Instrukcja obsługi Arlec DC681

Arlec Niesklasyfikowane DC681

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Arlec DC681 (2 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 5 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/2

5 6

Introduction

The Wireless Door Chime (DC681) consists

of t wo separate units:-

1. Push Button Unit

(Transmitter)

2. Chime Unit

(Receiver)

These units are completely self-contained

and no wiring bet ween them is necessary.

Range

Up to 50 metres.

NOTE: Range depends on location,

temperature, and battery condition.

Important Notes

1. The operation and range of your Wireless Door Chime depends on location,

temperature and bat tery condition.

2. Try different locations in your home, ideally more than 1 metre from the ﬂoor.

Move Chime unit closer to Push But ton unit to improve operation.

3. Do not expose either unit to rain or immerse in water.

4. Avoid locations where the Push But ton unit is exposed to direct summer sunlight.

5. Do not leave exhausted batteries in Push But ton unit.

6. Clean only with a damp cloth and mild detergent. Do not use solvents.

7. In an event of power outage, surge or unstable main power supply, your door chime

will default to factory setting. Please reset the unit according to ‘Resetting the Unit’.

Security

When you are away from home for long periods you may wish to leave your Chime Unit

with one of your neighbours so that they can monitor callers to your house during

your absence.

Trouble Sooting & User Hints

Problem Possible Cause Suggested Remedy

Chime

does not

sound.

1. Units are out of range (max.

range 50m) .

Operate the Chime unit within the

operation range (50m).

2. Push Button and Chime units

are not on same frequency

coding.

Re-set the frequency coding (see Code

Selection) or select a dif ferent tone (see

Tone Selection).

3. Flat Push Button bat tery. Change the batt ery.

4. Wrong polarity of bat tery in

Push Button.

Re-insert bat tery with polarity to match

markings.

5. Power outage, surge or

unstable main power supply. Re-set unit according to

‘Resetting the Unit’.

Chime

sounds

without

Push

Button

being

pressed

1. A power interruption to the

Door Chime unit plus a similar

door chime product operating

nearby has caused the chime

unit to reset to the incorrect

House Code

A. Switch off the Chime Unit for at least

1 minute. Switch on again. It should

beep twice. Press the Push Button to

operate the chime. This re-sets the

House Code in the Chime Unit or;

B. Re-set the frequency coding (see Code

Selection

2. A similar Wireless Door Chime

product is operating nearby on

the same House Code.

Re-set the House Code

(see Code Selection).

3. Interference from CBs, Taxis or

remote control toys operating

on the same frequency.

Re-set the House Code

(see Code Selection).

CPIN002793

Plug-In Wireless Door Chime

with Gloss White Finish

DC681

Installation & Operating

Instructions

CPIN002793

Warranty

Arlec guarantees this product in accordance with the Australian Consumer Law.

Arlec also warrants to the original ﬁrst purchaser of this product (“you”) from a retailer that

this product will be free of defects in materials and workmanship for a period of 12 months

from the date of purchase; provided the product is not used other than for the purpose, or in

a manner not within the scope of the recommendations and limitations, speciﬁed by Arlec,

is new and not damaged at the time of purchase, has not been subjected to abuse, misuse,

neglect or damage, has not been modiﬁed or repaired without the approval of Arlec and has

not been used for commercial purposes (“Warranty”).

If you wish to claim on the Warranty, you must, at your own expense, return the product, and

provide proof of original purchase and your name, address and telephone number, to Arlec at

the address below or the retailer from whom you originally purchased the product within 12

months from the date of purchase.

Arlec will (or authorise the retailer to) assess any claim you may make on the Warranty in the

above manner and if, in Arlec’s reasonable opinion, the Warranty applies, Arlec will at its own

option and expense (or authorise the retailer to) replace the product with the same or similar

product or repair the product and return it to you or refund the price you paid for the product.

Arlec will bear its own expenses of doing those things, and you must bear any other expenses

of claiming on the Warranty.

The Warranty is in addition to other rights and remedies you may have under a law in relation

to the product to which the Warranty relates.

Our goods come with guarantees that cannot be excluded under the Australian Consumer

Law. You are entitled to a replacement or refund for a major failure and for compensation for

any other reasonably foreseeable loss or damage. You are also entitled to have the goods

repaired or replaced if the goods fail to be of acceptable quality and the failure does not

amount to a major failure.

Arlec Australia Pty. Ltd. ACN 009 322 105 (“Arlec”) gives the Warranty.

Arlec’s telephone number, address and email address are:

Customer Service: (03) 9982 5111

New Zealand Toll Free: 0800 003 329

Building 3, 31 – 41 Joseph Street, Blackburn North, Victoria, 3130

Blackburn North LPO, P.O. Box 1065, Blackburn North, 3130

Email: custservice@arlec.com.au

Code Selection

The push button unit generates random code sequences to which the chime unit is

able to learn. Should your door chime unit activate intermittently for no apparent

reason, the uncontrolled activation may be caused by another unit nearby or from a

device operating on the same frequency.

Code/Push Button Limiting Switch

Your door chime unit is capable of working with a

maximum of 4 Bell Push But ton units at 4 different

frequency channels. If your door chime unit activate

intermit tently for no apparent reason, it might caused by

a nearby device working on a similar frequency channel.

To eliminate frequency channel interruption, Code/Bell

Push Button Limiting Switch is to limit the Bell Push

But ton unit and /or frequency channel that your door

chime unit can be activated by.

1. Connect the Door Chime to the mains power and press

the Bell Push Button once, the door chime will sound

to indicate that 1st operating code is registered and

memorized. This is the factory setting and intended

to limit the activate frequency channel and Bell Push

But ton unit to 1.

2. To register 2nd Bell Push Button operating code

and/or frequency channel, Press and hold the code setting switch on the door

chime unit for 1 second, it will give a “Beep” sound to indicate that door chime

is ready to learn the 2nd operating code, press the 2nd Bell Push Button once,

the door chime will sound to indicate that 2nd operating code is registered and

memorized. This will allow 2 dif ferent Bell Push Button units and /or frequency

channels working with the door chime at the same time.

3. Repeat the same procedure for the 3rd and 4th Bell Push But tons. The maximum

amount of Bell Push But ton units and frequency channels that the door chime

unit can be work at the same time are 4.

4. To reset Code/Bell Push But ton limiting function, disconnect the door chime unit

from mains power for at least 1mins, and reconnect, this will reset the door chime

unit to learn 1 Bell Push Button and/or frequency channel only.

Note: Power outage, surge or unstable main power supply will erase or rest the Code/

Bell Push Button limiting function, and low battery in push button unit will also erase

or rest the registered frequency channel between the door chime and push button

unit, if the door chime unit does not sound when push button unit depressed, please

unplug the door chime unit from power point, replace batteries on push button unit,

then re-plug the door chime unit into power point and set up both units again.

Resetting the Unit

To avoid uncontrolled activation:

1. Switch off the Chime Unit for at least 1 minute.

2. Switch back on. A double beep should be heard indicating that the unit is in

learning mode.

3. Press the Push But ton. The chime should sound to indicate code selection.

432

WARNING

This product contains a Lithium Coin type battery.

WARNING! Please ensure the coin battery is kept OUT OF REACH OF CHILDREN.

The battery presents a signiﬁcant choking and burn hazard to young children

should they swallow a battery. Under 4 year-olds are especially prone to

accidental swallowing of objects such as these.

If a lithium coin battery is swallowed, SEEK IMMEDIATE MEDICAL ATTENTION.

Do not let the child eat or drink; Do not induce vomiting.

To keep your children safe:

• Keepdevicesthatusecoinbatteriesoutofreachofsmallchildren

• Keepnewbatteriesintheirpackaginguntilreadytouseandstore

in places out of reach of children

• Safelydisposeofspentbatteriesimmediately

• Sharethisinformationwithyourfamily,friends,caregiversandbabysitters.

We have designed the coin battery holder to require dexterit y normally beyond that

of a small child to access, but nevertheless you should always follow the advice

given above.

Push Button

1. Push Button unit is operated by 1 x 3 volt Lithium battery (CR2032 - included).

2. Remove the back of case by pushing in the tab on the bot tom with a small, ﬂat

screwdriver.

3. The 3 volt Lithium bat tery (CR2032) is already installed.

Simply pull off the isolation strip which will allow the battery to make electrical contact.

NOTE: When the push button unit is depressed, an orange LED light will lit on, but this

is not an indicator of the push button unit battery level. It is recommended to replace

batteries once a year to ensure range and transmission reliability.

To Replace the Battery

Remove the locking screw from the bat tery holder clip and remove old

batter y. Insert 1 x 3 volt Lithium bat tery (t ype CR20 32) in the battery

compartment, ensuring the battery polarity is correct as in Figure 1.

Replace clip and tighten locking screw to hold bat tery ﬁrmly in place.

Chime Unit

The Chime Unit is powered by 24 0 volt and should be plugged into any

convenient household power point.

INSTALLATION

Chime Unit

Plug the Chime Unit into any household power point and switch power on. The

Chime Unit indicator lamp will glow and it will beep twice to indicate it is ready.

Press the push but ton unit to test the chime.

NOTE: Do not mount the chime and push button unit near metal objects, UPVC frame,

heat/radio source, security door or in close proximity to any radio emitting equipment.

The range of the unit may be substantially reduced.

Push Button Unit

The Push Button unit has t wo mounting holes on rear plate of unit that must be

pushed through before unit can be mounted.

1. Remove rear plate of unit (see bat tery installation).

2. Push through tabs in mounting holes.

3. Using the back plate of the Push Button unit as a guide, mark the position

of holes onto mounting surface.

4. Drill appropriately sized holes and insert wall plugs if required.

5. Secure the back plate of Push Button unit to mounting unit.

6. Clip Push But ton unit to back plate.

Alternatively the Push But ton unit can be at tached to smooth mounting surfaces such

as painted wood, glass and plastic using Self-Adhesive Pad (supplied).

Do not mount the push button unit on metal or near metal door frame, securit y door,

metal furniture or in close proximit y to any radio emit ting equipment.

The range of the unit may be substantially reduced.

Door Chime Operation

Once the Push Button and Chime units have been installed in their desired locations,

the system is ready for use.

Depress but ton on Push But ton unit momentarily, and chime should sound. Press button

again to repeat. Continual pressing of the button will not repeat the chime. If chime

fails to sound, check bat teries in push button and check power is on to Chime Unit.

Tone Selection

The Wireless Door Chime is supplied with 8 built-in chimes.

Westminster Chime Twinkle Twinkle

Double Ding-Dong It’s a Small World

Circus Theme Dog Barking

Banjo on My Knee Telephone Ring

To change the chime tune, remove the Push Button Unit ’s rear cover.

Inside the Push But ton Unit locate the small Tune Selector push button marked ‘S’

(Ref. Figure 1). Each time that this Tune Selector push button is pressed, the next of

the 8 melodies will be played. You can step through and listen to each in turn. When

you hear the melody you wish to choose, do not press the tune selector again. The

chime will play the selected melody each time the bell press is pushed. At any time

you can select another melody by repeating the tune selector but ton process.

Reﬁt the Push But ton Unit rear cover.

Whenever the Push Button Unit bat tery is ﬁtted or replaced, the chime tune may

default to the Westminster Chime.

Fig 1.

CPIN002793

Code/Bell Push Button

Limiting Switch

Specyfikacje produktu

Marka:	Arlec
Kategoria:	Niesklasyfikowane
Model:	DC681

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Arlec DC681, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje Niesklasyfikowane Arlec

Arlec DC681 Instrukcja

25 Września 2024

Arlec RT500 Instrukcja

25 Września 2024

Instrukcje Niesklasyfikowane

Najnowsze instrukcje dla Niesklasyfikowane

Black Diamond BD1121530000ALL1 Instrukcja

15 Października 2024

Husqvarna K 970 SmartGuard Instrukcja

15 Października 2024

Stihl HT 70 Instrukcja

15 Października 2024

Ernesto H14270 Instrukcja

15 Października 2024

Uniden BT MIC KIT Instrukcja

15 Października 2024

Vaude Omnis Bike 26 Instrukcja

15 Października 2024

ART ProChannel II Instrukcja

15 Października 2024

Aukey DR02J Instrukcja

15 Października 2024

Master Lock 653EURD Instrukcja

15 Października 2024

Roland FR-18 Diatonic Instrukcja

15 Października 2024