- mikrofon Aluratek
- mikrofon Omnitronic
- mikrofon Hama
- mikrofon Mackie
- mikrofon Palmer
- mikrofon SE Electronics
- mikrofon MXL
- mikrofon GoPro
- mikrofon Sharkoon
- mikrofon Saramonic
- mikrofon Gravity
- mikrofon Insignia
- mikrofon GVM
- mikrofon Harley Benton
- mikrofon Marshall Electronics
- mikrofon Kali Audio
- mikrofon Tracer
- mikrofon Joby
- mikrofon AKG
- mikrofon Azden
- mikrofon AVerMedia
- mikrofon Atlas Sound
- mikrofon Gemini
- mikrofon Trevi
- mikrofon Technaxx
- mikrofon Fishman
- mikrofon Radial Engineering
- mikrofon Lectrosonics
- mikrofon Polsen
- mikrofon Power Dynamics
- mikrofon AEA
- mikrofon Senal
- mikrofon TOA
- mikrofon Monacor
- mikrofon HQ Power
- mikrofon Electro-Voice
- mikrofon Dörr
- mikrofon Tascam
- mikrofon Vicoustic
- mikrofon Karma
- mikrofon Elgato
- mikrofon Vocopro
- mikrofon SPL
- mikrofon Xvive
- mikrofon Alfatron
- mikrofon Sound Devices
- mikrofon Easyrig
- mikrofon Relacart
- mikrofon DPA
- mikrofon Reloop
- mikrofon Fenton
- mikrofon Artsound
- mikrofon Chandler
- mikrofon Sescom
- mikrofon Sonic Presence
- mikrofon Lewitt
- mikrofon Kopul
- mikrofon Movo
- mikrofon SmallRig
- mikrofon Earthworks
- mikrofon Sontronics
- mikrofon Anywhere Cart
- mikrofon Midas
- mikrofon Atlas
- mikrofon American Audio
- mikrofon Hähnel
- mikrofon Easypix
- mikrofon Brigmton
- mikrofon Techly
- mikrofon Connect IT
- mikrofon Steren
- mikrofon Sandberg
- mikrofon Galaxy Audio
- mikrofon Pyle Pro
- mikrofon Valcom
- mikrofon Bigben
- mikrofon IDance
- mikrofon Simplecom
- mikrofon QTX
- mikrofon Konig
- mikrofon Austrian Audio
- mikrofon Pure Acoustics
- mikrofon T'nB
- mikrofon Phonak
- mikrofon Countryman
- mikrofon ESI
- mikrofon Beyerdynamic
- mikrofon Vaddio
- mikrofon Golden Age Project
- mikrofon Blue
- mikrofon Apart
- mikrofon Turtle Beach
- mikrofon Day
- mikrofon Max
- mikrofon IC Intracom
- mikrofon Celly
- mikrofon Comica
- mikrofon Clockaudio
- mikrofon Audient
- mikrofon Xtreme
- mikrofon Skytec
- mikrofon M-Audio
- mikrofon Krom
- mikrofon Monoprice
- mikrofon Neewer
- mikrofon ENDORFY
- mikrofon Aston
- mikrofon Ambient Recording
- mikrofon Solid State Logic
- mikrofon Adastra
- mikrofon TeachLogic
- mikrofon Citronic
- mikrofon Universal Audio
- mikrofon Warm Audio
- mikrofon Ultimate Support
- mikrofon NOX
- mikrofon PSSO
- mikrofon United
- mikrofon Manley
- mikrofon Tonsil
- mikrofon Royer Labs
- mikrofon Neat
- mikrofon Hohner
- mikrofon Thronmax
- mikrofon ClearOne
- mikrofon Mojave
- mikrofon Singing Machine
- mikrofon Auray
- mikrofon Bontempi
- mikrofon Triton
- mikrofon ITek
- mikrofon Schertler
- mikrofon Pixel
- mikrofon Antelope Audio
- mikrofon ONYX
- mikrofon MOZA
- mikrofon DB Technologies
- mikrofon Hollyland
- mikrofon Epcom
- mikrofon Point Source Audio
- mikrofon Synco
- mikrofon Fun Generation
- mikrofon Nady
- mikrofon Oktava
- mikrofon Aston Microphones
- mikrofon ANT
- mikrofon IMG Stage Line
- mikrofon Eikon
- mikrofon JZ Microphones
- mikrofon Perfect Choice
- mikrofon Owl Labs
- mikrofon Catchbox
- mikrofon White Shark
- mikrofon ViolaWave
- mikrofon Shadow
- mikrofon Klover
- mikrofon Soundsation
- mikrofon Nuance
- mikrofon TIE Audio
- mikrofon CAD Audio
- mikrofon Phonic
- mikrofon JTS
- mikrofon Intricon
- mikrofon The T.bone
- mikrofon Miktek
- mikrofon Stageclix
- mikrofon Townsend Labs
- mikrofon Sabian
- mikrofon Tula
- mikrofon DAP
- mikrofon Schoeps
- mikrofon Sonuus
- mikrofon Mars Gaming
- mikrofon AMT
- mikrofon AmpliVox
- mikrofon Eurosound
- mikrofon Williams Sound
- mikrofon Lorgar
- mikrofon KeepOut
- mikrofon Audibax
- mikrofon IMG Stageline
- mikrofon Scope Labs
- mikrofon Lauten Audio
- mikrofon Mirfak Audio
- mikrofon CKMOVA
- mikrofon DOCKIN
- mikrofon Nowsonic
- mikrofon Tonor
- mikrofon Antelope
- mikrofon MILAB
- mikrofon Sanken
- mikrofon Switchcraft
- mikrofon PureLink
- mikrofon Isovox
- mikrofon Glemm
- mikrofon Voice Technologies
- mikrofon PSC
- mikrofon Microtech Gefell
Najnowsze instrukcje dla mikrofon

15 Stycznia 2025

15 Stycznia 2025

15 Stycznia 2025

15 Stycznia 2025

14 Stycznia 2025

13 Stycznia 2025

12 Stycznia 2025

11 Stycznia 2025

10 Stycznia 2025

10 Stycznia 2025