Instrukcja obsługi Apricorn Velocity Duo X2

Apricorn Kontroler Velocity Duo X2

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Apricorn Velocity Duo X2 (2 stron) w kategorii Kontroler. Ta instrukcja była pomocna dla 11 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/2
Power-down the system and physically remove the power
cord(s) from the system.
Remove the cover from the system’s chassis, following
instructions provided by the manufacturer.
Select an available PCIe Gen 1 / Gen 2 (x2, x4, p1-x8 or x16)
slot and insert the Velocity Duo card into the slot, as shown
in Figure 1. ( p1-x2 slots are very rare in desktop NOTE:
systems, typical installation will use a p1-x4 slot).
Hold the Velocity Duo card at the edges and press down
gently into place.
Secure the Velocity Duo metal bracket to the system
chassis by tightening the slot screw.
After the Velocity Duo is installed, replace the chassis
cover, reconnect the power cord(s) and boot the computer.
Follow the directions below to complete your upgrade.
1.
2.
3.
4.
5.
6.
7.
Installing the Velocity Duo
in your desktop computer
Velocity Duo Quick Start Guide
To prevent ESD
(Electrostatic Discharge) damage
Use an ESD wrist strap or discharge static electricity by
touching a grounded bare metal surface before handling,
installing, and removing the Velocity Duo. Observe proper
ESD grounding techniques. Store your HDD or SSD in an
anti-static bag until you are ready to install it in the system.
When installing and removing the Velocity Duo Card hold by
the edge of the printed circuit board (PCB), and avoid
touching components including connectors.
IMPORTANT HANDLING INFORMATION
Connecting your SSD to the Velocity DUO Card
Slide both of your
SSDs onto the SATA
connectors on the
Velocity Duo Card. Use
4 mounting screws in
each drive to secure
them to the Duo Card.
SATA connector
SATA connector
Figure 1. Installing the Velocity Duo on
PCIe Gen 1 / Gen 2 slot
NOTE: Windows XP users and those using the Velocity
Duo with a boot disk (i.e. with OS already installed)
Before connecting your SSD to the Velocity Duo, please refer
to the directions below for installation of Windows drivers.
PCIe Gen 1/Gen 2 ( x2 slot or larger)
To ensure optimal RAID  functionality, both of the SSDs on the Velocity Duo must be identical (same brand, same
firmware revision and capacity) Additionally, prior to data cloning, each drive must be eroed out using a disk utility such
as Gparted, Parted agic, or a utility native to your OS. Since RAID  is strictly a performance-enhancing array with data
being striped across 2 drives, if one of those drives should fail, all data on both will be lost. When using Velocity Duo with
RAID  configuration, regular backup is recommended to minimie data loss.
Apricorn’s Technical Support Specialists are available
8.00am to 5.00pm, PST Monday through Friday
Email our Technical Support Department at
support@apricorn.com or call 800-458-5448 option 3
Free Tech Support
Need help? Download product manuals,
checkout FAQs and set up questions at
www.apricorn.com
Changing the boot drive on your PC
Once you have cloned your system to your Velocity Duo drive, you have two options.
Remove your original drive, thereby forcing your system to boot from the Velocity Duo drive.
Go into your system’s BIOS and change your boot order to the Velocity Duo drive, keeping your original drive for storage.
Entering your computer’s BIOS to change the boot order is dependent on your particular system. For directions that apply to your particular
system, please refer to your computer’s product manual.
1.
2.
Note: Do not turn your computer off or allow your computer to sleep during the cloning process. Let the process continue until you
see the congratulations screen. When the congratulations screen appears, select “Quit EZ Gig” and then turn off your computer.
Apricorn’s innovative EZ Gig allows you to clone your entire hard drive or deselect data files from the cloning process to save space, giving
you the option to run your OS and applications from a fast, smaller SSD boot drive, while keeping your documents and media files on your
original hard drive. As EZ Gig is able to run from inside the Windows operating system, simply download EZ Gig from Apricorn’s website
(apricorn.com/products/software/ezgig.html) and run the program. The EZ Gig wizard will guide you through the cloning process in a few
simple steps.
Cloning your hard drive using
Apricorn’s EZ Gig for Windows
For complete instructions go to Apricorn’s
website to download the Velocity Duo manual.
After downloading EZ Gig from Apricorn’s site, open the
EZ Gig program or double click on the EZ Gig icon to get
started. Click “Run EZ Gig” from the EZ Gig Start-up
Options window.
Select “Let’s Get Started” from the EZ Gig main screen.
EZ Gig will then scan for connected drives.
Note: The Velocity Duo card must be installed for EZ Gig to
run. EZ Gig will only run with Apricorn Upgrade devices.
1.
2.
The EZ Gig Wizard will then ask you to choose your Source
drive and your Destination drive. Choose your internal drive
as the Source and the Velocity Duo drive as your
Destination drive.
Once the Source and Destination drives are selected,
EZ Gig will give you the option of cloning your entire system
or deselecting data files from the cloning process to save
space. Make your selection then click “Start Clone.”
Once the clone is complete, you can boot your computer
from the new drive. Please refer to the directions below.
3.
4.
5.
Cloning your hard drive using Apple’s Built-in Disk Utility
Starting in Mac OSX 10.4 it is possible to use the Disk Utility application to perform a Restore operation of the Boot disk to another disk.
Starting in OSX 10.7 this operation needs to be performed while booted in Recovery mode, but the process is still the same. Open Disk Utility
from Applications / Utilities / Disk Utility. Select the Restore tab located at the top of the application window. Carefully drag your original boot
volume to the Source field, and then drag the new SSD mounted to the Velocity Duo to the Destination field. Click the Restore button and the
process will begin. Once the process has finished you will quit the Disk Utility application, and open the System Preferences. Use the Startup
Disk preference pane to choose your new Velocity Duo as the startup disk. Reboot the Mac and the OS will start from the new disk.
Installation of drivers and initial setup of the Velocity Duo
If the Velocity Duo drive is not detected, check the drive connections and ensure that the Velocity Duo is installed correctly in the PCIe slot.
Windows - Before booting any version of Windows from the Velocity Duo, Windows must detect and install drivers for the new
storage controller. If you installed new blank SSDs on the Velocity Duo (directions above) AND are running Windows 7 or Vista,
drivers will be automatically installed. If you are installing a boot drive (i.e. with OS already installed) to the Velocity Duo or are
running Windows XP, please ensure that Windows is booted one time with the Velocity Duo card installed in the computer but
without the SSDs connected. After the drivers are installed, the SSDs may be attached to the Velocity Duo.
Windows XP owners need to download drivers from www.apricorn.com/downloads/VelDuo_drivers.zip
Windows Vista and 7 will automatically detect and install the drivers from Windows Update.
Mac - Hardware support for the Velocity Duo product family is built into the Mac OSX, so no driver install is necessary.
Mac OSX can be booted from any drive attached to the Velocity Duo.
PC CLONING SOFTWARE DOWNLOAD
Apricorn EZ Gig Software for the Velocity Duo
www.apricorn.com/products/software/ezgig.html

Specyfikacje produktu

Marka: Apricorn
Kategoria: Kontroler
Model: Velocity Duo X2

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Apricorn Velocity Duo X2, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Kontroler Apricorn

Apricorn

Apricorn Velocity Duo X2 Instrukcja

14 Września 2024

Instrukcje Kontroler

Najnowsze instrukcje dla Kontroler

DJI

DJI Motion Controller Instrukcja

14 Stycznia 2025
8BitDo

8BitDo Ultimate C Wired Controller Xbox Instrukcja

11 Stycznia 2025
Balam Rush

Balam Rush Kontrol React G575 Instrukcja

11 Stycznia 2025
PCE Instruments

PCE Instruments PCE-RE100P Instrukcja

10 Stycznia 2025
PCE Instruments

PCE Instruments PCE-RE21R Instrukcja

10 Stycznia 2025
Sonance

Sonance VC30R Instrukcja

8 Stycznia 2025
BeamZ

BeamZ WTR10-5 Instrukcja

5 Stycznia 2025
Audibax

Audibax MC1000 Instrukcja

5 Stycznia 2025
Somfy

Somfy Keypad 2 RTS Instrukcja

1 Stycznia 2025
Somfy

Somfy Keypop RTS Instrukcja

1 Stycznia 2025