Instrukcja obsługi Apart PM7400MKII

Apart odbiornik PM7400MKII

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Apart PM7400MKII (4 stron) w kategorii odbiornik. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/4
12
3
4
5
6
7
8
9
10 12 14 15 16
11 13
1. Microphone 1 TRS input jack. this jack has a XLR mirror connector at the back. You can use the XLR or the front
jack, but not both simultaneously. You can apply phantom power by closing jumper JP1 inside the device, contact a
qualied technician to do this.
2. Vox/Ext.mute switch. when this switch is pressed, you activate the vox or ‘voice-over’ mute function on mic 1,
the vox level can be set at the rear. When the switch is out, i.e. not pressed, you can activate mute with an external
switch, the ext. mute connector is also at the back.
3. Mic 1 level controller.
4. Mic 2 level controller.
5. Microphone 2 TRS input jack. this jack has a XLR mirror connector at the back,. You can use the XLR or the front
jack, but not both simultaneously. You can apply phantom power by closing jumper JP2 inside the device, contact a
qualied technician to do this.
6. Mic 1 and 2 bass tone control. for better speech intelligibility, gently cut low frequencies. A low cut lter to avoid
popping noises is already built-in and can not be deactivated.
7. Mic 1 and 2 mid tone control..
8. Mic 1 and 2 treble tone control.
9. Mains power switch and power led. when you switch the device on, the blue led will indicate that the power is on.
10. Music or line input bass tone control.
11. Music or line input mid tone control.
12. Music or line input treble tone control.
13. Music or line source volume control. Normally this level controller is turned fully clockwise, however, in some
cases it can be usefull to obtain a good loudness balance between music or line inputs and mic inputs.
14. Music or line level input selector. with this rotary switch you can select between line 1-6 stereo line level inputs.
15. Zone 1 volume control with L/R signal indicator leds. use this level controller as the main zone 1 volume control-
ler. The leds will light up when a strong signal is present at the zone 1 output.
16. Zone 2 volume control with L/R signal indicator leds. use this level controller as the main zone 2 volume control-
ler. The leds will light up when a strong signal is present at the zone 2 output.
18 19 20
17 21
22
23
24
25
26
27
28 29 30 31 32 33
17. Ground connector. Connect your system’s ground or safety ground on this connector if this is not already done
by mounting the unit in a properly grounded rack.
18. Line 1 right input on balanced XLR connector.
19. Line 1 left input on balanced XLR connector.
20. Line 2 L/R cinch or RCA connector.
21. Line 3 L/R cinch or RCA connector.
22. Line 4 L/R cinch or RCA connector.
23. Line 5 L/R cinch or RCA connector.
24. Line 6 L/R cinch or RCA connector.
25. Line 6 L/R cinch or RCA connector.
26. Mono/stereo switch. Pressing this switch, the stereo line inputs 1 to 6 are mixed to mono.
27. Ext. mute switch connector. Connect your external mute switch on this connector, do not apply any voltages on
this connector !!!
28. Vox mute level. Use this controller to set the level where the ‘vox’ mute circuitry of mic 1 will be active.
29. Zone 2 right output on balanced XLR connector.
30. Zone 2 left output on balanced XLR connector.
31. Mic 2 XLR/ TRS jack combo input. This is a copy of the front MIC 2 TRS input jack. You can use the front or
rear input, but not simultaneously. You can apply phantom power to the mic by closing jumper JP1 inside the
PM7400 MKII. Only a qualied technician can do this !
32. Mic 1 XLR/ TRS jack combo input. This is a copy of the front MIC 1 TRS input jack. You can use the front or
rear input, but not simultaneously. You can apply phantom power to the mic by closing jumper JP2 inside the
PM7400 MKII. Only a qualied technician can do this !
33. Mains inlet/mains fuse connector. Connect the supplied mains cable here. There is also a 315 mAT mains fuse
inside this connector. In case the fuse blows, replace it only with a fuse of the same rating.

Specyfikacje produktu

Marka: Apart
Kategoria: odbiornik
Model: PM7400MKII

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Apart PM7400MKII, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje odbiornik Apart

Apart

Apart SBR160 Instrukcja

14 Października 2024
Apart

Apart REVAMP2060T Instrukcja

9 Września 2024
Apart

Apart CHAMP-3D Instrukcja

5 Września 2024
Apart

Apart MA125 Instrukcja

5 Września 2024
Apart

Apart CHAMP-ONE-SLV Instrukcja

4 Września 2024
Apart

Apart PA8250 Instrukcja

3 Września 2024
Apart

Apart CONCEPT1T Instrukcja

2 Września 2024
Apart

Apart MA200 Instrukcja

2 Września 2024
Apart

Apart REVAMP1680 Instrukcja

1 Września 2024
Apart

Apart MA240 Instrukcja

31 Sierpnia 2024

Instrukcje odbiornik

Najnowsze instrukcje dla odbiornik

Marantz

Marantz SR-8000 Instrukcja

15 Stycznia 2025
AKAI

AKAI AM-32 Instrukcja

15 Stycznia 2025
Peavey

Peavey CKd 608 Instrukcja

15 Stycznia 2025
OSD Audio

OSD Audio Nero HTX4150 Instrukcja

14 Stycznia 2025
S.M.S.L

S.M.S.L PA200 Instrukcja

14 Stycznia 2025
Pyle

Pyle PFMRA340BB.5 Instrukcja

13 Stycznia 2025
Wavtech

Wavtech link700.4plus Instrukcja

13 Stycznia 2025
Behringer

Behringer NU6000DSP Instrukcja

12 Stycznia 2025
Denon

Denon DRA-935R Instrukcja

12 Stycznia 2025
Kenwood

Kenwood KMM-BT508DAB Instrukcja

12 Stycznia 2025